Luoxi W-26 Magnetic Wireless Car Charger User Manual
- June 4, 2024
- Luoxi
Table of Contents
W-26 Magnetic Wireless Car Charger
User Manual
W-26 Magnetic Wireless Car Charger
Please Read This Completely And Keep It Properly
Product Introduction:
Thanksforyourchoosingourwirelesscharger, before you use this product, please
read this manual carefully and save it.
Product Overview
- Wireless charging center area
- LED
- Type-C input
- Air conditioning clip
- Multi-angle rotating ball fixing nut
User instruction
-
First, put the universal rotating ball head of the telescopic bracket of the empty suction cup on the fixed nut
-
Press the universal rotating ball head and nut into the main body.
-
Finally, tighten the nut as required.
-
Press the clip switch to insert the air outlet clip into the air conditioning port blade.
-
Adjust the appropriate angle and insert the Type-c cable into the wireless charger Type-C interface.
-
Plug the USB port into the adapter port, and put your phone on the emission area, make sure the receiving area of the mobile is magnetic suction with the emission area of the wireless charger.
Status light tip
- In standby mode the red and blue lights are on at the same time after power on, the blue light is off after 2 seconds, and the red light is off after 23 seconds;
- Charging mode: cha rgingthe mobile phone, the blue light keeps breathing and flashing, and the light is off when it is full; when the mobile phone leaves the wireless charging, the red light is on, and the red light is off after23 seconds, and it enters the standby state;
- FOD automatic foreign body detection: I intelligently identify foreign bodies, such as coins, keys, and other metal or magnetic items, and the red and blue lights flash alternately.
Standard accessories
- A manual (Including Warranty card, Certificate)
Product Parameters
| Product name | Magnetic Wireless Car Charger |
|---|---|
| Product model | W-26 |
| Input | 5.0V/2A;9.0V/2A;QC2.0/3.0 charger |
| Output | 5W;7.5W;10W;15W (Max) |
| Accepted distance | <5mm |
| Product size | 63.5X63.5X85mm |
| Wight | A–81g |
Attention
- Keep out of reach of children.
- Do not use the wireless charger in high-temperature humidity or corrosive environment, avoid damaging the circuit.
- .Do not disassemble the product without permission
- Do not put the magneticstriporchip care (ID card, bank card, etc.) near the charger to avoid a magnetic fault.
- 1t is recommended to use QCcertified adapters, and other QC adapters that meet international safety standards (9V/2A, 12V/2A);
- Thischargeronlysupports ‘Phone 12/13 series with magnetic wireless charging function.
- Thischargeronlycompatiblewith standard iPhone 12/13 series cases. Other magnet accessories may not be compatible with the charger;
FCC Caution:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
Thisdevicecomplieswith part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1)this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation. The device and its antenna(s)
must not be co-located or operating in conjunction with any other antenna or
transmitter.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one more of the
following measures: — Reorient or relocate the receiving antenna. Increase the
separation between the equipment and receiver. — Connect the equipment into an
outlet on a circuit different from that which the receiver is connected. —
Consult the dealer ran experienced radio/tv technician for help. To maintain
compliance with FCC’s CRF Exposureguidelines, Thisequipme should be installed
and operated with a minimum distance between 20cmthi radiator your body:
Useonlythesupplied antenna.
Warranty card
Customer data
User name:………………
Tel No.:………………………….
Address:………………………………..
E-mail:……………………………………….
Date of purchase:………………………………
FCC ID: 2ANCT-W26
Manufacturer: Shenzhen LuoxiTechnologyCo., Ltd
Address: 4F&6F, Building BI, Anle Industrial Zone, No.172, Hangcheng
Avenue, Hangcheng Street, Baoan District, Shenzhen, China
TEL : +086-0755-85278001
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>