WEISER GED240 Elements Contemporary Keypad Deadbolt Installation Guide

Installation and User Guide
53765-001
Rev 01
GED240
Weiser Technical Support | 1-800-501-9471 | www.weiserlock.com

Required tools

https://sj83t.app.goo.gl/FDPj

Parts in the box

Prepare the door and check dimensions

If drilling a new door, use the supplied template and the complete door drilling instructions.

A Measure to confirm that the hole in the door is either 54 mm (2-1/8 in) or 38 mm (1-1/2 in).
Note: Additional door preparation may be required for doors with 38 mm (1-1/2 in ) holes.

B Measure to confirm that the backset in either 60 or 70 mm (2-3/8 or 2-3/4 in).

C Measure to confirm that the hole in the door edge is 25 mm (1 in).

D Measure to confirm that the door is between 35 mm and 44 mm (1-3/8 and 1-3/4 in) thick.

Note: Please contact customer service if door thickness exceeds 44mm (1-3/4 in) for a thick door kit.

Install the latch and strike

A Hold the latch in front of the door hole, with the latch face flush against the door edge.

Is the rectangular shaped hole centered in the door hole?

No adjustment is required.
Proceed to next step.

|

Rotate latch face as shown to extend latch.

---|---

B Is the door edge chiselled?

Install latch in door with supplied screws.

|

Use a flathead screwdriver to remove latch face. Once removed, grip the latch with one hand and with the other hand twist collar off. Install drive-in collar.

---|---

C Install strike on the door frame.
**** Make sure the hole in the door frame is drilled a minimum of 25 mm (1 in) deep.

D **IMPORTANT:** Make sure the latch bolt is fully retracted (in the unlocked position).

Install the exterior keypad

What is the diameter of the hole in the door?

Diameter is 54 mm (2-1/8 in)

Adapter ring is required for installation.

| Diameter is 38 mm (1-1/2 in)

Adapter ring is not needed for installation.

---|---

B Locate screws for step 3C and keep them within reach.

C Install exterior keypad and mounting plate.

Insert key and test latch. If latch does not extend or retract smoothly, adjust screws.
Remove key when finished and make sure the latch bolt is FULLY EXTENDED.

Install the interior assembly

A Remove interior cover from interior assembly.

a Check to make sure the latch bolt is in the extended/locked position to install the interior assembly.

| b Make sure turnpiece shaft is rotated as shown.

---|---
c Remove the interior cover from the interior assembly.

| d Do not install batteries until step 5.

B Secure the interior assembly onto the mounting plate.

a

Connect the cable.
Ensure a tight cable connection.

| b Route cable around the side notch and bottom of the interior assembly.

---|---
c Insert the flat blade into the unpiece shaft.

| d **** Ensure you are using the correct screws. Using incorrect screws will
damage the product.

Install the batteries in the interior assembly

A Install 4 AA batteries in interior assembly

Ensure your door is open while installing batteries.
Ensure the interior cover is off to install batteries.
Note: Batteries are not included

**** Ensure correct polarity.
For best results, use new, non-rechargeable alkaline batteries only.

B Install interior cover for the interior assembly.

Add user codes (12 max)

During User Code programming, a time out will occur if the keypad is not pressed for 5 seconds and you will need to restart the procedure.
**** For security reasons, the first 4 digits of each User Code must be unique. For example, you are unable to program a user code 1-2-3-4-5 as well as user code 1-2-3-4-6.

A Make sure the interior cover is off.

B Press the Program button once .

C Press button once.

D Enter user code. A total of 12 user codes may be programmed. User codes should be 4 to 8 digits in length.

E Press button again.

Note: After the first User Code is created, the latch bolt will automatically retract and extend to learn the locking and unlocking direction of the door.
The lock button will indicate success or failure.
GREEN: Success RED: Unsuccessful

Test the lock (review normal operation)

**** Before you can lock and unlock the door a User Code must be created. Refer to Step 6 for instructions how to create a User Code.
Confirm that the code(s) added in previous step can unlock the door.

A To lock your door, press the lock button. The lock will beep twice and the lock button will flash amber as the deadbolt extends.

B To unlock your door, enter the user code. The lock will beep twice and the lock button will flash green as the deadbolt retracts.

Adding a One-time User Code

1. Remove interior cover.
Press programming button.![WEISER GED240 Elements Contemporary Keypad Deadbolt

• Adding a One-time User Code 1](https://manuals.plus/wp- content/uploads/2023/10/WEISER-GED240-Elements-Contemporary-Keypad-Deadbolt- Adding-a-One-time-User-Code-1.jpg)| 2. Press number .

| 3. Press number .

---|---|---
4. Press the button.

| 5. Enter the one time user code.

| 6. Press the button again.

Up to 2 One-time User Codes can be saved. One-time User Codes should be 4 to 8 digits in length.
The One-Time User Code will be deleted automatically after it is used. The same One-Time User Code can be created again after it’s used.

Delete a Single User Code

1. Remove interior cover.
Press programming button.| 2. Press number .

| 3. Press the button.

---|---|---
4. Enter the user code you want to delete.

| 5. Press the button again.

| 6. Enter the user code being deleted again.

7. Press the button again.

| If unsuccessful:
Make sure you entered the same user code in steps 4
and 6.
Test code while the door is open. Test the User Code
to make sure it no longer unlocks the door.|

If a button is not pressed within 5 seconds, the system will time out, and you will need to restart the procedure.

Enable/ Disable Audio

1. Remove interior cover.
Press programming button.| 2. Press number .

---|---
3. Press number again .

| 4. Press the button.

Note: LED status indicator will still function once audio is disabled. Repeat the programming steps to enable the audio.

Enable/ Disable User Codes

1. Remove interior cover.
Press programming button.| 2. Press number .

---|---
3. Press number .

| 4. Press the button.

Enable/ Disable Auto-Lock

1. Remove interior cover.
Press programming button.| 2. Press number .

---|---
3. Press number .

| 4. Press the button.

Change Auto-Lock Time Delay

1. Remove interior cover.
Press programming button.| 2. Press number .

| 3. Press number .

---|---|---
4. Press the button.

| 5. Choose and press button for delay.

30 seconds
1 minute
3 minutes
5 minutes
10 minutes

| 5. Press the button again.

Door Rehanding

1. Remove interior cover.
Press programming button.| 2. Press number .

| 3. Press the button.

---|---|---

The latch bolt will extend and retract to learn the orientation of the door.
Note: Perform this process for the lock to learn the locking and unlocking direction of the door.
This feature is used for the lock to learn the orientation of your door (left- or right-handed). If stuck/jammed bolt error continues to occur after performing this step, please make sure there is no obstruction from strike or door jamb to prevent the bolt from extending.

Factory Reset

Note: Lock must be in a unlocked position to factory reset.

1. Remove interior cover.
PRESS and HOLD programming button for 15 seconds.| 2. The lock will have a long beep.

| 3. Press programming button once more.

---|---|---

A factory reset will delete all User Codes and change all programming to factory settings. At this time, the lock can only be locked or unlocked manually with the key.

Add/ Change Programming Code

1. Remove interior cover.
Press programming button.| 2. Press number .

---|---
3. Press the button.

| 4. Enter Programming Code.

5. Press the button again.

|

Enable/ Disable Programming Code:
Optional: A Programming Code enables you to make programming changes without needing to access the Programming Button. This is ideal for landlords to program the lock without
access to the interior programming button.
Note: Once Programming Code is enabled, the Programming Button is disabled and can only be used to factory reset the lock.
One Programming Code between 4 to 8 digits can be saved and cannot be the same as any
User Code and cannot be used as a User Code to unlock the lock.
To program the lock with Programming Code:

To disable Programming Code:

Deadbolt at a Glance

|
---|---

System Alerts

minute, check code,
and retry
Stuck/Jammed ammed bolt| RED/
WHRE Flash x5| 5 beeps| Clear jam and try again
Factory Reset Successful| Flashes GREEN x1| 1 beep|
Factory Reset Unsuccessful| Flashes RED x3| 3 beeps| Retry factory reset steps.
Make sure to press the
Programming Button one
more time within 10 seconds
after the long beep.
Programming Successful| Flashes GREEN x1| 1 beep|
Programming Unsuccessful| Flashes RED x3| 3 beeps| Review Programming steps

Important Safeguards

1. Read all instructions in their entirety.
2. Familiarize yourself with all warning and caution statements.
3. Remind all family members of safety precautions.
4. Always have access to your lock’s standard key.
5. If using the Auto-Lock features, make sure you have your standard key with you to prevent locking yourself out.
6. Familiarize yourself with the system alerts.
7. Replace low batteries immediately.
8. Dispose of used batteries according to local laws and regulations.

WARNING:
This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property.  No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional.

CAUTION:
Prevent unauthorized entry. Since anyone with access to the back panel can change the User Codes, you must restrict access to the back panel and routinely check the User Codes to ensure they have not been altered without your knowledge. The use of a programming code can help protect your system’s settings.

© 2022 Spectrum Brands, Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>