French Fitness FFB-PSLP FFB Black Pendulum Squat Leg Press Machine Instruction Manual

: June 13, 2024
: FRENCH FITNESS

Table of Contents

French Fitness FFB-PSLP FFB Black Pendulum Squat Leg Press Machine
FEATURES
TECH SPECS
WARRANTY
SAFETY INFORMATION
EXPLODED DIAGRAM PARTS LIST
ASSEMBLY INSTRUCTIONS. STEP 1
ASSEMBLY INSTRUCTIONS. STEP 2
ASSEMBLY INSTRUCTIONS. ST EP 3
ASSEMBLY INSTRUCTIONS. ST EP 4
ASSEMBLY INSTRUCTIONS. ST EP 5
ASSEMBLY INSTRUCTIONS. ST EP 6
ASSEMBLY INSTRUCTIONS. ST EP 7
ASSEMBLY INSTRUCTIONS. ST EP 8
ASSEMBLY INSTRUCTIONS. ST EP 9
Read User Manual Online (PDF format)
Download This Manual (PDF format)

French Fitness FFB-PSLP FFB Black Pendulum Squat Leg Press Machine

French Fitness FFB-PSLP FFB Black Pendulum Squat Leg Press
Machine

FEATURES

High quality heavy gauge steel frame
Adjustable non-slip foot plate
Adjustable height safety pin
Injected shoulder pads
Wide foot plate
California Residents see Prop 65 WARNINGS

TECH SPECS

Maximum User Weight: 220 lbs (100kgs)
Maximum Load Weight (Amount of Weight Plates): 330 lbs (150kgs)
Product Weight: 280 lbs (127kgs)
Dimensions: 73″L x 44″W x 64″H (L:185.7cm, W:112.3cm, H: 161.5cm)

WARRANTY

10 Years Parts, 1 Year Labor (Light Commercial)

SAFETY INFORMATION

Important– Please read fully before assembly or using

Please take sufficient time to read the installation instructions before assembling the unit.

Before beginning any exercise program, a general medical examination should be performed by a physician to rule out any health risks.
With improper use of the machine, such as excessive exercise, incorrect settings, etc., damage to health cannot be ruled out.

This machine is intended solely for use by adults and adolescents with appropriate physical and mental development.
Make sure that every user of this machine is sufficiently familiar with all of its functions. Learn the proper exercise technique before training with heavy weights.

Never allow children to play on this machine or in its immediate vicinity!

Worn or defective parts pose a safety risk and have to be replaced immediately! If there are defects in the machine it must not be used until it is fully repaired!

Use of this machine is only approved for the purpose it is intended for! The specified capacity limits must not be exceeded!

When setting up the machine allow for enough freedom of movement for its operation and for exercising .Special attention should be paid to its moving parts.
If it is fastened to the wall or ceiling, you must make sure there is enough load-bearing capacity at these fixture sites.

The machine must be set up on a horizontal, level, and stable surface! Any unevenness on the floor must be compensated for.

Place the exercise machine such that no one can hurt his or herself on protruding parts.
Weight plates and bars should be removed from the machine after training, and stowed away in the storage system provided.

EXPLODED DIAGRAM PARTS LIST

Note: Some of the smaller components may be pre-฀toted to larger components. Please check carefully before contacting us regarding any missing components.

Part	Description	O’ty
1	Plastic bumper	2
2	Bearing unit	2
3	3 Spring knob 2	2
4	4 Knob M10x20 1	1
5Washer฀10		2
6	Big washer฀10	7
7	Washer 12	96
8	Lock nut M12	49
9	Hex bolt M10x25	1
10	Hex bolt M10x70	3
11	Hex bolt M10x90	4
12	Hex bolt M12x20	6
13	Hex bolt M12x80	2
14	Hex bolt M12x100	31
15	Hex bolt M12x105	4
16	Hex bolt M12x115	4
17	Carriage bolt M12x70	2
18	Carriage bolt M12x100	6

ASSEMBLY INSTRUCTIONS. STEP 1

UNPACK THE CARTON AND PLACE ALL PARTS ON THE FLOOR. CAREFULLY REMOVE ALL PACKING MATERIAL AND CHECK EACH PART WITH THE MANUAL FIRST.
REMEMBER SOME PARTS ARE PRE-FITTED TO LARGER COMPONENTS.

IMPORTANT
ASSEMBLE WITH ALL NUTS AND BOLTS LOOSE AT FIRST, ONLY TIGHTEN AFTER COMPLETING ALL ASSEMBLY STEPS.

ASSEMBLY INSTRUCT IONS