Weiser GED250 Powerbolt 3 Electronic Deadbolt Installation Guide

June 13, 2024
Weiser

Weiser GED250 Powerbolt 3 Electronic Deadbolt

Weiser GED250 Powerbolt 3 Electronic Deadbolt

Required Tools

  • Batteries

  • Ruler

  • Screwdrivers

Additional Tools (depending on application)

  • Hammer

  • Wood block

Parts in the box

  • Latch

  • Interior Assembly

  • Exterior Assembly

  • Adapter Ring

  • Mounting Plate

  • Collar

  • Keys

  • For Latch / Strike
    Strike

Parts in the box

  • For Lock
    SmartKey Tool

Parts in the box

Prepare the door and check dimensions

If drilling a new door, use the supplied template and the complete door drilling instructions available at www.kwikset.com/doorprep.

A Measure to confirm that the hole in the door is either 54 mm (2-1/8 in) or 38 mm (1-1/2 in).

Note: Additional door preparation may be required for doors with 38 mm (1-1/2 in ) holes.

B Measure to confirm that the backset either 60 or 70 mm (2-3/8 or 2-3/4 in).

C Measure to confirm that the hole in the door edge is 25 mm (1 in).

D Measure to confirm that the door is between 35 mm and 44 mm (1-3/8 and 1-3/4 in) thick.

Note: Please contact customer service if door thickness exceeds 44 mm (1-3/4 in) for a thick door kit.

Install the latch and strike

For Latch / Strike Bag

A Hold the latch in front of the door hole, with the latch face flush against the door edge.

B Is the door edge chiselled?

2 Install the latch and strike

C Install strike on the door frame.

Make sure the hole in the door frame is drilled a minimum of 25 mm (1 in) deep.

Install the latch and strike

D IMPORTANT: Make sure the latch bolt is fully retracted (in the unlocked position).

Install the latch and strike

Install the exterior keypad

For Lock Bag

A What is the diameter of the hole in the door?

Install the exterior keypad

B Locate screws for step 3C and keep them within reach.

52367
(2x)
(For Lock Bag)

C A Install exterior keypad and mounting plate.

Install the exterior keypad

Install the interior assembly

For Lock  Bag

A Remove interior cover from interior assembly.

  • a. Check to make sure the latch bolt is in the extended/locked position to install the interior assembly.

  • b.  Make sure turnpiece shaft is rotated as shown.

If the turnpiece is not pointing up, rotate the turnpiece until you hear a click.

  • c. Remove the interior cover from the interior assembly

  • d. Do not install batteries until step 5.

B Secure the interior assembly onto the mounting plate

b. Route cable around the side notch and bottom of the interior assembly.

c. Insert the flat blade into the turnpiece shaft.

d. Ensure you are using the correct screws. Using incorrect screws will damage the product.

Install the batteries in the interior assembly

A Install 4 AA batteries in interior assembly

Install the batteries in the interior assembly

B Install interior cover for the interior assembly.

Add user codes (25 max)

During programming, if no button is pressed within 5 seconds, the system will time out and you will need to restart the procedure

For security reasons, the first 4 digits of each User Code must be unique. For example, you are unable to program a user code 1-2-3-4-5 as well as user code 1-2-3-4-6.

  • A Make sure the interior cover is off. Press the Program button once.

  • B Press number 1.

  • C Press Weiser logo once

  • D Enter user code. A total of 25 user codes may be programmed. User codes should be 4 to 8 digits in length.

  • E Press Weiser logo once

Note: After the first User Code is created, the latch bolt will automatically retract and extend to learn the locking and unlocking direction of the door. The Kwikset logo will indicate success or failure. GREEN: Success RED: Unsuccessful

Test the lock (review normal operation)

Before you can lock and unlock the door, a User Code must be created. Refer to Step 6 for instructions how to create a User Code.  Confirm that the code(s) added in previous step can unlock the door.

A To lock your door, press the Weiser logo button. The lock will beep twice and the Weiser logo button will flash amber as the deadbolt extends

Test the lock \(review normal operation\)

B To unlock your door, enter the user code. The lock will beep twice and the Weiser logo button will flash green as the deadbolt retracts.

Test the lock \(review normal operation\)

Adding a One-time User Code

  1. Remove interior cover. Press programming button.

  2. Press number 7.

  3. Press the Weiser logo button.

  4. Enter the one time user code.

  5. Press the Weiser logo button.

Up to 5 One-time User Codes can be saved. One-time User Codes should be 4 to 8 digits in length. The One-Time User Code will be deleted automatically after it is used. The same One-Time User Code can be created again after it’s used.

Delete a Single User Code

  1. Remove interior cover. Press programming button.

  2. Press number 2.

  3. Press the Weiser logo button.

  4. Enter the user code you want to delete.

  5. Press the Weiser logo button.

  6. Enter the user code being deleted again.

  7. Press the Weiser logo button again.

If unsuccessful: Make sure you entered the same user code in steps 4 and 6.

Test code while the door is open. Test the User Code to make sure it no longer unlocks the door.

If a button is not pressed within 5 seconds, the system will time out, and you will need to restart the procedure.

Delete ALL User Codes

Note: Keypad locking function will be disabled when User Codes are deleted. The lock can only be operated manually by a key during this time.

  1. Remove interior cover. Press programming button.

  2. Press number 4.

  3. Press the Weiser logo button.

  4. Press number 4.

  5. Press the Weiser logo button.

Enable/ Disable Audio

  1. Remove interior cover. Press programming button.

  2. Press number 5.

  3. Press the Weiser logo button.

Note: LED status indicator will still function once audio is disabled. Repeat the programming steps to enable the audio.

Enable/ Disable User Codes

Note: When all User Codes are disabled, all electronic functions will be disabled as well. The door must be locked or unlocked manually with the key. Repeat the programming steps to enable the User Codes.

  1. Remove interior cover. Press programming button.

  2. Press number 6.

  3. Press the Weiser logo button.

Enable/ Disable Auto-Lock

  1. Remove interior cover. Press programming button.

  2. Press number 9

  3. Press the Weiser logo button.

Repeat the programming steps to disable the auto-lock.

Change Auto-Lock Time Delay

  1. Remove interior cover. Press programming button.

  2. Press number 8.

  3. Press the Weiser logo button.

  4. Choose and press button for delay.
    30 seconds
    1 minute
    3 minutes
    5 minutes
    **** 10 minutes

  5. Press the Weiser logo button.

Door Rehanding

  1. Remove interior cover. Press programming button.

  2. Press number 0.

  3. Press the Weiser logo button.

The latch bolt will extend and retract to learn the orientation of the door.

Note : Perform this process for the lock to learn the locking and unlocking direction of the door. This feature is used for the lock to learn the orientation of your door (left- or right-handed). If stuck/jammed bolt error continues to occur after performing this step, please make sure there is no obstruction from strike or door jamb to prevent the bolt from extending.

Factory Reset

Note: Lock must be in a unlocked position to factory reset.

  1. Remove interior cover. PRESS and HOLD programming button for 15 seconds.

  2. The lock will have a long beep.

  3. Press programming button once more.

A factory reset will delete all User Codes and change all programming to factory settings. At this time, the lock can only be locked or unlocked manually with the key

SmartKey Re-Keying

Re-key the lock to work with your existing kw1 key. See the supplied SmartKey Re-key instructions for more information.
Note: If Auto-Lock is enabled remove batteries before re-keying your lock.

Add/ Change Programming Code

  1. Remove interior cover. Press programming button.

  2. Press number 3

  3. Press the Weiser logo button.

  4. Enter Programming Code.

  5. Press the Weiser logo button.

Enable/ Disable Programming Code:

Optional: A Programming Code enables you to make programming changes without needing to access the Programming Button. This is ideal for landlords to program the lock without access to the interior programming button.

Note: Once Programming Code is enabled, the Programming Button is disabled and can only be used to factory reset the lock.

One Programming Code between 4 to 8 digits can be saved and cannot be the same as any
User Code and cannot be used as a User Code to unlock the lock.

To program the lock with Programming Code:

Programming Code

Powerbolt at a Glance

System Alerts

Action Lights Sounds Troubleshoot
Successful  Unlock Flashes GREEN x2 2 beeps
Successful Lock Flashes AMBER x2 2 beeps
Low battery Flashes RED xl 0 10 beeps Install fresh new batteries
Incorrect User Code Flashes RED x 3 3 beeps Check code, and retry
Exceed 3 incorrect User Code attempts Flashes RED xl 5 15 beeps Wait 1

minute, check code, and retry
Stuck/Jammed bolt| Alternate RED/ WHITE Flash xS| 5 beeps| Clear jam and try again
Factory Reset Successful| Flashes GREEN xl| 1 beep|
Factory Reset Unsuccessful| Flashes RED x3| 3 beeps| Retry factory reset steps. Make sure to press the Programming Button one more time within 10 seconds after the long beep.
Programming Successful| Flashes GREEN xl| 1 beep|
Programming Unsuccessful|

Flashes RED x3

|

3 beeps

|

Review Programming steps

Important Safeguards

  1. Read all instructions in their entirety.
  2. Familiarize yourself with all warning and caution statements.
  3. Remind all family members of safety precautions.
  4. Always have access to your lock’s standard key.
  5. If using the Auto-Lock features, make sure you have your standard key with you to prevent locking yourself out.
  6. Familiarize yourself with the system alerts.
  7. Replace low batteries immediately.
  8. Dispose of used batteries according to local laws and regulations.

WARNING:
This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional.

CAUTION:
Prevent unauthorized entry. Since anyone with access to the back panel can change the User Codes, you must restrict access to the back panel and routinely check the User Codes to ensure they have not been altered without your knowledge. The use of a programming code can help protect your system’s settings.

3D instructions available on
QR Code

SCAN FOR BILT® 3D INSTRUCTIONS


POWERED BY BILT INTELLIGENT INSTRUCTIONS®

Weiser Technical Support | 1-800-501-9471 | www.weiserlock.com

Weiser Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals