LEZYNE 73568 Super Pro GPS Bike Computer User Guide

: June 13, 2024
: Lezyne

Table of Contents

LEZYNE 73568 Super Pro GPS Bike Computer
HOW TO CHANGE BATTERY
SPECIFICATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LEZYNE 73568 Super Pro GPS Bike Computer

LEZYNE-73568-Super-Pro-GPS-Bike-Computer-product PRODUCT INFORMATION

MODEL NO.: 73566-A1

MOUNT YOUR PRO CADENCE & SPEED SENSOR

NOTE : Remove the plastic battery cover before use. No magnets are required.

Pro Speed Sensor

Align the rubber shim with the bottom of the sensor.
Securely attach the Pro Speed Sensor to your hub using one of the supplied 0-rings The 0-ring must fit tightly around the hub so the sensor does not move.

Pro Cadence Sensor

Align the rubber shim with the bottom of the sensor.
Securely attach the Pro Cadence Sensor to the inside of your crankarm using one of the supplied □-rings. The 0-ring must fit tightly around the crankarm so the sensor does not move.

GETTING STARTED

Both sensors feature a dual-channel Bluetooth output. This allows for a simultaneous connection to two devices, which is ideal for pairing with both a head unit and an indoor smart trainer at the same time. The Pro Cadence Sensor and Pro Speed Sensor can be paired with Lezyne GPS devices and most fitness apps, and they are compatible with Bluetooth-enabled smartphones. To get started with the Pro Cadence and Pro Speed Sensor, follow the pairing settings of the device if you want to connect the Lezyne sensors with. The wheel and/or crankarm that the Lezyne sensors are attached to may need to be rotated a few times to wake the sensors up. For additional pairing information, please reference the user manual of the device you are attempting to connect the Lezyne sensors.

INPUT WHEEL CIRCUMFERENCE
Pro Speed Sensor only: For the most accurate speed data, your wheel circumference must be programmed into the connected device. Refer to the user manual of the device the Pro Speed Sensor is paired with for instructions on how to input the wheel circumference.

HOW TO CHANGE BATTERY

Use a coin to open battery cover) by turning counterclockwise.
Replace battery CR2032 0 and make sure the sealing o-ringQ is in the groove to ensure water resistance.
Press the cover back and turn the cover clockwise to CLOSE.

PAIR THE SENSOR WITH A LEZYNE GPS

Lezyne GPS

Main Menu
Sensors
- Speed ..,
- Scan BTLE or
- Cadence ..,
- Scan BTLE

SPECIFICATION

Pro Speed Sensor

Pro Cadence Sensor

Size : W32.8xH36.5x014mm
Weight: 17g (with battery)
Water Resistance: 1 m / 3ft
Battery Life (approx): 250 hours
System Compatibility: Bluetooth
FCC ID: 2AD4S-PROSV104
IC ID: 20084-PROSV1 04

Wheel Size and Circumference
The wheel size can be found on the side of the tire. This is not an exact list but a general guide. More specific wheel calculators can be found online. Or you can manual measure http://www.Bikecalc.Com/wheel_size_math

Wheel	Tire	CM

700c/29er

| 20mm| 208
23mm| 209.9
25mm| 211.1
28mm| 213

650c

| 20mm| 192
23mm| 193.8
25mm| 195.1
28mm| 197

20 inch Recumbent

| 20mm| 154.3
23mm| 156.1
25mm| 157.4
28mm| 159.3
32m| 161.8
35m| 163.7
1.00 inch| 157.6
1.25 inch| 161.6
1.50 inch| 165.6
1.75inch| 169.6
1.90 inch| 172
1.95 inch| 172.8
2.00 inch| 17 3.6

650b/27.5

| 20mm| 196
23mm| 197.9
25mm| 199.2
28mm| 201.1
32mm| 203.6
35mm| 205.5
38mm| 207.3
44mm| 211.1
50mm| 214.9
56mm| 218.7
1.00 inch| 199.4

650b/27.5

| 1.25 inch| 203.4
---|---|---
1.50 inch| 207.4
1.75 inch| 211.4
1.90 inch| 213.8
1.95 inch| 214.6
2.00 inch| 215.4
2.10inch| 217
2.125 inch| 217.4
2.20 inch| 218.6
2.25 inch| 219.4
2.30 inch| 220.2
2.35 inch| 221
2.40 inch| 221.6

26 inch mtb

PRO SPEED SENSOR
PRO CADENCE SENSOR

NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Labeling Requirement Notice:
My Changes or modifications not expressly approved by the grantee of this device could void the users authority to operate the equipment This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard{s). Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference recieved, including interference that may cause undesired operation of the device.

Canada, Industry Canada (IC) Notices:
This device complies with Canada license-exempt RSS standard{s). Operation is subject to the following two conditions:

this device may not cause interference and
this device must accept any interference, including interference that may cause undesired operation of the device.

Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized . This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (antennas are greater than 20cm from a person’s body).

Informations concernant ! Exposition aux frequences radio (RF)

SIMPLIFIED EU DECLARATION OF CONFORMITY
The simplified EU declaration of conformity referred to in Article t 0(9) shall be provided as follows: Hereby, Lezyne declares that the radio equipment of type, Information Technology Equipment, is in compliance with Directive 2014/53/EU.

FCC RF EXPOSURE MPE WARNING
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Do not operate or store the GPS unit below -20° Celsius (-4° Fahrenheit) or above 60° Celsius (140° Fahrenheit). Storing the GPS unit in the direct sunlight or inside a parked vehicle can violate the temperature maximums. Battery life and battery health may be adversely affected at temperature extremes.

WARNING: KEEP OUT OF REACH OF CHILDREN

BUTTON CELL BATTERIES ARE HAZARDOUS. NEW AND USED BATTERIES SHOULD BE KEPT AWAY FROM CHILDREN.
LITHIUM COIN BATTERIES CAN CAUSE SEVERE OR FATAL INJURIES IN 2 HOURS OR LESS, IF IT IS SWALLOWED OR PLACED INSIDE ANY PART OF THE BODY.
SEEK MEDICAL ATTENTION IMMEDIATELY IF IT IS SUSPECTED THE BATTERY HAS BEEN SWALLOWED OR PLACED INSIDE ANY PART OF THE BODY.

Lezyne USA, 645 Tank Farm Rd., Unit F, San Luis Dbispo, California 93401

73568-Y13-CADENCE & SPEED SENSOR-QUICK START-Rl-B1

Designed in California