NEC KT-RC3 Remote Control Kit User Manual

KT-RC3
Setup manual

Remote control kit

Contents

• Wireless Remote Control
• AAA Batteries x 2
• Sensor unit
• Stereo mini plug cable
• Screw x 2
• Setup manual
• Spacer
• Both-sided tape

Connection

NOTE: Check the connector’s orientation. Match the curved surface of connector to the front side of sensor unit.

1. Turn off the monitor’s main power switch.

2. Connect monitor’s Remote IN connector to sensor unit’s connector using the attached stereo mini plug cable.
   Sensor part of the sensor unit is detachable.
   To connect the stereo mini plug cable from the opposite direction, remove the sensor part and turn it upside down. To remove the sensor part, change the angle of the sensor part while pushing both sides (F) outwards in the direction of the arrows so that it is parallel to the unit bottom surface. Align the sensor part axis (D) with the opening (E) on the unit side, and push the sensor part out of the unit.

3. After installing the sensor unit, adjust the angle. If necessary, fix it with the attached screws. If using a spacer, match the sensor unit’s rear bottom (A) and spacer’s bottom front (B), then slide in the direction of (C). After fixing the spacer, attach to the LCD display.

CAUTION

• Before connect / disconnect stereo mini plug cable, turn off the main power switch of monitor.

• Do not place any heavy objects on the stereo mini plug cable. Do not bend, crimp or otherwise damage the stereo mini plug cable.

• Follow the safety instructions and remote control explanation in the monitor’s User’s manual.

• Refer monitor’s user’s manual for remote control explanation. The action of the attached remote control button depends on the model or optional equipment. For detail information, please contact your supplier.

• The sensor operation may become unstable due to the reflection of external light etc.

• Make sure not to vibrate the sensor unit during use.

• The sensor unit can be installed to any of the four sides (upper, bottom, right, left) of the monitor.
  However, it cannot be installed to the bottom of 65-inch or smaller monitors. Refer monitor’s user’s manual and caution sheet for installing.

• During the installation, be sure to secure the part with the supplied screws, or to fix it to the bottom surface with both-sided tape.

• When adjusting the angle or mounting, make sure not to pinch your fingers.

For supported model, contact your dealer

Cable information
CAUTION:
Use the provided specified cables with this product so as not to interfere with radio and television reception.
Use of other cables and adapters may cause interference with radio and television reception.

Specifications (KT-RC3)

• Depending on the model, the human sensor function may not activate. For detail information, please contact your supplier.

Disposing of your used product: In the European Union
** EU-wide legislation as implemented in each Member State requires that used electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste. This includes the remote control kit or electrical accessory, such as stereo mini plug cable. When you dispose of such products, please follow the guidance of your local authority or ask the shop where you purchased the product, or if applicable, follow applicable legislation or agreement you may have. The mark on electrical and electronic products may only apply to the current European Union Member States.
Outside the European Union
If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority and ask for the correct method of disposal.
For EU:** The crossed-out wheeled bin implies that used batteries should not be put to the general household waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in accordance with legislation.
According to EU directive 2006/66/EC and amendments, the battery can’t be disposed improperly. The battery shall be separated to collect by local service.

FCC Information

WARNING:
The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by Sharp NEC Display Solutions of America, Inc. in this manual. Failure to comply with this government regulation could void your right to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.
The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.

SUPPLIER’S DECLARATION OF CONFORMITY
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

U.S. Responsible Party: NEC Display Solutions of America, Inc.
Address: 3250 Lacey Rd, Ste 500
Downers Grove, IL 60515
Tel. No.: 630-467-3000
Type of Product: Remote control kit
Equipment Classification: Class B Peripheral
Model: Remote control kit (KT-RC3)

Data is subject to change without notice.
Printed in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>