Tucanourbano R228X Tablier Scooter Instruction Manual

Tucanourbano R228X Tablier Scooter

Product Information

The leg cover is a scooter accessory designed to provide protection from wind and cold weather. It is compatible with specific scooter models. For compatibility information, please consult your dealer or visit the website www.tucanourbano.it.

Product Usage Instructions

• To ensure efficient and safe usage of the leg cover, please follow the assembly instructions carefully. If you have any doubts, consult qualified personnel.
• After assembling the product, verify that it is correctly attached and does not obstruct driving, steering, foot placement, or the functioning of the scooter. Check that all straps are securely fixed and will not catch in any moving part. Failure to follow these instructions may compromise the performance of the product and your safety.
• Before using the product for the first time in traffic, practice quickly placing your feet on the ground and ensure you can safely execute all maneuvers. Start practicing in a safe and traffic-free area, first while stationary on the center stand, and then at low speeds. Failure to follow these instructions may put your safety at risk.
• After each use of your scooter, and especially after any fall, accident, or impact (e.g., riding off a high pavement), carefully check the position of the leg cover. Ensure that all straps are correctly tensioned, screws and bolts are tight, and all attachments are intact. If any issues are found, remove the product before continuing. Additionally, periodically inspect the tightness of the screws/nuts and the tension of the straps.
• During scooter usage, position your feet in a way that allows for quick contact with the ground during stops, particularly when using the side straps 5 tucked between the seat and driver.
• Do not make any modifications to the product and use only original components. Also, be cautious of strong winds. Remember to keep the SGAS anti-flap air chambers properly inflated. Keep these instructions for future reference.

WARNING

• Before assembling the product, check that Termoscud® is compatible with your model of scooter. Consult your dealer on the website www.tucanourbano.it.
• Ensure correct and safe usage of the leg cover by following the assembly instructions carefully: in case of doubt, consult qualified personnel.
• Once you have assembled the product, check that it is correctly attached and that no part of the product impedes driving, steering, correct functioning of the vehicle, or your ability t place your feet on the ground. Make sure all straps are securely fixed with no risk of catching in any moving part. Failure to follow these instructions will impair the product’s performance and put your safety at risk.
• Before using the product for the first time, practice putting your feet to the ground quickly and check that all other maneuvers can be safely executed. Do this in a safe place where there is no traffic, first on the center stand with the vehicle still and then whilst driving at low speed. Failure to follow these instructions will put your safety at risk.
• Every time you use your scooter and after any fall, accident or impact (eg. riding off a high pavement), check carefully that the product is correctly positioned, that the straps are correctly tensioned, that all screws and bolts are tight and that all attachments are intact. not, remove the product before proceeding.
• When using your scooter, position your feet so they can rapidly contact the ground during stops, especially when ‘side straps 5’ are tucked between seat and driver.
• Do not change or modify the product in any way. Only use original parts.
• The leg cover may alter the aerodynamics of your vehicle. This must be taken into consideration. keep the vehicle and its speed under control, especially in strong winds.
• Remember to keep the anti-flap SGAS air chambers fully inflated.
• Keep these instructions for future reference.

INSTALLATION

• Start: Summary view of the assembly steps (A>F) and finished product fitted on the scooter.
• Step A: Unfold Termoscud® on the scooter’s seat with straps 1 and 3 forward.
• Step B: Fasten Termoscud® on both sides, using the screws (A) included in the assembly kit, threading them through the holes at points 1. Fasten Termoscud® on both sides, using the scooter’s original fasteners* or screws, threading them through the holes at points 1bis.
• Step C: Fasten the hooks of the straps 3 to the edge of the bodywork. Close the buckles of straps 3bis under the leg cover. Behind the bodywork.
• Step D: Fasten the hooks of the straps 6 to the edge of the bodywork, turning them inwards.
• Step E: Fasten the hooks of the straps 6bis to the edge of the bodywork, behind the front wheel.
• Step F: Fasten the hooks of the straps 2 to the edge of the bodywork under the footboard.

Note

• Adjust the position of Termoscud® using the regulations of the straps to fit perfectly on the shield.
• Finally inflate S.G.A.S. tubes.
• Exceeding portions of the straps must be tucked under the Termoscud® cover to avoid flapping.

S.G.A.S. (patented anti-flap inflatable system) with new valve fitted with incorporated cap and watertight closure.
S.G.A.S. adapter included for manual/ pump inflation: makes pumping hygienic and prevents air leakage when the valve is being closed.

DETAILS

1. Chest cover with safety strap.
2. During summer months, deflate the S.G.A.S. air chambers and roll them back towards the inside; then fasten them by passing the red cords through the loops provided on the exterior of the Termoscud®.
3. Get a better protection by sitting on straps 5, especially in cold conditions.
4. As a deterrent write your registration number in the space provided.
5. An elasticized waterproof cover can be pulled over the seat when the scooter is parked.
6. Inside the Termoscud® packaging are some clear adhesive stickers to be applied to the bodywork in order to protect the paintwork. These are removable and will not leave residues of glue. If the Termoscud® is not fitted correctly or the straps kept taught, marks could appear on the bodywork after a period of time.
7. To wash Termoscud® at the end of the season use a damp cloth and let dry well before storing.
   DO NOT WASH WITH THE PRESSURE WASHER JET.

NOTE Photos and drawings are purely indicative. Tucano Urbano reserves the right to modify or improve the product at any time, without prior notification and with no obligation to apply such modifications to products already sold.

References

• Abbigliamento e Accessori Moto, Bici, Scooter | Tucano Urbano

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>