SIDE- POWER BC-1224-10 Charger User Manual

BC-1224-10 Charger Manual

FEATURES

• Microcontroller based 4-Stage 3-Level adaptive charging
• Fully automatic without intervention
• DC input for charging 24V batteries
• Auto power on/off depended on input voltage
• Output short circuit protection
• Input low voltage and high voltage protections
• Informative panel LED indications

SPECIFICATIONS

Power Off at 12.5V (+1-2%)
Input Fuse| 40A
Protections| Input Polarity| Yes
Low Input Voltage| < 9.5 V
High Input Voltage| > I5_5V
Over Temperature| Internal 80 °C
Output Short Circuit| Yes
Cooling| Controlled DC Fan
Operating Temperature| 0 — 55 °C
Dimensions(mm)| 200 (W) x 205 (L) x 70 (H)
Weight| 1.5Kg

INSTALLATION & MOUNTING

**** Mount the charger such that there is no blocking of the ventilation holes at the rear panel
Ensure the charger is mount securely
Do not install the charger near any heat source or direct sunlight and water
Use sufficient gauge size cables for both input and output
Always fasten cables securely
Ensure good ventilation

OPERATION

| Tickle Charge Red LED
---|---
| Bulk Charge Red LED
| Over Charge Yellow LED
| Float Charge Green LED
| “+” Red Output Binding Post
| “-” Black Output Binding Post |
| Ventilation Holes (Fan Behind)
| DC12V “-” Input Terminal
| DC 12V “+” Input Terminal
| Blade Type Car Fuse Holder

1. Connect DC 12V to the terminal on the rear panel (Cable size should be at least AWG#12 for full capacity operation)
2. Charger turns on when the input voltage is above 13.5V and it turns off when the input voltage is below 12 5V,
3. Pane LEDs flash in cyclic manner (standby state) after power on.
4. Connect the battery to the charger. The charger detects and charges the battery according to the charging condition of the battery automatically
5. Buzzer sounds whenever there is a change in status or alar or alarm.
6. Charging is finished at float charge (green LED flashes).

INDICATIONS

Charaing Status LEDs

All alarms and protections are auto resume

REMEDIES

No indicator is on or they are not in
standby cyclic mode after power on| (1)Check fuse.
(2)Check input power cable connection (3)Need repairing..
Input low/high voltage alarm when power on| Check the input voltage range.
Charger is still in standby mode even the battery has been connected| (1)Check the cables. (2) Faulty batten’.
I Always low input voltage alarm when the charge at bulk charge mode| ( I ) Check the stability of the DC input source during charging process.
(2) Usc large gauge size input cable.
After battery is connected, Trickle & Bulk LEDs flash in cyclic mode for a while and low/high battery alarm rises| Check the battery voltage
After battery is connected, Trickle & Bulk LEDs flash in cyclic mode for a long time. Or It always jumps back to Trickle LED from 0 or F repeatedly| Aged battery with very large leakage current. Need to change the battery.
The charger always jumps back from float charge to bulk charge after it stays at float charge for some time| (I) The leakage current of the battery is large. (2) Check if there is any loading on the battery.
The charger jumps to float charge after a discharged battery is connected| Aged battery with large internal resistance. Need to change the battery.
No flashing LED or only one LED is on| There is always at least one LED flashing. Otherwise the charger needs repairing.

Confidence by Control
SIDE-POWER.com
This document may contain typographical errors, to which
Sleipner Motor assumes no responsibility.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>