WEISER GED240 Elements Satin Nickel Keyless Entry Door Lock Deadbolt Lock Installation Guide

June 14, 2024
Weiser

WEISER GED240 Elements Satin Nickel Keyless Entry Door Lock Deadbolt Lock

Required tools

Parts in the box

Prepare the door and check the dimensions

If drilling a new door, use the supplied template and the complete door drilling instructions

  • Measure to confirm that the hole in the door is either 54 mm (2-1/8 in) or
  • Meerse to commit the backset is Measured to confirm that the hole in the door edge is 25 mm (1 in).
  • Measure to confirm that the door is between 35 mm and 44 mm

Note: Additional door preparation may be required for doors with 38 mm (1-1/2 in) holes.
Note: Please contact customer service if the door thickness exceeds 44mm (1-3/4 in) for a thick door kit.

Install the latch and strike

  • Hold the latch in front of the door hole, with the latch
  • face flush against the door edge
  • Is the door edge chiseled?
  • Install strike on the door frame.

Is the rectangular-shaped hole centered in the door hole?
IMPORTANT: Make sure the latch bolt is fully retracted (in the unlocked position).

Install the exterior keypad

  • What is the diameter of the hole in the door?
  • Locate screws for step 3C and keep them within reach
  • Install exterior keypad and mounting plate

Install the interior assembly

Remove interior cover from interior assembly

Secure the interior assembly onto the mounting plate

Install the batteries in the interior assembly

  • Install 4 AA batteries in interior assembly
  • Install interior cover for the interior assembly

Add user codes (12 max)

****During User Code programming, a time will occur if the keypad is not pressed for 5 seconds and you will need to restart the procedure. For security reasons, the first 4 digits of each User code must be unique. For
example, you are unable to program a user code 1-2-3-4-5 as well as a user code 1-2-3-4-6.

Note: After the first User Code is created, the latch bolt will automatically retract and extend to learn the locking and unlocking direction of the door. The lock button will indicate success or failure. GREEN: Success RED: Unsuccessful

Test the lock (review normal operation)

  • Before you can lock and unlock the door a User Code must be created. Refer to Step 6 for instructions on how to create a User Code.
  • Confirm that the code(s) added in the previous step can unlock the door.
  • To lock your door, press the lock button. The lock will beep twice and the lock button will flash amber as the deadbolt extends
  • To unlock your door, enter the user code. The lock will beep twice and the lock button will flash areen as the deadbolt retracts.

Adding a One-time User Code

  • Up to 2 One-time User Codes can be saved. One-time User Codes should be 4 to 8 digits in length.
  • The One-Time User Code will be deleted automatically after it is used. The same One-Time User
  • Code can be created again after it’s used.

**Delete a Single User Code

**

If unsuccessful
Make sure you enter the same user code in steps 4 and 6. Test code while the door is open. Test the User Code to make sure it no longer unlocks the door. If a button is not pressed within 5 seconds, the system will time out, and you will need to restart the procedure.

Delete ALL User Codes
Note: The Keypad locking function will be disabled when User Codes are deleted. The lock can only be operated manually by a key during this time

Enable/ Disable Audio
Note: The LED status indicator will still function once audio is disabled. Repeat the programming steps to enable the audio.

Enable/ Disable User Codes
Note: When all User Codes are disabled, all electronic functions will be disabled as well.
The door must be locked or unlocked manually with the key. Repeat the programming steps to enable the User Codes.

**Enable/ Disable Auto-Lock

**

Change Auto-Lock Time Delay

**Door Rehanding

**

The latch bolt will extend and retract to learn the orientation of the door.
Note: Perform this process for the lock to learn the locking and unlocking direction of the door. This feature is used for the lock to learn the orientation of your door (left- or right-handed). If a stuck/jammed bolt error continues to occur after performing this step, please make sure there is no obstruction from the strike or door jamb to prevent the bolt from extending.

Factory Reset

Note: The lock must be in an unlocked position to factory reset A factory reset will delete all User Codes and change all programming to factory settings. At this time, the lock can only be locked or unlocked manually with the key.

Add/ Change Programming Code

Enable/ Disable Programming Code
Optional: A Programming Code enables you to make programming changes without needing to access the Programming Button. This is ideal for landlords to program the lock without access to the interior programming button.
Note: Once Programming Code is enabled, the Programming Button is disabled and can only be used to factory reset the lock. One Programming Code between 4 to 8 digits can be saved and cannot be the same as any User Code and cannot be used as a User Code to unlock the lock.

To program the lock with Programming Code

Deadbolt at a Glance

System Alerts

Important Safeguards

  1. Read all instructions in their entirety.
  2. Familiarize yourself with all warning and caution statements.
  3. Remind all family members of safety precautions.
  4. Always have access to your lock’s standard key.
  5. If using the Auto-Lock features, make sure you have your standard key with you to prevent locking yourself out.
  6. Familiarize yourself with the system alerts.
  7. Replace low batteries immediately.
  8. Dispose of used batteries according to local laws and regulations.

CAUTION
This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. To enhance security and reduce risk, you should consult a qualified locksmith or other security professional. Prevent unauthorized entry. Since anyone with access to the back panel can change the User Codes, you must restrict access to the back panel and routinely check the User Codes to ensure they have not been altered without your knowledge. The use of a programming code can help protect your system’s settings.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals