BROMIC 3735106-NR Vertical Display Fridges and Freezers Instruction Manual
- June 13, 2024
- Bromic
Table of Contents
BROMIC 3735106-NR Vertical Display Fridges and Freezers
PREFIX
This manual contains important information about the installation, operation,
and maintenance of Bromic display chillers and freezers. Please pay close
attention to the important safety information shown throughout this
instruction manual. Any safety information will be accompanied by the
following safety alert symbols:
DANGER,
WARNING,
IMPORTANT
- READ THIS MANUAL CAREFULLY before installing or servicing this product.
- Improper installation, operation, or maintenance can result in death, severe injury, or property damage.
- Improper installation, operation, or maintenance may also result in warranty being voided.
- This appliance is intended for 220-240 Volt power supply.
- Installation and maintenance MUST be carried out as per instruction, in accordance with local regulation.
- Bromic will not accept liabilities, should the instructions incorporated in this manual be ignored.
IMPORTANT NOTES AND WARNINGS
- Read all instructions before installing or using this appliance.
- Retain this manual for future reference.
- Use this appliance only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury.
- Improper installation, adjustment or alteration and failure to follow the warnings and instructions in this manual could result in severe personal injury, death or property damage.
- The manufacturer is not responsible for any damage that could happen from improper use. The manufacturer emphasises that this appliance should be used in a responsible manner and that all procedures, warnings, and safety instructions contained in this booklet be followed strictly.
- Check for damage to the appliance regularly. If damage to the appliance is suspected, discontinue use immediately and contact the supplier or qualified person to repair.
- This appliance is not intended for use by people (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible of their safety.
- Keep packaging material out reach of children.
- Children should be carefully supervised to ensure that they do not play with the appliance.
- Do not attempt to alter the appliance in any manner.
- Please pay attention to the maximum load limit when filling the baskets.
- All work on electrical equipment must be carried out by a qualified and licensed technician only.
- Do not perform maintenance until the appliance has been turned off and power disconnected.
- Never detach any cover except where specifically instructed in this manual. Doing so might expose live electrical parts.
- Do not operate the appliance with panels, covers or guards removed.
- Keep the air intake and outlets free of obstructions.
- Do not use the appliance outdoors.
- If the supply cord becomes damaged, it must be replaced by an authorised service agent or similarly qualified person in order to avoid a hazard.
- If the appliance has not been used, or will not be used for a long period of time, disconnect power supply.
- Electrical equipment should not be placed under the unit or where refrigerant could gather in the event of a leak.
- Always use original spare parts supplied by the manufacturer
- When contacting Bromic Customer Service, ensure that you have the Model, Serial Number available. The information can be found from the rating plate which is located outside the appliance.
- Unplug the appliance before cleaning or moving it to avoid electric shock.
- Never use steam cleaner or wet cloths to clean the control panel, lighting and vent grills. This may damage the appliance or cause electric shock.
- The power plug must be accessible at all times while the appliance is running.
- The power supply must be properly earthed, consult a qualified electrician if unsure.
- Do not use extension cord or power adapter with this appliance.
- Do not use this appliance in an area with high humidity or subject to water damage.
Warning: Risk of fire / Flammable materials
- WARNING : The refrigerant used in this appliance is flammable, use caution during handling, servicing and disposal of the appliance.
- WARNING : Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
- WARNING : Keep clear of obstruction all ventilation openings in the appliance enclosure or in the structure for building-in.
- WARNING : Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
- WARNING : Ensure that the tubing of the refrigerant circuit is not damaged during transportation and installation, consult Authorised Personnel is unsure
- WARNING : If the refrigeration circuit becomes damaged. Avoid open flames and other source of ignition. Immediately disconnect the appliance from power supply. Ventilate the room and call Service Hotline.
- WARNING : Leaking refrigerant may cause eye injuries or could ignite.
- WARNING : The room for installing the appliance must be at least 1m³ per 8g of refrigerant. The amount of refrigerant in the appliance can be found on the rating plate attached to the appliance.
- WARNING : Do not use electrical appliances inside the food/ice storage compartments unless they are of the type recommended by the manufacturer.
- WARNING : In order to reduce flammability hazards, all service work of this appliance must only be carried out by an Authorised Service Person. In Queensland, the Authorised Service Person must hold a Gas Work Authorisation to service appliances containing Hydrocarbon refrigerant including removal of covers.
PRODUCT OVERVIEW
| GM0220-NR| GM0330-NR| GM0374-NR| GM0374L-NR
---|---|---|---|---
Part Number| 3736033-NR| 3736034-NR| 3736035-NR| 3736036-NR
| Height, mm| 1400| 1725| 1950| 2100
External Dimension| Width, mm| 595| 595| 595| 595
| Depth, mm| 640| 640| 640| 640
Capacity| Litres| 215| 290| 372| 372
Gross Weight| Kg| 63| 68| 81| 87
Display lightbox| Type| | | | Yes
Temp. Range| Degree Celsius| +1 to +5°C| +1 to +5°C| +1 to +5°C| +1 to
+5°C
**Climate Class*| Class| 4| 4| 4| 4
Max Ambient| Degree Celsius| 40°C| 40°C| 40°C| 40°C
Main Light| Type| LED| LED| LED| LED
Door Shape| Type| Flat| Flat| Flat| Flat
Safety Glass Door| Type| Yes| Yes| Yes| Yes
Self-Closing Door| Type| Yes| Yes| Yes| Yes
Shelves| Qty| 3+base| 4+base| 5+base| 5+base
Castor| Type| Yes| Yes| Yes| Yes
| Refrigerant| R600a| R600a| R600a| R600a
| Charge, g| 70| 70| 70| 70
Plug| Rating| 10A| 10A| 10A| 10A
Colour| Colour| White with Silver Trim| White with Silver Trim| White
with Silver Trim| White with Silver Trim
Extra Care Warranty**| Years| 2| 2| 2| 2
- Climate class 3 refers to 25°C dry bulb temperature, 60% relative humidity; Climate class 4 refers to 30°C dry bulb temperature, 55% relative humidity;
Part Number| | 3736092-NR| 3736037-NR| 3736038-NR| RETRO
3736079-NR
---|---|---|---|---|---
| Height, mm| 2100| 2100| 2125| 1720
External Dimension| Width, mm| 595| 595| 680| 595
| Depth, mm| 640| 640| 655| 610
Capacity| Litres| 372| 380| 438| 290
Gross Weight| Kg| 87| 90| 112| 74
Display lightbox| Type| Yes| Yes| Yes|
Temp. Range| Degree Celsius| +1 to +5°C| +1 to +5°C| +1 to +5°C| +1 to
+5°C
**Climate Class*| Class| 4| 4| 4| 4
Max Ambient| Degree Celsius| 40°C| 40°C| 40°C| 40°C
Main Light| Type| LED| LED| LED| LED
Door Shape| Type| Flat| Curved| Flat| Flat
Safety Glass Door| Type| Yes| Yes| Yes| Yes
Self-Closing Door| Type| Yes| Yes| Yes| Yes
Shelves| Qty| 5+base| 5+base| 5+base| 4+base
Castor| Type| Yes| Yes| Yes| Yes
| Refrigerant| R600a| R600a| R600a| R600a
| Charge, g| 70| 70| 110| 70
Plug**| Rating| 10A| 10A| 10A| 10A
- Climate class 3 refers to 25°C dry bulb temperature, 60% relative humidity; Climate class 4 refers to 30°C dry bulb temperature, 55% relative humidity;
| | WC0400C-NR| UC0374SDW -NR| UF0374-NR| UF0374LS-NR
---|---|---|---|---|---
Part Number| | 3735145-NR| 3735127-NR| 3736045-NR| 3736046-NR
| Height, mm| 1840| 1925| 1925| 2100
External Dimension| Width, mm| 595| 595| 595| 595
| Depth, mm| 640| 640| 620| 620
Capacity| Litres| 372| 372| 300| 300
Gross Weight| Kg| 83| 90| 96| 100
Display lightbox| Type| | | | Yes
Temp. Range| Degree Celsius| +2 to +14°C| +1 to +5°C| -22 to -18°C| -22
to -18°C
**Climate Class*| Class| 4| 4| 4| 4
Max Ambient| Degree Celsius| 40°C| 40°C| 35°C| 35°C
Main Light| Type| LED| Fluorescent| LED| LED
Door Shape| Type| Curved| Flat| Flat| Flat
Safety Glass Door| Type| Yes| Solid door| Yes| Yes
Self-Closing Door| Type| Yes| Yes| Yes| Yes
Shelves| Qty| 5+base| 6+base| 6+base| 6+base
Castor| Type| Yes| Yes| Yes| Yes
| Refrigerant| R600a| R600a| R290| R290
| Charge, g| 70| 70| 85| 85
Plug| Rating| 10A| 10A| 10A| 10A
Colour| Colour| Silver| White with Black Details| White with Silver
Trim| White with Silver Trim
Extra Care Warranty**| Years| 2| 2| 2| 2
- Climate class 3 refers to 25°C dry bulb temperature, 60% relative humidity; Climate class 4 refers to 30°C dry bulb temperature, 55% relative humidity;
| UF0440LS-NR| UF0374SDS-NR
---|---|---
Part Number| | 3736047-NR| 3735106-NR
| Height, mm| 2133| 1925
External Dimension| Width, mm| 680| 595
| Depth, mm| 655| 640
Capacity| Litres| 440| 300
Gross Weight| Kg| 123| 97
Display lightbox| Type| Yes|
Temp. Range| Degree Celsius| -22 to -18°C| -22 to -18°C
**Climate Class*| Class| 4| 4
Max Ambient| Degree Celsius| 35°C| 35°C
Main Light| Type| LED| Fluorescent
Door Shape| Type| Flat| Flat
Safety Glass Door| Type| Yes| Solid door
Self-Closing Door| Type| Yes| Yes
Shelves| Qty| 6+base| 6+base
Castor**| Type| Yes| Yes
- Climate class 3 refers to 25°C dry bulb temperature, 60% relative humidity; Climate class 4 refers to 30°C dry bulb temperature, 55% relative humidity;
INSTALLATION
Locating the Cabinet
Ensure the following instructions are observed as this is vital for proper and trouble-free operation.
- Do not install the cabinet outdoors.
- Locate the appliance in a dry and well ventilated place.
- The unit must be positioned on a level surface.
- Do not install in the vicinity of heating radiators or other heat sources.
- Do not install the appliance where it is exposed to direct sunlight.
- Do not install the appliance where it is exposed to warm draughts or open doors.
- Keep the ventilation grill free of obstructions.
- Adequate allowance should be made for door openings.
Ventilation
- Allow 150mm clearance between walls, ceiling and the appliance. This is essential for optimal performance and reliability
Power Supply
- The appliance must not be plugged into a multiple outlet power board.
- The appliance is supplied with a flexible power cord fitted with a 3-pin plug.
- The socket used must be properly earthed and fuse/RCD protected.
- See the rating label inside the cabinet for supply voltage, frequency and current draw.
- Power cable should not be placed next to heat source such as room heater or other electrical appliance.
- Do not turn off power before consulting the person responsible.
- Mark the power source clearly, so the refrigerator is not unplugged or turned off accidentally.
Before Operating
- Avoid tilting or transporting the appliance in a horizontal position. If the appliance were to be tilted, it must be left to stand in an upright position and not plugged in for at least 6 hours.
- Remove all the packaging material before using the appliance.
- Start the appliance only if it has been installed as described.
OPERATION
Start-up
- Connect the appliance to the mains power supply, the appliance will start working without requiring further operation.
- The thermostat has been pre-set by factory, there is no need to adjust unless requiring different internal temperature.
Using the Thermostat
- Adjust the thermostat to set appliance’s internal temperature, moving clock-wise (towards larger number) to achieve lower internal temperature. NOTE: You should only make small adjustment and wait 24 hours to see whether further adjustment is required.
Digital thermometer
- The digital thermometer measures and displays the internal temperature. The battery should be replaced when the brightness of the LCD display appears to be weak or dim.
PRODUCT LOADING AND STORAGE
IMPORTANT: Run the refrigerator for at least 24 hours before loading
WARNING : WARNING: Do not store explosive substances such as aerosol cans with a flammable propellant inside the appliance.
Start-up
- Clean the interior surface with a soft cloth and warm water before loading.
- Ensure there is free circulation of air between the products.
- Do not overstock the appliance.
- Keep refrigerator door openings to a minimum.
- Maximum recommended shelf load (for each shelf) is specified in section 3 of this manual. Do not overstock.
NOTE: Bromic cannot be responsible for loss of stock or damage to stock.
MAINTENANCE
WARNING : Disconnect the appliance from the power supply before performing any maintenance. Never unplug the appliance by pulling on the cord. Always grasp the plug firmly and pull straight out of the outlet.
WARNING : Exposure to significant water ingress will void warranty and cause potential safety issues. If the unit should be exposed to water, please contact the manufacturer immediately.
IMPORTANT : Warranty may be void if there is no evidence of preventative maintenance is performed on the appliance.
Cleaning the Cabinet
- Remove the products and transfer to a suitable location prior to cleaning the inside of the cabinet.
- Do not use any aggressive or abrasive cleaning agents.
- Never use a water hose or a high-pressure jet to clean.
- Do not use sharp or pointed objects for cleaning.
- Clean the inside and outside of the appliance with a clean damp cloth or with a neutral cleanser.
- Dry all surfaces with a dry cloth.
Defrosting
- The freezer should be defrosted when ice is approximately 5mm thick. A thick layer of ice built-up may reduce the freezer’s cooling capacity and increase energy consumption.
- To ensure correct operation of the appliance, we recommend to defrost at least twice a year.
- Plan your defrosting in advance, preferably when there is no or limited stock in the freezer.
- Disconnect the appliance from power supply to start defrosting.
- Never use electric heater, warm water or hairdryers for defrosting.
- Clean the internal with dry cloths once defrosting is finished.
- Plug the appliance back in to resume normal working condition.
TROUBLESHOOTING
IMPORTANT : Repairs on the unit must be carried out by an authorised and licensed person only. Contact the manufacturer or an approved service agent for any repairs needed.
Symptom | Possible Cause(s) | Solution |
---|---|---|
Unit does not work | A. No power supply | A. Check power supply and green |
indicator
B. Adjust temperature control dial to a colder position
Internal Temperature Too High| A. Ambient temperature too high
B. Inadequate ventilation
C. Wall clearances below minimum distance
D. Incorrect dial position
E. Ice build-up on internal walls| A. Relocate unit
B. Keep ventilation slots free
C. Adjust to minimum clearance
D. Adjust temperature control dial
E. Defrost the appliance manually, ensure door is closed properly
Internal Temperature Too Low| A. Set temperature too low| A. Adjust
temperature control dial
Odour inside cabinet| A. Cabinet dirty| A. Clean
Lid difficult to open| A. Normal
B. Hinge damage| A. It is normal for the lid to be difficult to open just
after you closed it
B. Inspect hinge and call service hotline
Noisy| A. Unlevel surface| A. Relocate unit
Thermometer LCD dim / off| A. Battery dead| A. Replace battery
ENVIRONMENTAL AND DISPOSAL NOTES
These refrigerated cabinets are designed to high standards of environmental
protection and recycling convenience. Cyclopentane, an environmentally
friendly foaming agent, has been used. Cyclopentane is distinguished by zero
ozone depletion potential (ODP) and zero global warming potential (GWP).
The refrigerant used and contained within a hermetically tight circuit is
environmentally friendly and does not contain chlorine and zero ODP.
The device must be disposed of in accordance with applicable regulations. The
WEEE regulations must be observed.
In the interest of preventing environmental nuisance and promoting re-use of
the high quality materials employed, used refrigeration equipment must be
collected for expert disposal and recycling. Therefore, observe the following
disposal regulations:
-
The cabinet must not be discarded with regular waste.
-
The refrigeration circuit must not be damaged.
-
Before disposal, make it unserviceable by disconnecting the power plug and cutting off the power cable.
-
Consult your local authorities or authorised dealers for details of collection and disposal facilities.
-
Children are often unable to recognise the dangers associated with refrigeration equipment.
Proper supervision must be maintained and children must be prevented from playing with discarded refrigerated cabinets. -
The refrigerant used in this appliance is flammable. The refrigeration circuit must not be damaged.
Warning: Risk of fire / Flammable materials
WARRANTY
All Bromic products are manufactured to the highest quality standard and are supported by our Extra Care Service Warranty, including guarantees against any material or workmanship defects; guarantees that cannot be excluded under Australian Consumer Law.
Warranty Terms vary across the range. Please ensure you are familiar with the
Terms and Conditions that apply to the purchase of your Bromic product by
referring to the Warranty Policy included with your purchased product.
Alternatively, you can also download the Warranty Policy at
www.bromicgroup.com/warranty-information
HOW TO PLACE A SERVICE REQUEST
- Please call 1300 276 642 to place a warranty service request and let the operator know whether you need Priority A or B service. More information can be found below.
- Ensure you have the serial number of your product ready before contacting us.
- The serial number of your product can be found on a compliance plate located on the inside right and at the rear of your cabinet.
SERVICE REQUEST PRIORITY
PRIORITY A SERVICE
When the unit is NOT performing its primary function such as cooling or
heating, or presents an OH&S or food safety risk
PRIORITY B SERVICE
When the unit is performing its primary function, and presents no OH&S or food
safety risk. i.e. lights, gaskets. locks, door adjustment
SERVICE CALL PLACED BEFORE MIDDAY
Priority A – Technician to attend site within 4 hours
Priority B – Technician to attend site within 8 business hours
SERVICE CALL PLACED AFTER MIDDAY
Priority A – Technician attends site before midday on the following business
day
Priority B – Technician attends site before 4pm on the following business day
Customer Support
BROMIC REFRIGERATION
10 Phiney Place, Ingleburn (Sydney)
NSW 2565 Australia
T. 1300 276 642
For further product information
bromicrefrigeration.com.au
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>