SINED CAMINETTO-PANAREA Electric Fireplace User Manual

: June 4, 2024
: SINED

Table of Contents

SINED CAMINETTO-PANAREA Electric Fireplace
Unpacking Operation
Shape and Size (mm)
Installation Instructions
Manual Key Operation
Troubleshooting
Documents / Resources

SINED CAMINETTO-PANAREA Electric Fireplace

WARNING

In avoid to overheating, do not cover the fireplace.
Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool..
Do not use this heater if it has been dropped.
Do not use if there are visible signs of damage to the heater. The heater must not be used if the glass panels are damaged.
Use this heater on a horizontal and stable surface, or fix it to the wall, as applicable.
Do not use this heater in small rooms when they are occupied by persons not capable leaving the room on their own, unless constant supervision is provided.
Extreme caution is necessary when children are near the fireplace and whenever the fireplace is left operating and unattended.
Always unplug fireplace when not in use.
Do not operate the fireplace with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner, return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
Do not use outdoors. It’s only suitable for indoor use.
Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tipped over.
To disconnect fireplace, turn controls to off, then remove plug from outlet.
Do not inset or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the fireplace.
To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
It has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, or flammable liquids are used or stored.
Use this fireplace only as describes in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
DANGER-HIGH Temperatures may be generated under certain abnormal conditions. Do not partially or fully cover or obstruct the front of the heater.
Do not use this heater with a programmer, timer, independent remote control system, or any other device that automatically turns on the heater, because if the heater is covered or incorrectly positioned, there is a risk of fire.
Do not use the Electric fireplace for any other purposes than those described in this instruction manual.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Do not use this appliance outdoors.
Always unplug the Electric fireplace from the power supply when not in use and before cleaning.
To protect against the risk of electric shock, do not immerse the appliance in water or in any other liquids.
Components should only be serviced by an approved electro technician.
“If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.”

Cleaning the exterior of the appliance

CAUTION : In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

Unpacking Operation

The product Must be handled carefully to avoid damaging the glass

Shape and Size (mm)

Installation Instructions

Hole size (Find hole size symbol on product dimensions.)
Note : Support platform need to be flat, complete and firm. Power socket should be connected with ground wire.

NOTE : The exact furniture or mantel opening dimensions are :width 715 x height 615(mm). When designing the opening ,it is recommended to add a tolerance of +3mm to the width and height.
CAUTION : For proper ventilation ,leave 30mm minimum air space clearance between the back of the firebox and any other materials.

Insert the firebox from the back
Mount the securing plates on both sides of the firebox
Fix the plates using the including screws

Functional area on the front:

Safety tips : To prevent fire, there shall not be anything around 100 cm of the air outlet

Configuration Information

Basic

| Infrared remote control
Manual key
Adjustable flame
Heating function
Single-color flame

Optional / not included

| Multi-color flame
Crystal
Cobblestone
DIY fake log
Safety Certification| CE RoHS

Attachments

| Remote control
Manual
Warranty card

This product has been tested in special electrical room according to national standards. If you need help during use, please contact us in time.

Manual Key Operation

Remote Control Function
Digital Screen
Remote Operation

On/Off
Press this button to turn on with F1 on screen. Press this button to turn off with nothing on screen.
This button no function
Adjust flame brightness
Default F1. F1-F2-F3-F4-F5-F6-F1. The number corresponds to flame brightness.

Display	F1	F2	F3	F4	F5	F6
Set	1	2	3	4	5	6
Brightness	100%	80%	60%	40%	20%	0%

Heater (Be off by default)

LL” 1-level heater with one icon ****
”HH” 2-level heater with two icons

Temperature rises
The default startup temperature is 19℃. Short press to rise one degree. Temperature cycle: 19-30℃(66-68℉). Long press for 5 seconds to convert temperature units. C(F) can be turned off for heating.

Temperature reduces
Short press to reduce 1 degree. Rising to a certain temperature, it will turn off the heating when it rises by 1 degree. Reducing to a certain temperature, it will turn on the heating when it reduces by 2 degrees.

Timer
It’s disabled by default. Short pressing will adjust the timer range from 30Min-1H-2H-3H-4H-5H-6H-7H-8H-30Min. The symbol light is on by default.

This button no function

Day timer
There is a timing function. When turning on the fireplace, the timer icon light will be on. The clock will show 00:00. The week icon light will be on and show SUN.
When the timer is needed after turning on, press “DAY” button on remote control. Each time you press the button, the week icon light will be on from left to right to set the time to the current date.

Hour timer
Each time you press the “HOUR” button, the time is increased by one hour. Set the time to the current hour, hour timer scope is: 00-23.

Minutes timer
Each time you press the “MIN” button, the time is increased by one minute. Set the time to the current minutes, minutes timer scope is: 00-59. When it is not unplugged or disconnected, the on-off time will have memory function, which will not be reset. If unusual timer id discovered, the batteries powering the mainboard may be dead. Please replace the batteries quickly. (Battery Model: CR1220-3V), (Each time you press the button, the buzzer will make a short sound.)

Week timer
It has a week timing switch function.

First press “WEEK TIME” button, the week icon will turn the current time to SUN(Sunday) and flash. The icon of clock and ON will flash at the same time.
Set the startup time of the day. Press “HOUR” button to set starting up hour, press “MIN” button to set starting up minutes. (Each time you press the button, the number will increase 1.) Then press “SET UP” button to confirm. ON light will be off and OFF light will be on.
Set the off time of the day, the process is the same with setting the startup time. After setting for one day, press “WEEK TIME” again to set for another day.
If you don’t operate the week timer during the week display flashes for ten seconds, the clock on the digital screen will be always on. The light of ON/OFF will be off. (Each time you short press the button, the buzzer will make a short sound.)

On/Off week timer
Press the button to turn on/off the week timer function.

Alarm

Electric fireplace has window opening detection function. When it is in heating state and detects a temperature drop of 3 degrees within 5 minutes, it will turn of heating function automatically. Buzzer will make a long sound three times. The alarm icon light will flash to remind the user that the window has been opened.
After the alarm is on, press the heater or temperature button to clear alarm reminder.

This button has no function

Troubleshooting

Symptom| Probable Causes| Solution

Not Work

| Poor contact between plug and socket|

Connect the plug correctly or change it

Power is off| Turn on

Protector overheats

| Turn off power, natural cooling for 15min.
Protector overheats and burned out|

After-sale repairing

Heating without flames|

Lights damage

|

After-sale repairing

Flames without heating|

Heater is off

|

Turn on heater

Remote control not responding| Misaligned infrared reception| Adjust angles and distance
An internal fuse has blown| After-sale repairing
Flames with noise|

Spark shaft is falling

|

Contact the after-sales service.

Part of the flame is not

bright

|

The lamp strip socket is loose or falls off

|

After-sale repairing

Caution
Please cut off the power before the maintenance of the appliance. Workers with maintenance qualification are required to avoid accidents and personal injury.

Final Interpretation
The final interpretation right is of our company. Please know if the product appearance and structure are changed, there is no need to inform the user.

Correct Disposal of this product
This marking indicates that this product should not be disposed with other household wastes throughout the EU.To prevent possible harm to the environment or human health from uncontrolled waste disposal,recycle it responsibly to promote the sustainable reuse of material resources.To return your used device,please use the return and collection systems or contact the retailer where the product was purchased.They can take this product for environmental safe,recycling.

Production: Suzhou Yueyu Thermal Energy Technology Co.
Indirizzo della fabbrica: No. 6 Xinghai Road, Liuhe, Taicang, Taicang City, City Suzhou, Jiangsu, Cina
Made in China Imported in Italy by M.P.C. srl Via Tortona 20144 Milano Italia Tel +39 02 21117815 e-mail info@mpcshop.it sito web www.sinedtechnology.com
Trademark SINED and logo SINED are registered by Sined Ventas Online S.L.U. EUTM 018196373

Documents / Resources

| SINED CAMINETTO-PANAREA Electric Fireplace [pdf] User Manual
CAMINETTO-PANAREA, Electric Fireplace, Fireplace, CAMINETTO-PANAREA Electric Fireplace
---|---