ECOFLOW Porcelain Be Dry Pedestal Instruction Manual

: June 13, 2024
: ECOFLOW

Table of Contents

Porcelain Be Dry Pedestal
Items provided
Tools required
Operation
Urine Diverter Hose Outlet Options
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

Porcelain Pasadero Pedestal
Installation Instructions
FLOOR TEMP LATE
FT-PAS.201021

Porcelain Be Dry Pedestal

Mounting Bracket Location.
Brackets supplied. Please check the location before mounting the bracket as the pedestal is man made.

PLACE PAPER EDGE ALONG WALL

Mounting Bracket Location.
Brackets supplied. Please check the location before mounting the bracket as the pedestal is man made.

ECOFLOW Porcelain Be Dry Pedestal - Figure 1

NOTE Porcelain Pedestal = approx. 210mm from the wall to the centre of the chute.
Overall footprint of pedestal = 445mm x 300mm.

FRONT OF PORCELAIN PASADERO

Items provided

• Pedestal, seat and lid
• Sullage hose
• Metal clamp
• Floor template| • T-piece
• 2x mounting brackets
• 2x anchors
• 2x metal washers| • 2x mounting bracket screws
• 2x mounting pedestal screws
• 2x plastic washers
• 2x screw caps
---|---|---

Tools required

• Jigsaw
• Power drill
• Masonry and brad point drill bits
• Hole-saw drill bit ø5cm| • Short flathead screwdriver
• Philips screwdriver
• Measuring tape
• Sticky tape| • Marker
• Silicone/caulk gun
---|---|---

Steps

Find the best location and position for the pedestal using the Porcelain Pasadero Floor Template provided, then tape the template down. Cut out the hole for the waste chute with a jigsaw. Insert the waste chute into the hole. Place the composting chamber without its lid under the chute to see if the chute needs to be shortened. If so, mark it then cut it with a jigsaw. (This step is demonstrated in Ecoflo’s Porcelain Palisade Pedestal Installation Video)
Cut out the smaller hole shown on the floor template for the sullage hose using a hole-saw or jigsaw.
Place the mounting brackets within their matching locations on the floor template making sure they line up with the holes on the sides of the pedestal. Drill holes through the brackets into the floor for the anchors. Remove the floor template, insert the anchors, screw down the mounting bracket screws and metal washers until brackets are secured (refer to figure 1).
Hook the metal clamp around one end of the sullage hose.
Connect the same hose end to the urine-diverting hole within the pedestal.
Using a flathead screwdriver, tighten the clamp until the connection is firm and secure.
Insert the rest of the hose down the small floor hole.
Bring the pedestal into position over the waste chute and mounting brackets. Silicone may be applied around the base of the pedestal to add cushion and support on uneven surfaces.
Drill the mounting pedestal screws with the plastic washers through the holes on the sides of the pedestal into the mounting brackets. Tighten with a manual screwdriver as using a drill could damage the porcelain. Place the screw caps over the mounting pedestal screws (refer to Figure 1).
Attach the seat and lid to the pedestal by the connection points.
The sullage hose can be lead all the way into the absorption trench or into a collection bottle (not provided). Or, it can be connected to the composting chamber’s excess liquid hose using a T-piece (provided). Refer to diagrams on the next page.

Operation

Always be seated when using a urine separating toilet. Standing could cause urine to splash out of the pedestal.
Pour a cup of water into the urine bowl after each use, or weekly with boiling/hot water.
Close the toilet lid after each use.

ECOFLOW Porcelain Be Dry Pedestal - Figure 3

Urine Diverter Hose Outlet Options

Option 1:
Urine diverter hose →Absorption trench
Option 2:
Urine diverter hose →Collection bottle (not provided)
Option 3:
Urine diverter hose → Chamber excess liquid hose (using T-piece provided) → Absorption trench

ECOFLOW Porcelain Be Dry Pedestal - Figure 4