BOSCH FMR-5000-C Remote Keypad Installation Guide
- June 13, 2024
- Bosch
Table of Contents
BOSCH FMR-5000-C Remote Keypad Installation Guide
Installations Instructions
Product Overawe
WARNING!
Live components and stripped cable! Risk of injury from electric shock. The
system must be current-free during connection work.
NOTICE!
Installation must only be performed by authorized and specialized personnel!
Functional Description
The Remote Keypad can be used to perform the same operating procedures as the control panel, enabling variable operation of a networked system. It has the following functional elements (see Figure 1, Page 4):
| Pos. | Designation | Function |
|---|---|---|
| A | Touch screen | Operating the networked system through virtual buttons and |
variable display windows
B| 22 fixed buttons| Standard entries
C| 11 LEDs| Indicating the operating status
D| Key switch| 2 switch settings, freely programmable, e.g. for switching
between day/night mode or connecting/disconnecting for local alarm signaling
E| Reboot button| Remote Keypad HW reset
F| 6-pin DIP switch| Configuration
G| 3 rotary switches| Address setting
Installation
Follow the mounting instructions according to the mouting variant for your application.
Before mounting the housing, remove the operating unit. This prevents the touch screen being damaged and facilitates installing the lower mounting screws.
Wiring
- Connect the shield wires to the screw terminal (Figure 11, Page 13 (step 1).
- Fasten the cables with cable ties (Figure 11, Page 13, step 1 to 4).
The Remote Keypad has
- 2 CAN interfaces (CAN1/CAN2) for networking
- 2 Ethernet interfaces (ETH1/ETH2) for networking
- 2 signal inputs (IN1/IN2)
- 1 USB and 1 RS232 interface
Consider the maximum cable length of 2 m when using the USB and RS232 interfaces (see Figure 10, Page 12).
NOTICE!
You will find detailed information about the CAN and Ethernet networking of
the fire panels in the Networking Guide available for download at
www.boschsecurity.com.
CAUTION!
If Ethernet networking is planned, the Remote Keypad must be grounded.
Address Setting and Configuration
- Assign a unique physical address to each Panel Controller and Remote Keypad by setting the rotary switches and write it down on the label (see Figure 13, Page 15, step 1 and 2).
- For configuration, set the 6-pin DIP switch (see Figure 13, Page 15, step 3).
- Mark the setting on the provided label (step 4).
Technical Data
LCD Ddisplay / touch screen| LCD display with 320 x 240 pixels, touch screen
with 127,5 mm x 170 mm active surface
---|---
Operating and display elements| 22 buttons, 1 key switch, 11 LEDs, 1 Reboot
button
Interfaces| CAN1, CAN2, ETH1, ETH2, USB, RS232
Signal inputs| IN1/IN2
Permissable length of CAN cable for system networking| Lmax = 1000 m,
depending on configuration, cable type and topology
Power supply connection| DC1 (power supply), DC2 (redundant power supply)
Input voltage| 12 V DC to 30 V DC, from FPA-5000 or FPP-5000
Maximum line restance of power supply| 18 Ω
Maximum current consumption| – Standby operation: 140 mA at 24 V
DC- During an alarm: 230 mA at 24 V DC
Permissible operating temperature| -5 °C to +50 °C
Permissible storage temperature| -20 °C to +70 °C
Housing material and color| ABS plastic, light gray (similar RAL 7035)
Dimansions (H x W x D)| 280 mm x 340 mm x 87 mm
Weight| Approx. 3 kg
Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
www.boschsecurity.com
© Bosch Sicherheitssysteme GmbH, 2012
