dib Daewon W1500R Toilet Bidet Seat User Guide

dib Daewon W1500R Toilet Bidet Seat User Guide

IMPORTANT SAFETYGUARDS

When using electrical products, especially when children are present, basic safety precautions should always be followed.

READ ALL INSTRUCTIONS BEFORE USING

• For 120V 60Hz : Power supply must be a 15 Amp GFCI outlet.
• The electrical cord must be connected to a GFCI outlet.
• The GFCI outlet should be ift. above the floor.
• Install only in well-ventilated areas to avoid excess humidity.
• Do not install in narrow toilet stalls or in shower stalls.
• Install only where direct contact with water is minimized.
• Do not install near any heat source.
• Avoid using extension cords if possible. Consult with a certified electrician where extension cords are necessary.

DANGER — To reduce the risk of electrocution:

• Do not use while bathing.
• Do not place or store product where it can fall or be pulled into a tub or sink.
• Do not place in or drop into water or other liquid.
• Do not reach for a product that has fallen into water. Unplug immediately.

WARNING — To reduce the risk of burns, electrocution, fire or injury to persons:

• Close supervision is necessary when this product is used by, on, or near children or handicapped individuals.
• Use this product only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
• Never operate this product if it has a damaged cord or plug, if it is not working properly, has been dropped or damaged, or dipped into water. Return the product to a service center for examination and repair.
• Keep the cord away from heated surfaces.
• Never drop or insert any object into any opening or hose.
• Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
• Connect this product to a properly grounded outlet only. See grounding instructions.
• Unplug this product before filling. Fill (reservoir) with water only.
  
  

Parts & Configuration

Operation Remote Control

Main Body

1. Cover
2. Touch key
3. Bidet Nozzle
4. Seat sensor
5. Product release lever
6. Deodorizer
7. Deodorization inlet
8. Catch plate
9. Water Inlet with mesh filter
10. Night light
11. Power plug

Accessories

Installation & Trail Operation

Remove the seat from the existing toilet body.

• Release the nuts, and then remove the seat and cove from it.
• Keep the removed seat, cover and nuts in a proper place in case of using them again.
• Turn off the water.

Remove the water hose and then install T-valve.

Fix the bracket onto the toilet first.

• Adjust the seat and the front part of toilet back and forth so that they can correspond with before fastening the nuts.

**Push the main body toward the bracket completely.

**

• Push it in until it sounds ‘click’
• When the product is not installed well, it may cause seat apart.

After installing the T-valve, connect the bidet-use hose to the bidet body and turn on the water.

Insert the deodorizing cartridge into the bidet body.

**Turn on the water and check for leaks.

**

Be sure that the nozzle comes out and retracts when powered on.

• Don’t plug the power cord with wet hands. Risk of electric shock.

How to Use

1. Sit on the toilet seat

   • Be sure to sit on the seat sensor. If the sensor is not occupied, all functions will not operate.
   • Deodorization starts automatically.

2. Wash, Bidet, Intensive

   • Selected function can be used as described.
   • When pressing the selected function again, nozzle will move back and forth to wash a wider range.
   • Press the button once again to stop Massage function.
   • dib’s specialized water spray in Intensive function helps relieve constipation and fecal stasis.

3. Dry Temperature Control

   • Dryer operates for 3 minutes.
   • Dryer temperature is adjustable by pressing power ctrl buttons. (5 levels)
   • Dryer effect will be improved if you wipe the moisture lightly before operating the drying function.

4. Pulse

   • When pressing the Pulse button during the operation of Wash, Bidet, and Intensive, water pressure will repeat high and low for smooth pulsating wash.
   • Pulse function will not operate during the operation of Sitz bath.
     *See how to use section 5-14 for Sitz bath.

5. Nozzle Position Control

   • Nozzle position is adjustable. (5 levels)

6. Water Pressure Control

   • Water pressure is adjustable. (5 levels)
   • If the water or screen filters become blocked, it may cause low water pressure. Regularly check the screen filter.

7. Stop

8. All operations will stop.

9. When pressing the Stop button for 3 seconds, the unit will be in sleep mode.

10. Press Stop, Wash, Bidet or Intensive to turn on.

11. When pressing the Stop button for 5 seconds consecutively, the unit will be turned off and on automatically and initialized. All presets will be deleted.

12. Child Function

    • When selecting Child function, settings* will be adjusted for children.
    • 1 min Bidet – 30 sec Bidet Oscillating – 30 sec Bidet Pulse – 2 min Dry work consecutively.
    • In case of DIB-C410, Dry function will not operate.
      * Settings
      Extra extended nozzle position
      Lower water pressure
      Lower seat temperature
      Lower water temperature

13. Seat / Water Temperature Control

    • Seat Water temperature is adjustable. (4 levels) (Off — Low — Middle — High)
    • To reduce the chance of low temperature burns, the seat has a seat heather auto adjustment function which turns to low temperature (35°C, 95°F) when seat is occupied for more than 15 minutes consecutively. If the seat is set lower than middle level, the seat remain at off or low level.

14. Energy Saving FuNction

    • Automatic energy saving moor.
    • This mode will be activated by pressing the Energy Saving button until yellow LED lamp light on. (Seat and water temperature will be kept at 32°C)
    • Powerful energy saving mode
    • This mode will be activated by pressing the Energy Saving button until green LED lamp lights on. (Seat and water heater will be kept off)
    • Release of energy saving mode
    • Press the Energy Saving button until LED lamp turns off.
    • When the unit is occupied, it adjusts to the preset temperature and it returns to the saving mode when seat is unoccupied.
    • If the seat and water temperature are off, they will remain off.

15. Nozzle Cleaning

    • When selecting Nozzle Cleaning while not seated, the nozzle cleans itself 3 times. Then nozzle extends and stop for manual cleaning process.
    • Clean the nozzle with a brush and press STOP button after completion of manual cleaning. Then nozzle cleans itself for 3 times and retracts.
    • NOZZLE CLEANING will not operate if the seat sensor is activated.

16. Deodorization

    • When sitting on the seat, deodorizing function starts automatically.
    • After leaving the seat, the deodorizing function operates for 1 additional minute.
    • Automatic start deodorizing function can be cancelled /set by pressing Stop and Energy saving buttons for 3 seconds.

17. Automatic tank draining

    • To protect water contamination, the water tank will be drained(replaced) for 2 minutes if the seat is not used for 48 consecutive hours.
    • This feature is deactivated from the factory. To activate this feature, press Stop and Water Temp. buttons for 3 seconds.
      More than 3 Seconds

18. Sitz Bath

    • Wash or Bidet is switched to Wash Sitz Bath or Bidet Sitz Bath if Nozzle Cleaning button is selected during Wash or Bidet operation.
    • Water pressure is switched to 1st level regardless of preset water pressure settings and Sitz Bath operates for 5 minutes.
    • LED of Nozzle Cleaning turns on during the operation of Sitz Bath.
    • Select the Nozzle Cleaning again to switch to normal Wash or Bidet.

19. Seat Sensor Release

    • The seat sensor can be activated and deactivated by pressing Pulse button for 3 seconds.
    • If the seat sensor is deactivated, the unit works without occupying the seat and features* cannot be controlled.
      * Features
      Night light, Silent mode, Nozzle cleaning.

20. Night Light

    • Blue LED night light provides enough brightness to see the toilet without turning on the bathroom light.
    • Night light can be turned on and off by pressing 1+1 for 3 seconds while not seated.
    • Night light setting cannot be adjusted if seat sensor release feature is  activated.

Maintenance & Cleaning

Screen Filter Cleaning

1. Close the water valve.
2. Disconnect the water supply hose. Take the screen filter out and clean it with a soft brush.
3. Return the filter after cleaning and reconnect the water supply hose. Open the water valve.

Maintenance during Winter Season
When bidet seat is not used for an extended period of time, unplug and drain the unit.

Cleaning the Unit

1. Exterior surface of unit is made of plastic material, which may be damaged by scrubber, chemicals, etc.
2. Wipe the surface with a soft damp cloth. Do not spray water directly onto the surface.
3. Clean the body after removing the power plug from the outlet. Be sure no water splashes into the power plug or outlet.
4. Be careful of not dropping any chemical detergents or toilet cleaner on the water supply hose. Risk of hose damage.

Draining of Remaining Water

1. Remove the power plug from the outlet.
2. Close the water feed valve.
3. Press the lever plate and gently pull to remove the unit from the catch plate.
4. Use a coin to open the drain plug.

Settings

• : Seat sensor ‘off’ status
• : Seat sensor ‘on’ status
• : Regardless of on/off

No

| Function| Seat oaths| Switch operation| Description|

Initial
stabs

---|---|---|---|---|---
1| Silent mode| | ” — “for longer than 3 seconds.| To turn on/off the operating chime sound,| ON
2| Factory
default setting| | ” “for longer than 5 seconds.| All settings will be initialized.

|
3| Sleep mode| | ” “for longer than 3 seconds.| The unit will be in sleep mode. Press any of ” ” ” and ” ” turn on.

|
4| Seat sensor
release| | ” “for longer than  3 seconds.| Seat sensor feature will be deactivated.| OFF
5| Automatic start
deodorizing| | ” “for longer than 3 seconds.| Automatic deodorizing start feature will be deactivated.| ON
6| Night light| | ” + “for longer than 3 seconds.| To on/off the night light.| ON
7| Automatic
tank draining| | ” “+ ” ”
for longer than 3 seconds| Automatic tank draining feature will be activated| OFF

• The unit will work without sitting on the seat if the occupied seat sensor is deactivated. (turned off)
• If the seat sensor is deactivated, some features cannot be controlled. (Night light on/off, silent mode on/off and nozzle cleaning)
• Above features are deactivated with 1 buzzer sound and activated with 2 buzzer sounds.

Troubleshooting

Please check the following points before requesting the repair service.

Problem

|

Check list

---|---
Completely out of order|

• Check if the power plug is not connected.
• Check if the power supply or outlet failure.

Water does not spray out|

• Check if the water supply is turn on.
• Check if water valve is locked.
• Check if nozzle is blocked by foreign material.
• Check if connection hose is bent.

Water pressure is low|

• Check if screen filter is blocked by foreign material.
• Check if the water pressure is set at too low level.

Water is not warm enough|

• Check if its temperature is set at off or low level, or economy mode.

Seat is not warm enough|

• Check if its temperature is set at off or low level, or economy mode.

LEDs of water high, middle and low level blinking|

• Check the water is supplied properly.
• Power plug out and in process required after checking.

Water tank is drained intermittently|

• Check if the automatic water draining feature activates.

Self-Diagnosis Table

* Please refer to the following table and inform the exact status when requesting repair service.

No

| Self Diagnosis|

Indication

---|---|---
1| Water temp sensor is disconnected or not inserted| LEDs of water low

• middle level blinking
  2| Water temp sensor is short-circuited or overheated| LEDs of water high — middle level blinking
  3| Seat temp sensor is disconnected or not inserted| LED of water low level blinking
  4| Seat temp sensor is short-circuited or overheated| LED of water high level blinking
  5| Check the water is supplied properly.| LEDs of water high, middle and low level blinking Power plug out and in process required after checking.

USA: Federal Communications Commission (FCC) statement

This device complies with part 15 of the FCC Rules, Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Warning

This equipment has been tested and found to comply with the limit for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Canada: Industry Canada (IC) statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Item

|

Electronic bidet seat [01B-NE850Fll

---|---
Rated voltage| 120V / 60Hz
Max. Power consumption| 1330W
Power cord length| 1.5M
Water feed method| Directly connected to water pipe
Recommended water inlet pressure| 0.7-7.5kgf / cm2
Wash| Feed Volume| Wash| 0.7 Q / min
Bidet| 0.7 Q / min
1   Intensive| 0.9 Q/ min
Pressure control| Wash/Bidet 10 Levels. Intensive 5 levels
Temperature control| 4 levels (off-low-middle-high)
Heater capacity| 1.300W
Safety device| Temp.Fuse. Thermo Switch
Heated seat| Temperature control| 4 levels (off-low-middle-high)
Heater capacity| 38W
Safety device| Ternp.Fuse
Dry| Temperature control| 5 levels
Heater capacity| 400W
Safety device| Temp.Fuse, Bi-metal
Deodorization| Catalytic deodorization
Feed water temp. tolerance range| 3-35t(recommened 12–35t)
Usage room temp. tolerance range| 3-40t(recommened 10-35t)
Dimension Elongated| 450mm X 528mm X 112mm
Weight Net weight (Gross weight)| 4 Okg(7 Okg)
Remote control| RF remote control for an electronic bidet seat [01B- LT2-RH
---|---
Static current| ≤ 15LA
Operating current| ≤ 30.4
Transmission protocol| 2.44 a wireless transmission
Transmission distance| ≤10m
Running duration| With three alkaline AM batteries, the Controller can run for 11 months (Under the condition of using 40 the
Color| Gray / Blue / White
Dimensions| L x W x H: 177mm x 55mm x 18mm
Number of buttons| 15
Button lifespan| Front buttons ≥ 100,000 times / Side buttons ≥ 100,000 times
Weight| 75g
Operating temperature| 0°C-+40°C
Storage temperature range| 0°C-+50°C
Operating humidity| 10%-80%

WARRANTY

1. We hereby guarantee the product as follow in accordance with the regulation of consumer damage compensation.
2. In case of failure of the product, please inform the distributor where you purchased the product.
3. Product Warranty will be effective for one year from date of purchase.

Regarding Product Warranty Regulation…

1. We will repair the product at free of charge in case it was failed under the normal operating condition in accordance with the user guide during the warranty period.
2. Although it is within the warranty period, we will charge the repair service fee etc. (repair + product + trawl expense) if it falls under the following cases.

Voiding warranty

1. Defects occurred from the user’s careless handling
2. Defects occurred from the usage with incorrect power voltage (Eg,220V was used to the 110V product)
3. Defects occurred from the improper repair done by the person other than our service engineer.
4. Defects occurred from Force Majeure (fire, salt floodetc).
5. Failure or damage due to the drop, etc (user’s mis-handling) during the operation after installed.
6. Defect occurred from the interior modification at user’s discretion.
7. In case the life cycle of the part expired.

Support

Mail, email or fax the warranty foam to:
YOUR LOCAL DEALER FIRST where you bought this appliance
If your dealer is unable to assist you
94,249beon-GiI, Robotland-Ro, Seo-Gu, Incheon-City, 22756, Korea
www.Isdaewon.co.kr

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>