Shenzhen Yiqizhao Technology A3 Wireless Charging Car Phone Holder User Manual

Shenzhen Yiqizhao Technology A3 Wireless Charging Car Phone Holder

Product Information

This equipment is subject to FCC radiation exposure regulations. To ensure compliance with these regulations, it must be installed and operated according to the provided instructions. The antenna(s) used with this transmitter must be installed in a way that maintains a separation distance of at least 20 cm from all persons. Additionally, the antenna(s) should not be placed in close proximity or operate together with any other antenna or transmitter. Both end- users and installers must be provided with antenna installation instructions and transmitter operating conditions to ensure compliance with RF (Radio Frequency) exposure guidelines.

Product Usage Instructions

1. Installation: Follow the provided instructions to correctly install the equipment.
2. Antenna Placement: Ensure that the antenna(s) used with this transmitter are positioned at least 20 cm away from any person. This separation distance helps maintain compliance with FCC radiation exposure regulations.
3. Avoid Co-location: Do not place the antenna(s) used with this transmitter in close proximity to any other antenna or transmitter. Operating multiple antennas or transmitters together can interfere with their performance and may result in non-compliance with regulations.
4. Antenna Installation Instructions: Both end-users and installers must be provided with detailed antenna installation instructions. These instructions should include information on how to properly install and position the antenna(s) to maintain the required separation distance.
5. Transmitter Operating Conditions: End-users and installers must also receive transmitter operating conditions. These conditions provide guidance on how to operate the transmitter in a manner that meets RF exposure guidelines.

It is important to adhere to these instructions and guidelines to ensure the safe and proper use of this product.

Parameter Specification

• input: DC 12V/1.5A,9V/1.67A/5V/2A
• output: 15W/10W/7.5W/5W
• Product standard: Qi
• Charging distance: < 8MM
• Product dimensions: 673867mm
• Product Material: ABS+Mag
  (QC2.0 is required for fast charging mode/QC3. 0 or 18W and above adapters)

Indicating status and protection functions

• Standby mode: LED light is always on. Press the touch area to switch 1 RGB mixed color + red, orange, yellow Green, green, blue and purple 7 colors.
• Charging mode: LED is off, remove the receiver and enter standby mode.
• Product size: 7130.571mm.
• FOD Automated Foreign Body Detection: Intelligent recognition of foreign bodies, such as hard objects, keys and other metal or magnetic objects
• All-round protection: temperature, short circuit, over-voltage over current.

Requirements

1. For models above IPHONE12, the magnetic car mount can be used directly in the state of bare metal without a shell. It can realize the function of magnetic fast charging and car bracket navigation [If you need to use it with a case, you need to be equipped with a magnetic mobile phone case with a built-in magnetic attracting sheet function]
2. Other brands of mobile phones with wireless charging function need to wear magnetic coils, use this magnetic bracket [All mobile phones with wireless charging function can realize magnetic fast charging + mobile phone bracket and navigation]
3. Wear a magnetic coil on a mobile phone without a wireless charging function, and use this magnetic car mount [All mobile phones without wireless charging function can realize magnetic suction bracket and car navigation]
4. When pasting the magnetic guide sheet, it should be stuck in the center of the mobile phone, please use the positioning sticker scale to measure [Measurement method of the positioning sticker: The size indications of the surrounding scales are the same. At this time, the center circle of the positioning sticker is the mobile phone. Center position]

Indication of product parts

Attention

1. Do not squeeze or collide heavily.
2. Do not disassemble or put into fire by yourself when the power is on, in water, to avoid short circuit leakage.
3. Do not use in severe high temperature, humidity or corrosive environments to avoid damaging the circuit Leakage occurred
4. Do not charge magnetic cards (ID cards, bank cards, etc.) with magnetic strips or chips On the board, avoid magnetic card failure.
5. Do not place metal (metal objects such as coins) on the charging plate while charging, as this will prevent Cause heat damage

• 5V2A adapter for normal mode charging (5W output)
• 9V1. 67A adapter for Apple mobile phone fast charging mode (7.5W output)
• 9V1. 67A for Samsung mobile phone fast charging mode (10W output)
• 12V1. 5A adapter for 15W power fast charge mode charging (15W output)
  Note: This product is applicable to all QI standard mobile phones with wireless charging functions. Other mobile phones need additional receivers.

FCC

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, usesr and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>