SHARGEEK 100 Power Bank User Manual

: June 15, 2024
: SHARGEEK

Table of Contents

SHARGEEK 100 Power Bank
Specifications
Important Safety Notes
FCC Statement
Battery Information
Customer Service
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

SHARGR-LOGO

SHARGEEK 100 Power Bank

SHARGEEK-100-Power-Bank-product

Specifications

Name: Shargeek 100 Power Bank
Model: STM2-2
Output Port: 2 X USB-C +USB-A+DC
Battery Cell: 18650 Lithium-ion
Typical Capacity: 25,S00mAh/93.SWh 3.65V
Rated Capacity: 15,000mAh (5V~3A)
Dimension: 151X59X46mm
Weight: “‘580g
USB-Cl Input: 5V/9V/12V/15V-3A, 20V-5A
DC Input: 5-24V-3A
DC Output: 3.3-25.2V-3A
USB-Cl Output: 5V/9V/12V/15V-3A, 20V-5A (l00W Max)
USB-C2 Output: 5V/9V-3A, 12V-2.5A, 15V-2A(30W Max)
USB-A Output: 5V-3A, 9V-2A, 12V-l.5A
DC+USB-C2 Output: SSW+30W
DC +USB-A Output: SSW+ 18W
USB-Cl +USB-C2 Output: SSW+ 30W
USB-Cl +USB-A Output: SSW+ 18W
USB-C2+USB-A Output: SV~SA
DC +USB-C2+USB-A Output: SSW+SV-SA
USB-Cl +USB-C2+USB-A Output: 65W+SV-5A
Conversion Efficiency: ~70%
Package List: PowerbankX 1, User manualXl,cableXl, Carrying bagXl

Important Safety Notes

Declaration of Conformity
Hereby, SHARGE declares that the product type STM2-2 is in compliance
with Directive 2014/30/EU.

FCC Statement

This device complies with Part 15 ofthe FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communicationsHowever, there isno guarantee that interference will not occur in aparticular installation.If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.

Terms Introduction

EMOS: Energy Management OS is a patented operating system used for power supply management, developed by SHARGE R&D team.
Voltage Unit: VI Current Unit: A I Power Unit: WI Temperature Unit: •c
Short-press: Press and release immediately.
Long-press: Press and hold for more than 2 seconds, and then release.

Top-level GUI Introduction

The top-level GUI includes 5 different sections. Each section is described as below

Port Status
This section shows the connected port information, which be can either USB-C1 , USB-C2 , USB-A , DC-IN or DC-OUT , .

Input Status
This section shows the input information when the product is being charged. The input information includes charging voltage (such as ), charging current (such as ), charging power, and charging port (this product can be charged via USB-C and DC). The charging port is also shown as .

Output Status
This section shows the output information when the product is charging other devices. The output information includes output voltage (such as ), output current (such as ) and the output power of specific port. The output port could either be USB-C, USB-A, ROLL, or TOTAL, shown as below:

Only when the product is charging multiple devices, can the shown icon be changed by short-pressing the button.

Note:
When ROLL is shown, each port’s output status will be shown in turn. When TOTAL is shown, total output power will be shown. 04. Battery Information
This section shows current status of the battery, including batter life, battery voltage, and real-time current. Note thatthe battery life icon is designed with different colors based on different battery level, shown as battery level percentage (e.g. 30 means 30%). The icon color is defined as below:

System Status
System status shows the battery temperature (with the icon ) ), the circuit board temeperature (with the icon ), and the system running time.

Second-Level GUI Introduction

Long-pressing the main button (when the system is in the top-level GUI)
will enter the second-level GUI, with options below:

Configure DC output parameters
Detail information on the battery pack
Configure temperature unit
Reset system running time
Configure display settings
System power off
Exit (back to top-level GUI)

You can enter the above options by long-pressing the button when the corresponding icon is flashing. After entering the options, you may short- press to select options and long-press to change parameters.

Configure DC Output
You can configure the DC output voltage via either coarse- or fine tuning, with O.lV as the minimal adjustment unit. Once finishing the voltage configuration, you may turn on DC output.

Battery Information

This section contains detailed information on the battery pack. It shows voltage of each battery cell, remaining battery capacity (estimated by thecoulometer based on the last fully-discharged capacity), battery cycles, and the estimated battery life.
Note that the remaining battery capacity varies based on different discharging power. The coulometerwill record charging/discharging power, count battery cycles, and estimate battery life.

Temperature Unit Configuration

You can configure the temperature unit between celsius (0 C) and fahrenheit (‘F).

System Running Time Reset

You can reset system running time to recalculate the charging time for specific devices.

Display Configuration
You can modify the display sleep time between 1MIN and 2MIN , disable sleep function, or change the display direction to or

System Power Off
Turn off the system to save power, especially when you are not intended to use it fora long period of time.

Return to Top-Level GUI
Once you finish the configuration or information checking, you can return to top-level GUI by long-pressing EXIT .

Warning

EMOS owns a complete, strict policy to ensure the user safety.
Users must fully understand each warning message, including:

DC Output Warning
Circuit Over-Temperature Warning
Low Energy Warning
Battery Over-Temperature Warning
Battery Low-Temperature Warning

We designed a message box for each warning information.

DC Output Warning
If the product has a DC output port, and when the user turns on DC output, the screen will pop out the message below:

WARNING
Do not plug in any INPUT device when DC OUTPUT is switched on.
Long press to confirm.

Circuit Over-Temperature Warning
The circuit board will generate heat during power conversion. When the temperature exceeds ao0c, over-temperature protection will be triggered, and the screen will pop out the message below.

CIRCUIT TEMP HIGH

Long press to quit.

Low Energy Warning
When the the battery voltage is lower than pre-defined threshold (for Lithium- ion cells combined in series of 4, the threshold voltageis 11.6V), the screen will pop out the message below.

LOW ENERGY
Long press to quit.

Battery Over-Temperature Warning
Battery is very sensitive to environment temperature, and extreme temperature will affect the performance of battery cells, with battery life declined and possbile permanent damage. When the battery temperature is above 60°C, over- temperature protection will be triggered and the system will turn off outputs.

In this situation, please turn off the system if applicable and let the product cool down.

BATTERY TEMP HIGH
Long press to quit.

Battery Low-Temperature Warning
When you are using the product with EMOS in cold areas, the battery may be too cold (below -15°C) to provide sufficient power. EMOS will also turn off the system output to avoid unstable output power. Please put the product in a warm environment to recover.

BATTERY TEMP LOW
Long press to quit.

NOTE:
SHARGE reserve the rights to change this manual based on actual products without notifications, please contact us via email (info@sharge.com) if you have any questions

Customer Service

12-month Limited Warranty
Lifetime Customer Support
Reach us here: info@sharge.com.

NOTE
Please note that your rights under applicable law governing the sale of consumer goods remain unaffected by the warranties given in this Limited Warranty. The warranty can either be Refund, Replacement or Repair based on different situations
The warranty does not cover defects or damages caused by accident, improper care, improper use, negligence or excessiveware and tear. SHARGE warrants that this product is free from defects in material and workmanship for a period of 12 months from the date of purchase.

Follow us on:

Join Our Discord