Bissell 23159 SpinWave Cordless Hard Floor Expert User Guide

: June 14, 2024
: Bissell

Bissell 23159 SpinWave Cordless Hard Floor Expert

Product Information

The 2307, 2315 Series is a hard surface floor cleaner designed for household use. It comes with various features and accessories to ensure effective cleaning.

Product Features

Handle with digital controls for easy operation
Battery status indicator lights to monitor the power level
Clean water tank for holding the cleaning solution
Low profile foot for reaching under furniture
Power spin pads for efficient cleaning
Spray nozzle for dispensing the cleaning solution
Charging port for recharging the battery
Storage tray for convenient organization

Included Accessories

Charging adapter and plug
Storage tray
Handle
Body of unit
2 Soft Touch Pads
2 Scrubby Pads
2 8oz BISSELL Multi-Surface Formula

Safety Instructions

Before using the product, please read and follow these important safety instructions:

Plastic film can be dangerous, keep it away from children to avoid suffocation.
Turn off the power switch and disconnect the charger plug from the electrical outlet before performing maintenance or troubleshooting checks to reduce the risk of electrical shock.

Product Usage Instructions

Assembly

To assemble the hard surface floor cleaner, follow these steps:

Insert the handle into the body of the unit until you hear a click.

Cleaning Formulas

Use only BISSELL cleaning formulas intended for use with the hard floor device to reduce the risk of fire and electric shock.

The following formulas are recommended:

Multi-Surface Formula: Great for cleaning ALL sealed hard floors.
Wood Floor Formula : Restore your sealed wood floors’ natural shine.

Charging the Battery

Before using the hard surface floor cleaner, make sure to charge the battery following these steps:

Ensure the unit is turned off by checking that the battery status indicator lights are not illuminated.
Insert the charging adapter plug into the charging port on the back, right side of the unit.
Plug the adapter into a suitable wall outlet. The battery status indicator lights will illuminate when charging.
For maximum run time, charge the unit for 4 hours prior to use.
To check the battery status, turn the unit on by pulling the handle back and pressing the power button. The battery is fully charged when all three blue status lights are illuminated.

In-Use LED Display

To prevent overcharging and potential battery damage, charge the unit when there is less than 10% power left (one LED flashing blue).

Battery Status:

100% to 67%: Battery level is high
66% to 33%: Battery level is medium
32% to 10%: Battery level is low
0%: Battery level is critically low, and requires charging

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING YOUR SPINWAVE® CORDLESS.
When using an electrical appliance, basic precautions should be observed, including the following:

WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

Do not use outdoors.
Do not allow it to be used as a toy. Close attention is necessary when used by or near children.
Do not use it for any purpose other than described in this user guide. Use only the manufacturer’s recommended attachments.
Do not charge with a damaged cord or plug. If an appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized service center.
Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
Do not handle chargers, including charger plugs and charger terminals, with wet hands.
Do not put any objects into openings. Do not use any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce airflow.
Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts.
Turn off all controls before plugging or unplugging the appliance.
Use extra care when cleaning on stairs.
Do not use appliances in an enclosed space filled with vapors given off by oil-based paint, paint thinner, some moth-proofing substances, flammable dust, or other explosive or toxic vapors.
Use only BISSELL cleaning formulas intended for use with this appliance to prevent internal component damage.
Do not immerse. Use only on hard floor surfaces moistened by the cleaning process.
Keep the appliance on a level surface.
Do not carry appliances while in use.
Do not charge the unit outdoors.
Use only the charger supplied by the manufacturer to recharge.
Do not incinerate the appliance even if it is severely damaged. The batteries can explode in a fire.
Battery cell leaks can occur under extreme conditions. If battery cell contents come in contact with the skin or eyes: immediately flush with water for 15 minutes. Seek medical attention if irritation persists.
Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specific range may damage the battery and increase the risk of fire.
Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperature above 130°C or 265°F may cause an explosion.
Do not pull or carry by cord, use the cord as a handle, close a door on the cord, or pull the cord around sharp edges or corners. Do not run the appliance over the cord. Keep the cord away from heated surfaces.
WARNING RISK OF INJURY. MOP PADS MAY START UNEXPECTEDLY. UNPLUG BEFORE CLEANING OR SERVICING.

SAVE THESE INSTRUCTIONS

This model is for household use only.
Plastic film can be dangerous. To avoid the danger of suffocation, keep away from children.
To reduce the risk of electrical shock, turn the power switch OFF and disconnect the charger plug from the electrical outlet BEFORE performing maintenance or troubleshooting checks.

Thanks for buying a BISSELL® SpinWave® Cordless

We love to clean and we’re excited to share one of our innovative products with you. We want to make sure your hard surface floor cleaner works as well as it does today for years to come, so this guide has tips on using, maintaining, and if there’s a problem, troubleshooting.
Your cleaner needs a little assembly before getting to work, so flip to the Assembly section on the page, and let’s get started!

What’s In The Box?

NOTE: Standard accessories may vary by model. To identify what should be included with your purchase, please refer to the “Carton Contents” list located on the carton top flap.

Get to Know Your SpinWave® Cordless

Handle
Digital Controls
Battery Status Indicator
Lights Clean
Water Tank
Low Profile Foot
Power Spin Pads
Spray Nozzle
Charging Adapter Plug Storage Tray
Carry Handle
Charging Port

Assembly

WARNING

Do not plug in your SpinWave® Cordless until you are familiar with all instructions and operating procedures.
Insert the handle into the body of the unit until you hear a “click”.

Cleaning Formulas

WARNING

To reduce the risk of fire and electric shock due to internal component damage, use only BISSELL cleaning formulas intended for use with the hard floor device.
Keep plenty of SpinWave® Cordless formulas on hand so you can clean your sealed hard floors whenever it fits your schedule. Always use SpinWave® Cordless formulas in your machine. Other solutions may harm the machine and may void the warranty.

SPIN W A V E ® CORDLESS FORMULAS

Multi-Surface Formula| Wood Floor Formula
|
Great for cleaning ALL sealed hard floors| Restore your sealed wood floors’ natural shine

Charging the Battery

NOTE: On first use, make sure the unit is fully charged before use. To check the battery status, turn the unit ON by pulling the handle back and pressing the power button. The battery is fully charged when all three blue status lights are illuminated.

Use LED Display

WARNING

Overcharging may cause battery damage, fire, or explosion.
Your BISSELL® SpinWave® Cordless machine has an LED light display that will turn on when the power key is pushed to show the battery life status. All LED color is blue.
TIP: Be sure to charge unit when there is less than 10% power left, one LED flashing blue.
NOTE: Keep the temperature range between 40-104 °F when charging the battery, storing unit, or during use.

Attaching Mop Pads

Option 1

Your BISSELL® SpinWave® Cordless may have come with two different mop pads:
The Soft Touch Pad is for everyday use on delicate flooring like sealed hardwoods and laminate.
The Scrubby Pad is used to power through tough, sticky messes.

Your SpinWave® Cordless may have come with mop pads attached. If not, to attach mop pads, carefully lay the machine down on the floor.
The back of the mop pad has a small dot in the center of the pad.
First, fold the pad in half, making sure the cloth material is inside the fold.
Then, with the mop pad folded, line up the small dot in the center of the pad with the middle screw on the bottom of the foot.
Lastly, line up the edge of the mop pad with the inner ring on the foot, attach the mop pad to the hook, and loop material on the bottom of the foot.

Option 2

NOTE: These next steps are to help you apply the mop pads more accurately onto the machine.

Place clean mop pads upside down in the storage tray. The dot on each mop pad should be facing up.
Hover the unit over the mop pads to align in the center, then place the unit down on the mop pads. Now they are attached to the machine.

Filling Your Clean Water Tank

The Clean Water Tank is located on the front of the machine.
Lift the Clean Water Tank straight up to remove it from the machine.
Unscrew the cap from the Clean Water Tank.
- The Clean Water Tank has two measuring volumes depending on the amount of space you would like to clean.
For large area cleaning
- a. Fill the Clean Water Tank with warm tap water to the second water fill line.
- b. Add BISSELL® SpinWave® Cordless formula to the second formula fill line.
- For small area cleaning
- a. Fill the Clean Water Tank with warm tap water to the first water fill line.
- b. Add BISSELL® SpinWave® Cordless formula to the first formula fill line.
Screw the cap back onto the Clean Water Tank.
Slide the Clean Water Tank back into place until you hear a click.

A few notes about filling the Clean Water Tank:

Fill with warm (140°F/60°C MAX) tap water and add the appropriate BISSELL solution. DO NOT USE BOILING WATER. DO NOT HEAT WATER OR TANK IN MICROWAVE.

Cleaning Sealed Hard Floors

ATTENTION: This machine is designed to be used only on sealed hard floors and should not be used on carpets or rugs. For best cleaning results, sweep or vacuum the floor surface prior to using it to avoid scratching or damaging floors from sharp debris.
TIP 1: You may feel a slight vibration when turning on the machine if the mop pads are not aligned correctly. Wait a few seconds for the pads to adjust themselves. If this doesn’t occur, turn the machine OFF and replace the mop pads following the instructions in Attaching Mop Pads” sections.
TIP 2: When you press the ON/OFF button to start the unit the LED lights will illuminate, but the mop pads will not start rotating until the unit is reclined.

When fully charged, press the ON/OFF button and the three LED lights will illuminate.
Recline the body of the unit backward to start the rotating mop pads.
- TIP 3: For optimum cleaning, perform overlapping cleaning strokes while dispensing the cleaning solution. Care should be taken to not overwet the floor surface, especially when cleaning wood and other delicate floor surfaces.
- TIP 4: When cleaning near baseboards, edges, or furniture you may feel a slight pull from the unit due to bouncing off the surface.
To clean, push the SPRAY button to dispense the solution.
The solution will spray out of the nozzle on the front of the foot. You should hear a soft buzzing noise each time you press the SPRAY button to indicate solution is being dispensed.
For more difficult and stuck-on messes, spray the solution directly on the mess and line up one of the mop pads parallel to the mess. Move the mop pad over the mess and slowly move the machine back and forth to clean, continuing to spray the solution as needed.
- NOTE: When finished cleaning, make sure to push the OFF button before standing the machine upright as the mop pads will continue to spin until the machine is turned OFF.
- NOTE: If the unit is on and gets placed in the upright position while still on, the unit will go into standby mode. To power OFF, press the ON/OFF button or the unit will turn off by itself after 10 seconds of no action. You will know it is off when the LED lights are no longer illuminated.
To power OFF the unit, press the unit ON/OFF button and put the unit into an upright position. The LED lights will turn off.

Cleaning Your SpinWave® Cordless

WARNING

Do not set the machine on carpet, rug, or another fabric surface when the mop pad is removed as hook and loop material on foot may damage them.
Do not store the machine on wet mop pads as they may damage wood or other delicate floors.

To remove mop pads, simply pull the pads off the hook and loop material on the bottom of the machine.
Machine wash separately in warm water. Use only liquid detergents. Do not use bleach or fabric softener. Tumble dry on low. Do not iron. Do not dry clean.
Store upright in a storage tray in a dry, protected area until the next use. Since this product uses water, it must not be stored where there is danger of freezing. Store with dry mop pads. Wet mop pads may damage wood and other delicate, sealed hard floors.

NOTE: Any solution remaining in the Clean Water Tank should be emptied prior to machine storage.
NOTE: Store cleaner in a protected, dry area. Since this product uses water, it must not be stored where there is danger of freezing. Freezing may damage internal components and void the warranty.

Disposing the Batteries

This product contains lithium-ion rechargeable batteries. According to Federal and State regulations, removal and proper disposal of lithium-ion batteries is required. For the removal of batteries in your SpinWave® Cordless, see the instructions on this page.
NOTICE: Disconnecting the battery will destroy the appliance and invalidate the warranty.

Before proceeding, ensure that:

The unit is disconnected from the charger.
The Clean Water Tank has been removed from the unit.
You have flat-head and Phillips-head screwdrivers and rubber-handled wire cutters.

Insert a screwdriver into the hole on the back of the unit below the Carry Handle in order to disconnect the handle.
With a Phillips-head screwdriver, remove the 5 screws on the back of the unit.
Insert a flat-head screwdriver between the top front and back plates located between the Carry Handle and main handle to remove the front body plate.
Remove the control panel with the battery pack. For leverage, you may need to use the flat-head screwdriver to help remove.
Disconnect the 8 inputs that are connected to the control panel. Then, using a Phillips- head screwdriver, unscrew the two screws on the control board.
Pull the control panel back from the battery pack. Then, with rubber-handled wire cutters, clip the two metal poles to disconnect the battery pack from the control panel.

NOTE: Keep Battery Pack together – DO NOT separate individual batteries.
For specific disposal instructions for batteries, please contact the RBRC (Rechargeable Battery Recycling Corporation) at 1-800-822-8837 or visit www.Call2Recycle.org.

Troubleshooting

WARNING

To reduce the risk of electric shock, turn the power switch OFF and disconnect the plug from the electrical outlet before performing maintenance or troubleshooting checks.

Problem| Possible causes| Remedies

The unit is vibrating/ wobbling| Mop pads are not aligned with the foot.| Realign the mop pads on the foot.

Reduced spray OR no spray| The clean Water Tank may be empty.| Refill tank.
A clean Water Tank may not be seated completely.| Turn the power OFF.

Remove and Reseat the Tank.

The system isn’t completely primed.| Hold the trigger for 10 to 15 seconds to make sure the solution has flowed to the spray tips.
Not holding the trigger to spray solution.| Hold the trigger continuously while using the machine.
Spray tips on foot clogged.| Turn the power OFF. Use a pin to clean the spray tip located front and center of the machine.
Spin plates are not turning or are wobbling| Mop pads are not installed properly.| Turn the Power OFF and follow the instructions on page 6 for replacing mop pads.
The machine is standing upright.| Recline machine.

Machine is leaking| The Cap of the Clean Water Tank is not closed properly.| Remove the Clean Water Tank and re-apply the cap.

The unit will not charge| The charger plug/cord is not connected.| Make sure the charger plug is completely plugged into a wall outlet and the charging cord is completely plugged into a port on the back of the unit.
Not the correct charger.| Use only the charger that comes with the machine.

All three (3) LED lights flashing| Pads forced to stop spinning, potentially due to stuck debris, compressed under furniture, or being briefly stepped on.| Turn the unit off or wait 10 seconds for the lights and machine to turn OFF. Then, press the ON/OFF to start the unit again.
Heavy and extended usage may cause the internal temperature of the machine to warm up slightly past the typical operating temperature.| Press the power button on the handle one time and wait for the unit to cool down and reset.

Two (2) LED lights flashing| The functional issue with the machine.| Contact us for additional assistance.

Warranty

This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Care by E-mail or telephone as described below.
It may be necessary to obtain some of your personal information, such as a mailing address, to fulfill the terms of this warranty.
Any personal data will be handled pursuant to BISSELL’s Privacy Policy, which can be found online at www.BISSELL.com/privacy-policy.

Limited One-Year Warranty

Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL will repair or replace (with new, refurbished, lightly used, or remanufactured components or products), at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for one year, any defective or malfunctioning part.
See the information below on “If your BISSELL product should require service”.
This warranty applies to products used for personal, and not commercial, or rental, service. This warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the user guide is not covered. This warranty will only be valid if the product is used in the same country in which it was sold.
BISSELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY

THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES, EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES, WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE ONE-YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event of a warranty claim.

Service

If your BISSELL product should require service:

Contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center in your area. If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Care.
Website: www.BISSELL.com/service-centers
E-mail: www.BISSELL.com/email-us

Call:

BISSELL Consumer Care US Consumers 1-800-237-7691 Canada Consumers 1-800-263-2533 Monday – Friday 8 am – 10 pm ET Saturday 9 am – 8 pm ET Sunday 10 am – 7 pm ET

Please do not return this product to the store

Other maintenance or services not included in the manual should be performed by an authorized service representative.
For any questions or concerns, BISSELL is happy to be of service.
Contact us directly: US Consumers 1-800-237-7691 Canada Consumers 1-800-263-2533.

Register your product today!

Registering is quick, and easy and offers you benefits over the lifetime of your product.

You’ll receive:

BISSELL Rewards Points
Automatically earn points for discounts and free shipping on future purchases.

Faster Service

Supplying your information now saves you time should you need to contact us with questions regarding your product.

Product Support Reminders and Alerts

We’ll contact you with any important product maintenance reminders and alerts.

Special Promotions

Optional: Register your email to receive notice of offers, contests, cleaning tips, and more!
Visit www.BISSELL.com/registration!
Visit the BISSELL website: www.BISSELL.com
When contacting BISSELL, have the model number of the cleaner available.
Please record your Model Number :———————————–
Please record your Purchase Date: ————————————
NOTE: Please keep your original sales receipt. It provides proof of purchase date in the event of a warranty claim.
See the Warranty page for details.

Parts & Supplies

For Parts and Supplies, go to www.BISSELL.com and enter your model number in the search field.
We can’t wait to hear from you!
Rate this product and let us (and millions of your closest friends) know what you think! www.BISSELL.com
©2018 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China Part Number 161-7187 07/18
Visit our website at: www.BISSELL.com

Documents / Resources

| Bissell 23159 SpinWave Cordless Hard Floor Expert [pdf] User Guide
23159 SpinWave Cordless Hard Floor Expert, 23159, SpinWave Cordless Hard Floor Expert, Cordless Hard Floor Expert, Hard Floor Expert, Floor Expert
---|---