Borla 11972 Bronco Sport 1.5L Axle Back Exhaust System Installation Guide

Borla 11972 Bronco Sport 1.5L Axle Back Exhaust System

Product Information

• Manufacturer: Borla Performance Industries
• Address: 500 Borla Drive, Johnson City, TN, 37604-7523
• Contact Number: 805-986-8600
• Product Model: Ford Bronco Sport 1.5L
• Part Numbers: 11972, 11972BC

Product Usage Instructions

Before beginning the installation of your Borla Performance exhaust system, please ensure that you have all the necessary parts by comparing the contents of the box with the provided bill of materials.

Minimum Required Tools

• 3/8 drive ratchet
• 3/8 drive extension
• 15mm deep well socket
• Reciprocating Saw with metal cutting blade
• Pry bar

Shop Supplies:
Spray lubricant

Original Exhaust System Removal:

1. Lubricate all hangers, rubber isolators, bolts, and nuts.
2. Using a reciprocating saw, make a cut 2 inches in front of the rear muffler.
3. Remove the rear muffler assembly hangers from the two rubber isolators and remove the rear muffler assembly from the vehicle.
4. Original exhaust system removed.

Borla Performance Axle-Back Exhaust System Installation:

1. Orient components on the shop floor according to the Borla bill of materials drawing on page 2.
2. Place a clamp over the expanded end of the Muffler Assembly and insert the inlet to the vehicle. Insert the hangers into the original rubber isolators. Do not tighten the clamp.
3. Once the position has been determined to be correct, tighten the Accuseal clamps to 32-35 ft. lbs.
4. Before starting your vehicle, make sure to check all wires, hoses, brake lines, body parts, and tires for safe clearance from the exhaust system.
5. Start the vehicle and check for any leaks. If any leaks are found, determine the cause (such as loose or incorrectly positioned clamp) and repair as necessary.
   WARNING: Use extreme caution during installation. Torque all fasteners according to the manufacturer’s torque values and tightening sequence. DO NOT use air impact tools to tighten fasteners on Borla Performance Exhaust Systems. Use of such tools may result in bent flanges or gasket contact areas leading to exhaust leaks.
   NOTE: When you first start your vehicle after the installation of your new Borla Performance Exhaust System, there may be some smoke and fumes coming from the system. This is a protective oil-based coating used in the manufacturing of mandrel bent performance exhaust tubing. This is not a problem and will disappear within a very short period of time after the exhaust has reached normal operating temperatures.

Please compare the parts in the box with the bill of materials provided to assure that you have all the parts necessary for this installation.

• These instructions have been written to help you with the installation of your Borla Performance exhaust system. Please read this document complete-ly before beginning the installation of your system.
• To ensure this part number fits your specific model year, please visit our website for the latest model year listings at www.BORLA.com

INTRODUCTION

Thank you for purchasing a Borla Performance Axle-Back™ exhaust system.

• Borla Performance Axle-Back™ exhaust system PNs 11972 and 11972BC are designed for the Ford Bronco Sport, equipped with a 1.5L inline-3 turbo-charged engine and 4WD automatic transmission.
• Borla Performance Industries recommends that an exhaust shop or professional after market parts installer, who has all the necessary equipment, tools and experi-enced personnel needed for proper installation, should perform the installation of this system. However, if you decide to perform the installation, we recommend someone should help you. Ensure the installer uses all under car safety precautions including eye protection.
• Please take time to read and understand the following…
• By installing your Borla Performance exhaust system, you indicate that you have read this document and you agree with the terms stated below.
• It is the responsibility of the purchaser to follow all installation instruction guidelines and safety procedures supplied with your Borla Performance exhaust system.
• Borla Performance Industries assumes no responsibility for damages occurring from misuse, abuse, improper installation, improper operation, lack of responsible care, or all previously stated reasons resulting from incompatibility with other manufacturer’s products and/or systems.
• Included with your Borla Performance exhaust system is a warranty card. Please read it carefully before you begin any work on your vehicle. If you should have any questions regarding our warranty policy, installation, or any other matter pertaining to your new Borla Performance exhaust system, please give us a call at the number provided on the warranty card.

Minimum Required Tool List

TOOLS:

1. 3/8” drive ratchet
2. 3/8” drive extension 6”
3. 15mm deep well socket
4. Reciprocating Saw with metal cutting blade
5. Pry bar

SHOP SUPPLIES:
Spray lubricant

Borla Performance – Bill of Materials

SAFETY INSTRUCTION

• Caution!!! Never work on a hot exhaust system. Serious injury in the form of burns can result If the vehicle has been in use and the exhaust system is hot, allow vehicle to cool for at least 1 hour. Always wear eye protection when working under any vehicle.

• Note: It is our recommendation that you use a hoist or hydraulic lift to facilitate the installation of your new Borla Performance Exhaust System.
  Taking all under car safety precautions, lift the vehicle using a hoist or hydraulic lift. Once this has been done, you may begin the removal of your old exhaust system from your vehicle.

• Note: Before removing the original exhaust system from your vehicle, please compare the parts you have received with the bill of materials provided on the previous page to assure that you have all the parts neces-sary for the installation of your new Borla Performance Exhaust System.

• Note: With a used vehicle, we suggest a penetrating spray lubricant to be applied liberally to all exhaust fasteners and allowing a significant period of time for the chemical to lubri- cate the threads before attempting to disassemble.

Original Exhaust System Removal

1. Lubricate all hangers, rubber isolators, bolts and nuts.
2. Using a reciprocating saw, make a cut 2” in front of the rear muffler (Figs. 1- 2).

3. Using muffler stand or an additional person, remove the rear muffler as-sembly hangers from the two rubber isolators and remove the rear muffler assembly from the vehicle (Fig. 3).
4. Original exhaust system removed.

Borla Performance Axle-Back Exhaust System Installation

1. Orient components on shop floor according to Borla bill of materials draw-ing on page 2.
2. Place a clamp over the expanded end of the Muffler Assembly and insert the inlet to the vehicle. Insert the hangers into the original rubber isolators (Fig. 7). Do not tighten the clamp.
3. Once position has been determined to be correct, tighten the Accuseal clamps to 32-35 ft. lbs.
4. Before starting your vehicle, make sure to check all wires, hoses, brake lines, body parts and tires for safe clearance from the exhaust system.
5. Start the vehicle and check for any leaks. If any leaks are found, determine cause (such as loose or incorrectly positioned clamp) and repair as neces-sary.

  *  **WARNING:** Use extreme caution during installation. Torque all fasteners according to manufactur-er’s torque values and tightening sequence. DO NOT use air impact tools to tighten fasteners on Borla Performance Exhaust Systems. Use of such tools may result in bent flanges or gasket contact areas leading to exhaust leaks.
  *  **NOTE:** When you first start your vehicle after the installation of your new Borla Performance Exhaust System, there may be some smoke and fumes coming from the system. This is a protective oil based coat-ing used in the manufacturing of mandrel bent performance exhaust tubing. This is not a problem and will disappear within a very short period of time after the exhaust has reached normal operating temper-atures.

ABOUT COMPANY

• BORLA PERFORMANCE INDUSTRIES 500 Borla Drive
• Johnson City TN, 37604-7523
• 805-986-8600

References

• Borla® - Performance Exhaust Systems, Mufflers & Induction

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>