BEDRUG CJ-7 Interior Flooring Kit Installation Guide

BEDRUG CJ-7 Interior Flooring Kit

Product Information

The CJ-7/YJ Jeep Wrangler CJ-7/YJ BedRug is a high-quality interior flooring kit designed specifically for Jeeps. The BedRug material is mold and mildew- resistant, making it durable and easy to maintain. It can be cleaned with water and household cleaning chemicals and is highly resistant to most chemicals. This kit provides a comfortable and stylish flooring solution for your Jeep.

Product Usage Instructions

1. Before starting the installation, read all the instructions provided.
2. If your Jeep has an existing console and old flooring material, remove them.
3. Thoroughly wash and dry the floor pan areas to ensure a clean surface for installation.
4. To install the middle floor piece:
   • Adjust the front seats to the fully forward and tilted opposition.
   • Place the rear floor piece into position.
   • Cut slits for seat belts to pass through the underside of the floor.
   • If your Jeep has factory plastic covers, cut holes to accommodate them.
   • Do not bolt seat belt brackets on top of the BedRug material.
   • Clean the surface with alcohol and remove the film backing from both pieces.
   • Roll the floor back into place, ensuring adhesive attachment by firmly pressing the top surface.
   • Repeat these steps as necessary until all pieces are attached.
5. To install the front floor pieces:
   • Adjust the front seats to the rear-most position for maximum clearance.
   • Place the front floor pieces into position.
   • Pull back apart to access the hook fastener.
   • Clean the surface with alcohol and remove the film backing.
   • Roll the part back into place, ensuring adhesive attachment by firmly pressing the top surface.
   • Repeat these steps for the other front floor piece.
6. To install the trans hump piece:
   • Remove rubber shifter boots and cut slits to fit the piece over floor shifters.
   • Clean the surface with alcohol and remove the film backing.
   • Start on one side and fit the trans hump piece into place, ensuring it fits against the floor piece without a gap.
   • Repeat these steps for the other side.
7. To install the front floor pieces:
   • Clean the side panel surfaces with alcohol and remove the film backing.
   • Install the pieces as shown in the provided drawings.
   • Repeat these steps for the opposite side.
   • Trim rocker panel pieces at proper score lines. Refer to the drawing on Page 5 for guidance.

For any further assistance or inquiries, you can contact BedRug, Inc. at:

• Address: 635 Old Hickory Blvd, Old Hickory, TN 37138-3162
• Phone: 800-462-8435
• Website: www.bedrug.com

Congratulations on choosing the finest interior flooring kit available for your Jeep. The BedRug material is mold and mildew-resistant, easily cleaned with water & household cleaning chemicals, and extremely resistant to most chemicals.

• Kit Contents: Driver side front floor, passenger side front floor, rear passenger floor, trans hump piece, side panel right and left, A-pillar right and left, heatshield material, hardware kit, and instruction sheet.
• Tools needed: Phillips screwdriver, utility knife, soap, water, and rubbing alcohol.

Installation Instructions

PREPARATION

1. Read all instructions before beginning installation.

2. Remove the console and old Jeep flooring material (if equipped).

3. Wash and dry the floor pan areas thoroughly.

4. Cut the hook with the tape backing, provided in the hardware kit, to the lengths indicated on the drawing (page 5).
   Place the loop onto each location. Do not remove the tape backing at this time.
   ( NOTE: Cut the longest pieces first.)

5. Pre-install provided heat shields on the underside of the three front pieces in the areas shown below, using the locator marks. (Fig. 1 thru 3) NOTE: See drawing (Page 5) for trans hump shield placement. INSTALLING MIDDLE FLOOR PIECE

6. Adjust the front seats to the fully forward and tilted up (passenger entry) position. Next place the rear floor piece into place. (Fig. 4 and Fig. 5)

7. Cut slits for seat belts to pass thru the underside of the floor as shown. If equipped with factory plastic covers, cut holes to accommodate. (Fig. 6 and Fig. 7) NOTE: Do not bolt seat belt brackets on top of BedRug material, to ensure bolt torque is accurate.

8. Next, pull back the floor piece to access the hook fastener. (Fig. 8) Clean the surface with alcohol then remove the film backing from both pieces and roll the floor back into place. Firmly press the top surface to ensure adhesive attachment, and repeat as necessary until all pieces are attached. INSTALLING FRONT FLOOR PIECES

9. Adjust the front seats to the rearmost position to allow maximum clearance for installation. Place front floor pieces into place. (Fig. 10)

10. Once properly aligned, pull the back part to access the hook fastener (Fig. 11). Clean the surface with alcohol then remove the film backing and roll the part back into place. Firmly press the top surface to ensure adhesive attachment. Repeat for other front floor pieces.

11. Once properly aligned, pull the back part to access the hook fastener (Fig. 11). Clean the surface with alcohol then remove the film backing and roll the part back into place. Firmly press the top surface to ensure adhesive attachment. Repeat for another front floor piece.

12. Clean the side panel surfaces with alcohol, then remove the film backing and install the pieces as shown. (Fig. 14 -17) Repeat for the opposite side. Rocker panel pieces should be trimmed at proper score lines. See drawing Page 5.

COMPLETED INSTALLATION

воттом VIEW (FOAM SIDE)
BRCYJ76F HOOK INSTALLATION

WARNING

The use of front floor mats is not recommended with BedRug or BedTred floor kits. If floor mats are used, it is imperative to re-use the removable retention hooks from the factory carpet, installed to the manufacturer’s specifications. Do not use floor mats or liners with BedTred Kits. Do not use floor mats or liners with BedRug Kits without retention hooks.

• Please retain these instructions for future reference in your vehicle’s glove box

BEDRUG®BEDTRED™ CLEANING INFORMATION
The mildew-resistant BedRug/BedTred foam will not absorb liquids. The engineered composite surface resists stains and deterioration from most acids, chemicals, gas oils, etc. Therefore, by following the cleaning instructions below, your BedRug/BedTred will remain serviceable for as long as you own your vehicle.

Cleaning your BedRug is easy:

1. A vacuum, broom, brush or compressed air can be used to remove dirt, grime, sand, mulch, etc. Because water will not harm the product, pressure washing is also an effective way to clean a soiled BedRug/BedTred.
2. Although most acids will not harm the BedRug/BedTred, baking soda should be applied immediately to neutralize the acid to ensure the safety of the paint on the vehicle.
3. To clean tougher jobs such as gasoline, oil, chemicals, acid spills or leaks from your BedRug/BedTred use detergent soap with degreaser and water, then rinse thoroughly. This detergent soap is used in most car wash locations with pressure washing equipment. The polypropylene closed-cell foam will not absorb water and the composite surface dries in minutes.

If you have additional questions, call BedRug Inc. customer service at 800-462-8435.

WARRANTY

LIMITED WARRANTY

BedRug Inc. warrants BedRug and BedTred products for Jeep vehicles for three years from the original date of purchase. The warranty is limited to the original purchaser and is not transferable. The product is warranted to be free from defects in materials and workmanship. The warranty is void if the product has been damaged by accident, unreasonable use, neglect, improper service/installation/removal, modifications, acts of God, normal wear and tear, or other causes not arising out of defective materials or workmanship. Consequential and incidental damages are not covered under this warranty. The warranty does not cover labor, the cost of shipping, or cost of returning the product for warranty service inspection. The terms of this warranty may vary from state to state. You may have rights under specific state laws that differ from the terms of this warranty. Proof of purchase will be required for warranty service. The product should be cleaned before return. A return authorization number must be obtained prior to returning any product. For warranty instructions, returns, and packaging contact BedRug Inc. Customer Service at 800-462-8435.

PRODUCT REGISTRATION
Thank you for purchasing your BedRug product! We would appreciate it if you would take a few minutes to register your purchase. Registration allows us to provide, with your permission, important updates, service information, helpful hints or warranty service should you ever require technical support. BedRug offers the option of returning product registration forms electronically, rather than having to fill them out by hand. You can be assured that BedRug does not share or sell the information you provide. Save a copy of your sales receipt. Activate your warranty by registering your product online at http://www.bedrug.com/customer-service/product-registration.html or by scanning the QR code. You will need the 6- digit lot and date code found on the underside of the tailgate, see label example below.

• TGCO7
• DESC 07+ GMT900 TAILGATE
• WO#511247 LOT # 123456]
• DATE: 04/13/12|TR# S1E123
• MADE IN USA

References

• BedRug Bed Mats Bed Liners & Accessories | RealTruck
• BedRug Bed Mats Bed Liners & Accessories | RealTruck

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>