inse S9 Cordless Vacuum Cleaner User Manual

inse S9 Cordless Vacuum Cleaner

IMPORTANT SAFETY INSTRUCTIONS

Do not place the vacuum cleaner close to heat sources, radiation, or burning cigarettes.

• Do not use the appliance to remove the following objects.
  1. All liquids such as water and solvents.
  2. Lime, cement, ash, and other Construction dust and garbage.
  3. Hot objects, such as cigarette butts.
  4. Sharp debris, such as glass shards, etc.
  5. No flammable and explosive articles, such as gasoline or alcohol products.
• Do not let children play with and operate the vacuum cleaner to prevent accidents.
• Your vacuum cleaner is an electric appliance: it must be used inappro priately.
• Do not leave the operating vacuum cleaner unattended.
• The power must be turned off during cleaning, maintenance, or when in storage.
• Do not pull the power plug to turn off the vacuum cleaner. Hold the plastic part of the plug to remove it from the power socket.
• The power supply voltage must correspond to that of the vacuum cleaner charging voltage.
• Keep the power cord away from sharp objects to prevent it from being damaged.
• To prevent fires do not immerse the vacuum cleaners in water, do not expose them to any heating appliances;
• Do not drag the power cord when moving the charging station.
• In the case of the below situations do not use the vacuum cleaner and send it immediately to the nearest approved maintenance facility if:
  • The vacuum cleaner fell and consequently damaged
  • The power cord is damaged.
• Stop operating the vacuum cleaner if the suction inlet is blocked to prevent damages (such as overheating) to the motor or deformations to the vacuum plastic part occasioned by overheating motor.

Battery charging signal

1. It may take you a long time for charging under the following circum stances:
   • Room temperature is higher than 30°C;
   • Recharge immediately after the vacuum cleaner has stopped operating.
2. Always recharge the vacuum cleaner after each usage no matter how long it has been used.
3. Unplug when not charging.
4. When not in use for more than two months the vacuum cleaner should be disconnected from the power supply. To ensure a longer service life, the vacuum cleaner must be charged once every two months.
5. The vacuum cleaner or adapter may become hot during charging so take the necessary precautions to avoid contact.

PRODUCT PARTS LIST

PRODUCT SCHEMATIC

LED DISPLAY

• Battery Indicators
• Power Mode Indicators
• Automatic Dust Detection Mode

1. LED Display
2. Power Mode Switch
3. Battery Pack
4. Battery Release Button
5. Anti-Static Column
6. Power Switch
7. Filtration System
8. Dust Box
9. Dust Box Open Button
10. Color Breathing Lamp
11. Dust Box Release Button
12. Main Motor Release Button
13. Retractable Metal Tube
14. Metal Tube Telescopic Adjustment Part
15. Cleaner Brush Release Button
16. Brush Change Button
17. Motorized Cleaner Brush
18. LED Lights

PRODUCT PARAMETERS

ASSEMBLY AND COMBINATIONS

• Install vacuum cleaner in the right direction by a clear sound of click in each step to avoid airflow issues or not working.
• If you want to disassemble the vacuum, just press the release button on each part.

CHARGING

• Please fully charge the battery before your first use as the product is delivered non fully charged for safety.
• Please use the original charger. It takes about 4-4.5 hours to fully charge the battery.
• The vacuum cannot be turned on when charging for safety.

Method 1/ Method 2

• Insert the power plug into the charging port; connect the power adapter with the power supply.

WHEN CHARGING

• Battery indicators show the battery-electric quantity when charging.
• The light will turn off after about an hour when fully charged.
• Color of breathing lamp with different battery-electric quantities when charging:
  • 0-39% shows red
  • 40%-69% shows purple
  • 70%-100% shows blue
• The light will turn off after about an hour when fully charaed.

READY TO USE

POWER SWITCH

• Press the power switch to turn on the vacuum, press twice to turn it off.

POWER MODE SWITCH

Note : It can automatically adjust the suction power based on the level of debris detected by the infrared sensor in AUTO Mode. It may take a few seconds because the dust needs to enter the main motor first to trigger the infrared sensor in the main motor.

LED DISPLAY

• The LED Display will help you clearly see the battery-electric quantities and the power modes.

COLOR BREATHING LAMP

Color of light with different battery-electric quantities when working:

• 100%-70% shows blue
• 69%-40% shows purple

• 39%-0 shows red
• Note: The light shows flashing red while the battery-electric quantity is less than 10%

MAINTENANCE AND CLEANING

EMPTY THE DUST BOX

• Please ensure the amount of the trash is not over the Max Line and empty the trash after each use.

CLEAN STRAINER, CYCLONIC, AND HEPA FILTER

1. Open the dust box, then rotate the strainer to take it out.
2. Press the button, rotate the dust box from to , take off the dust box, then rotate the strainer to take it out.
3. Take out the multi-stage cyclonic separation accessory.
4. Take out the HEPA filter.
5. Wash the strainer and cyclonic with cold water and clean the HEPA filter with the cleaning tool.
6. Ensure the strainer and cyclonic are completely dry before refitting.

FILTER INSTALLATION

1. Correspond to the lock position, install cyclonic to strainer.
2. Put the HEPA into the strainer.
3. Make sure the notch on the dust box fits into the slot perfectly.
4. Rotate the dust box from to .
5. Rotate the strainer to fix it on the main motor.

CHANGE THE ROLLER BRUSH

• The vacuum cleaner comes with two rollers, you could use the specific roller according to your cleaning needs.
• The V rubber brush is more suitable for both the low and med pile carpets and hard floors.
• The soft roller brush is more suitable for hard floors. It can perfectly protect your hardwood floor.

1. Press and hold the button
2. Pull the V rubber brush out
3. Install the soft roller brush

STORAGE

WALL BRACKET INSTALLATION

1. Tear off the tape, attach the wall bracket to the wall.
2. Punch 2 holes in the wall.
3. Insert screws into the plastic case.
4. Nail the wall bracket to the wall with screws.

STORAGE

TROUBLESHOOTING

If the solutions below cannot solve the problem or the issue you met is not listed, please contact us via support@inselife.com

WARRANTY POLICY

NOTE: THIS WARRANTY TERM GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

12-month Warranty & Lifetime Customer Support

• Only apply to eligible purchases made directly from the INSE authorized distributors. Warranty coverage applies to the original owner and to the original product only and is not transferable.

How to initiate a warranty claim

• If your appliance operates improperly while in use under normal household conditions within the warranty period, please contact our customer support [support@inselife.com] to fill out the warranty form to initiate a warranty claim.

Contact

Please do not hesitate to contact us whenever you want, we are always here for you!

• support@inselife.com
• www.inselife.com
• 1-877-220-5188
• (9 a.m. to 6 p.m. Mon-Fri)

General Tips,FAQ,Usage,etc

• https://bit.ly/inse-s9-support

All rights are reserved by INSE.

MADE IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>