BROMIC bh3623002 Eclipse Master Remote Dimmer Controller And Portable Heater User Guide
- June 15, 2024
- Bromic
Table of Contents
Programming the Eclipse Master
Remote for use with the Eclipse Dimmer Controller & Eclipse Portable
Heater
Troubleshooting Guide
bh3623002 Eclipse Master Remote Dimmer Controller And Portable Heater
Bromic Eclipse Master Remote
• US – BH3623002-1
• AU – 2620662-1
• EU – BH4623003-1| Bromic Eclipse Dimmer Remote
• US – BH3230007-1
• AU – 2620637-1
• EU – BH3230017-1| Bromic Eclipse Portable
• US – BH0820001-1
• AU – 2620611-1
• EU – BH0820011
REQUIREMENTS
The Master Remote features 6 zones as indicated by the red led lights at the
top of the remote. Each zone can be programmed to control a single dimmer or
multiple dimmers.
You will need to be in close proximity to the dimmer control and/or portable
unit to be able to hear the audible beeps of the controls during the
programming process. You do not need to open the units themselves.
You will need the individual standard remotes for this process along with the
new master remote.
The original individual remotes can be stored to be used as back up. We
recommend labeling the remotes to the corresponding dimmers for future
refence.
Below are the basic steps for programming an Eclipse Master Remote for use
with the Eclipse Dimmer Controller and Eclipse Portable outdoor heater.
-
To begin you will need to confirm the compatibility.
Turn the Eclipse Standard Dimmer Remote and the Eclipse Master Remote over and confirm they have the same frequency (916 each) listed on the back label. -
Select a zone on the 42-channel remote: Zone 1-6
Press the left or right button under the red led lights to select the desired zone. The buttons will move the selection left or right.6
Once selected the LED will go out but the zone will be remembered during the programming process.
You can program multiple remotes to a single zone or change zones for each remote. It is recommended that you confirm the desired zone before each remote is programming to ensure the remotes are zoned as planned. -
Paring the Heater Functions
Locate the P3 button on the back of the standard remote. Using a paper clip, press the P3 button. You will hear a continuous beep. Turn the remote over and press the top heat button (100%).
Press the corresponding top heat button (100%) on the master remote. You will hear an intermittent beep. The heat functions are now paired.
The programming has been completed for this dimmer. -
Paring the Light Functions
Locate the P3 button on the back of the standard remote. Using a paper clip, press the P3 button. You will hear a continuous beep. Turn the remote over and press the top light button (100%).
Press the corresponding top light button (100%) on the master remote. You will hear an intermittent beep. The light functions are now paired.
The programming has been completed for this dimmer. -
You can now add additional dimmers to the selected zone to create a group of dimmers or change the zone for individual dimmer control.
Repeat steps 3 & 4 listed above for each standard remote to be paired to the
master remote.
We recommend labeling the standard remotes to match the dimmers and zones for
future reference.
If this does not resolve the issue, you will need to schedule a
troubleshooting call with Bromic Tech Support. When contacting our Tech Team
we request you submit model numbers of the heaters and controls, photos of the
installed products and installation wiring along with proof of purchase to
validate any warranty. Please remember to request service calls 48 hours in
advance to ensure availability.
North America – Technical Support
800-301-1293
www.bromic.com
Austrailia – Technical Support
1300 276 642
www.bromic.com.au
Europe – Technical Support
+31 737041029
www.bromic.co.uk
Bromic.com
References
- Luxury Commercial & Residential Outdoor Heaters | Bromic Heating USA
- Bromic Heating United Kingdom - Global Leader In Outdoor Patio Heaters
- Luxury Commercial & Residential Outdoor Heaters | Bromic Heating USA
- Luxury Commercial & Residential Outdoor Heaters | Bromic Heating Australia