USCutter GS-207M Heat Press Instruction Manual

June 13, 2024
USCutter

USCutter logo USCutter GS-207M Heat PressOperation Manual
(GS-207M)

Safety Instructions

When using your heat press, basic precautions should always be followed, including the following:

  1. Read all instructions.
  2. Use heat press only for its intended use.
  3. To reduce the risk of electric shock, do not immerse the heat press in water or other liquids.
  4. Never pull cord to disconnect from outlet, instead grasp plug and pull to disconnect.
  5.  Do not allow cord to touch hot surfaces, allow heat press to cool completely before storing.
  6. Do not operate heat press with a damaged cord or if the equipment has been dropped or damaged.To reduce the risk of electric shock, do not disassemble or attempt to repair the heat press. Take it to a qualified service person for examination and repair. Incorrect assembly or repair could increase the risk of fire, electric shock, or injury to persons when the equipment is used.
  7. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  8. Close supervision is necessary for any heat press being used by or near children. Do not leave equipment unattended while connected.
  9. Burns can occur when touching hot metal parts.
  10. To reduce the likelihood of circuit overload, do not operate other high voltage equipment on the same circuit.
  11. If an extension cord is necessary, then a 20 amperage rated cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over.

Technical Parameters

USCutter GS-207M Heat Press - Technical Parameters

Model: GS-207M
Heater Size: W195mm*H170mm

for 400ml/500ml/600ml aluminum sports water bottle.
Power(120volt)| 4300W/4120W
16.1 Amps(max)
Power(240volt)| 4300W/4120W
8.1Amps(max)
Temperature Range:| Max.220℃/430℉
Time Range:| 0~999S
Machine Size:| 65.2×33.9×28.5cm
Packing Size:| 73×43×40cm
Packing Weight:| 24kg
Maximum Paper
Printing Size:| 400ml sports bottle: 17599mm(LW)
500ml sports bottle: 175114mm(LW)
600ml sports bottle: 175134mm(LW)
Suggest  Temp&Time Setting:| 150C/190C 40-50secs
302F/374F 40-50secs
Certificate:| CE,FCC
Warranty:| One year for whole machine except heaters

Machine View

USCutter GS-207M Heat Press - Machine View

Control Panel Guide

USCutter GS-207M Heat Press - Control Panel

Operation Instructions

1.Connecting the System

  • CONNECT THE POWER CORD
    Connect the power cord into a properly grounded electrical outlet with a sufficient amperage rating.

  • VOLTAGE
    120 Volt – GS-207M requires a full 20 amp grounded circuit for 120 volt operation.
    240 Volt – GS-207M requires a full 10 amp grounded circuit for 240 volt operation.

  • EXTENSION CORDS If used, should be as short as possible and not less than 12 gauge.Heavy duty cords are recommended.

  • CIRCUITS that have less than 15 amps or that have other high demand equipment or appliances(especially more than one heat seal machine) plugged in, should not be used.

NOTE: If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person in order to avoid hazard.

2.Turn On the System
Switch on the system. (fig.2.1)

USCutter GS-207M Heat Press - figure 1

3.Adjusting the Temperature
3.1 Press the Mode Select button located in the center of the Control Panel (fig.3.1).Press (+) and (-) button to select different heater. (fig.3.2).USCutter GS-207M Heat Press - figure 23.2 For heater 1/2 and 3/4, press “set” button to choose “start temp” or “finish temp”, press (+) and (-)button to set temperature. For heater 5 and 6,press “set” button to choose “start temp”, press (+) and (-)button to set temperature.The temperature can be set from 0° C (0° F) to 220° C (428° F). (fig.3.2)USCutter GS-207M Heat Press - figure 33.3 press set button again to finish setting,move the cursor to “next”, ready to enter time setting page. (fig.3.3)USCutter GS-207M Heat Press - figure
4

Remark:

  1. heater 1/2 represent no.1 and no.2 heater, can only be set temperature at once time together, because left air cylinder close the heater 1/2 together. Heater 1/2 can set “start temp” and “finish temp”.
  2. heater 3/4 represent no.3 and no.4 heater, can only be set temperature at once time together, because right air cylinder close the heater 3/4 together. Heater 3/4 can set “start temp” and “finish temp”.
  3. Heater 5 does not work for GS-207M.
  4. Heater 6 does not work for GS-207M

4.Adjusting Time
4.1 In the time setting page, Press (+) and (-) button to select different heater..(fig.4.1)USCutter GS-207M Heat Press - figure
54.2 Press “set” button to activate time value setting. Press (-) button to lower the value ,or press the (+) button to raise the time value .The time setting range can be set from 0~999. Move the cursor to “back”,press “set’ button to get back to the main interface. (fig.4.2)USCutter GS-207M Heat Press - figure 6 5.Printing And Pressing
5.1 Once heater reaches start temperature,put bottles inside of mug heaterUSCutter GS-207M Heat Press - figure 75.2 Adjust suitable pressure by turning pressure knob.USCutter GS-207M Heat Press -
figure 8

5.3 Then close handle to start transfer printing process.USCutter GS-207M
Heat Press - figure 95.3 Once printing process is over, buzzer will alarm and open the handle then take out bottles out of machine.USCutter GS-207M Heat Press - figure 10

Remark:

  1. Station 1/2 must work with two mugs inside together, working only with 1 mug inside will damage the machine.
  2. Station 3/4 must work with two mugs inside together, working only with 1 mug inside will damage the machine.
  3. Each heater’s temperature is separately controlled by different triac, can be calibrated separately. But we do not suggest customer make calibration unless there is a need.

6.How to Change Heater
Plug off the 4 phase plugUSCutter GS-207M Heat Press - figure
11Take off the heater. Then do the opposite operation can change a new heater onto the machineUSCutter GS-207M Heat Press - figure
12 7.Sub Menu Introduction
In the time setting page, there is sub menu button, move the cursor to the button, press “set” button to enter into sub menu
7.1 Language setting.we offer 4
language for customer needs.
English/Spanish/Russia/Portuguese(fig.7.1). Once finish setting,go to next page.USCutter GS-207M Heat Press - figure 13

7.2 Temperature calibration setting.
Customer can make calibration on each heater once the heater’s temperature is not correct.(fig.7.2).Once finish setting,go to next page.USCutter GS-207M
Heat Press - figure 147.3 Fahrenheit and Celsius setting. (fig.7.3).Once finish setting,go to next page.USCutter GS-207M Heat Press -
figure 157.4 Auto-sleep setting. Customer can set auto-sleep time. Once time is reached,machine will auto close without any operation (fig.7.4).Once finish setting,go to next page.USCutter GS-207M Heat Press -
figure 167.5 Brightness setting.Customer can reduce or increase brightness of the screen. (fig.7.5).Once finish setting,go to next page.USCutter GS-207M Heat Press - figure 177.6 Counter Collection.Here customer can see how many mugs have been printer by each heater. This setting can not be changed.. (fig.7.6).Once finish setting,go back to the main interface.
USCutter GS-207M Heat Press - figure 18

Exploded Views

USCutter GS-207M Heat Press - Exploded Views GS- 207M contains 4 main parts:

  1. Machine base assemble
  2. Control box assemble
  3. Heating elements assemble
  4. Pressure system assemble

1. Machine Base Assemble:USCutter GS-207M Heat Press - Machine Base
Assemble Parts list:

No.

| P/N| Name|

Qty

---|---|---|---
1| J.03.05.0600| Machine Base| 1
2| J.03.06.0104| Round head bolt M3x6| 2
3| J.03.04.0011| Switch Power Supply DC12V| 1
4| J.03.04.0077| socket| 1
5| J.03.06.0077| Countersunk screw M3x8| 2
6| J.03.04.0079| On/off switch| 1
7| J.02.04.0138| Circuit breaker 18A| 1
J.02.04.0139| Circuit breaker 10A| 1
8| J.03.04.0078| Terminal Block| 1
9| J.03.06.0117| Ball headed bolt M4*10| 2
10| J.03.03.0037| Rubber foot| 4

2. Control Box AssembleUSCutter GS-207M Heat Press - . Control Box
Assemble Parts List

No.

| P/N| Name|

Qty

---|---|---|---
1| J.03.05.0602| Top Cover| 1
2| J.02.04.0164| 4 phase aviation plug(Male) with wires welded| 4
3| J.03.06.0165| Ball headed bolt M5-12| 6
4| J.03.04.0166| Circuit board GSK-07| 1
5| J.03.06.0117| Ball headed bolt M4*10| 4
6| J.03.01.0025| Sticker| 1
7| J.03.05.0403| Circuit board cover| 1
8| J.03.06.0104| Round head bolt M3x6| 4

3. Heating elements assembleUSCutter GS-207M Heat Press - Heating
Element Assemble 3.1.Heater Cover Assemble:USCutter GS-207M Heat Press - Heater Cover
Assemble Parts List:

No.

| P/N| Name|

Qty

---|---|---|---
1| J.03.06.0102| Round head bolt M6x16| 4
2| J.03.04.0184| Buzzer| 4
3| J.03.05.0601| Heater cover| 1
4| J.03.06.0032| Handle Screw| 8
5| J.03.05.0456| Supporting pillar| 2
6| J.03.05.0417| Heater fix board| 4
7| J.03.05.0421| Bottom base| 4
8| J.03.05.0414| Door type cover-1| 4
9| J.03.05.0415| Door type cofer-2| 4

3.2 Heater Shaft AssembleUSCutter GS-207M Heat Press - Heater Shaft
Assemble Parts List

No.

| P/N| Name|

Qty

---|---|---|---
1| J.03.06.0117| Ball headed bolt M410| 6
2| J.03.05.0426| Arc supporting plate| 2
3| J.03.05.0419| Supporting board-1| 1
4| J.03.05.0420| Supporting board-2| 1
5| J.03.05.0418| connector-2| 1
6| J.03.06.0103| Ball headed bolt M5
10| 2
7| J.03.06.0142| Shoulder screw M5-6*12| 1
8| J.03.05.0455| Connecting sheet| 1

4. Pressure System AssembleUSCutter GS-207M Heat Press -
Pressure System Assemble Parts List

No.

| P/N| Name|

Qty

---|---|---|---
1| J.03.06.0005| Clamp| 1
2| J.02.04.0148| Magnet switch| 1
3| J.03.03.0003| Ball Shape Handle| 1
4| J.03.06.0212| Screw M10-70| 1
5| J.03.06.0127| Nut M10| 1
6| J.03.05.0595| Connecting sheet| 1
7| J.03.06.0140| Ball headed bolt M5*8| 1
8| J.03.05.0596| Connecting set| 1
9| J.03.06.0144| Cup head screw M10-20| 1
10| J.03.05.0615| Connecting sheet| 1

Electrical Schematic

USCutter GS-207M Heat Press - Electrical SchematicUSCutter logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals