ITECH 3-In-One Charger User Manual

June 4, 2024
iTech

3-IN-ONE CHARGER
USER MANUALITECH 3 In One Charger -

ITECH® 3-IN-ONE

ITECH 3 In One Charger - IT

  1. USB-A Output
  2. USB-C Input (power supply not provided)
  3. Qi® Wireless Charging Pad #1
  4. Qi® Wireless Charging Pad #2
  5. iTech Charger Pass-through slot

OPERATING INSTRUCTIONS

PREPARING TO CHARGE
Supports smartphones with a protective case up to 4mm thick. If your protective case is metallic or has magnetic plates, you must remove the case before placing your phone on the charging pad.
Place the iTech Charger inside the Pass-through slot 5 and plug it into the USB-A output 1.

CHARGING

  • Connect the Wireless Charger using the included USB-C power cable to a UL-listed power supply (power supply not provided)
  • Place your Qi®-enabled smartphone in the center of Wireless Pad #1. Your smartphone will automatically begin to charge.
  • Place your Qi® enabled wireless earbud case on Wireless Pad #2. Your earbud case will automatically begin to charge.

FAST CHARGING
Enable Fast Charging (up to 10W) for your device by using a UL-listed USB charger with Quick Charge 3.0 Technology (5V/3A, 9V/2A).

TROUBLESHOOTING

No power: First make sure you plugged the USB cord into the correct ports. Then try using a different cable.
The device isn’t charging: Make sure your device supports wireless charging and is in the center of the Charging Pad.
Watch isn’t charging: Make sure the watch charger cable is connected to the USB-A Output (1) and that the charger pins align with the connectors on the watch.

ITECH 3 In One Charger - connectors on the watch

REGULATORY NOTICES

FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

REGULATORY NOTICES (continued)
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure requirements, please follow operations instructions as documented in this manual.
This equipment should be installed and operated with a minimum distance of 10cm between the radiator and your body.
Industry Canada Statement: This device complies with RSS216 of the Industry Canada Rules.
Operation is subject to two conditions: (1)
This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 10cm between the radiator and your body.
Innovation, Science & Economic Development Canada Statement: This digital apparatus complies with CAN ICES-3(B)/NMB-3(B).
FCC ID: 2AJXA-3N12021

PRECAUTIONS

  • FOR YOUR SAFETY, ALWAYS use a UL-listed Power Supply. Use of a non-UL-certified power supply may result in damage to your devices or cause other electrical problems including overheating and fire.
  • Medical Implants: Please maintain a minimum of 20 cm (8”) safe distance between the Wireless Charging Station (when powered ON) and any medical implants that can be affected by a magnetic field, such as pacemakers.
  • Do not immerse in liquid.
  • Do not place a magnet or any magnetically sensitive devices such as credit cards on the charging pad.
  • Avoid placing metal or magnetic objects near the Wireless Charging Station to prevent damage.

For accessories and product information visit
support.itechwearables.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals