EMERSON 535-2711 Termination Blocks Modbus Instruction Manual

: June 13, 2024
: Emerson

Table of Contents

EMERSON 535-2711 Termination Blocks Modbus
Product Information
Product Usage Instructions
Installation Instructions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EMERSON 535-2711 Termination Blocks Modbus

Product Information

The product in question is a termination block offered by Emerson. It is designed to be used with third-party devices that do not have termination capabilities or do not supply the required termination resistance. Emerson provides different termination blocks for terminating MODBUS network endpoints and Echelon network endpoints.

The following termination blocks are available:

Part Number	Description	Use For	Termination Resistance (Ohms)
535-2711	MODBUS Termination Block	Terminating MODBUS network endpoints	150

Product Usage Instructions

Consult the manufacturer’s instructions for termination information of third-party devices.
If the devices do not have termination capabilities or do not supply the required termination resistance, you can use Emerson termination blocks.
If you need to terminate MODBUS network endpoints, use the MODBUS Termination Block (P/N 535-2711). The required termination resistance for all E2, E3, or Site Supervisor RS485 networks is 150 ohms. Do not use 120-ohm termination even if it is supplied with the end-of-line device.
If you need to terminate Echelon network endpoints, use the Echelon Termination Block (P/N 535-2715). The required termination resistance is 105 ohms.
Connect the termination block to the end device on the daisy chain using a network cable with a length of six inches or less (refer to Figure 2).
Optionally, if recommended, connect the shield wire to earth’s ground. Keep the exposed shield wire length as short as possible, with a maximum length of three inches.

Please note that the product documentation is subject to change, and for the latest technical documentation and updates, it is recommended to visit Emerson’s website at www.climate.emerson.com.

Installation Instructions

Third-party devices may or may not have onboard termination jumpers (consult the manufacturer’s instructions for termination information). For devices that have no termination capabilities or do not supply the required termination resistance, Emerson offers termination blocks that can be used.
To terminate MODBUS network endpoints, use P/N 535-2711; 150-ohm termination is required for all E2, E3 or Site Supervisor RS485 networks (do not use 120-ohm termination even if supplied with the end-of-line device). To terminate Echelon network endpoints, use P/N 535-2715.
Wire the termination block across the RS485 + and RS485 – terminals of the end device on the daisy chain.
Connect the block to the end device on the daisy chain using six inches or less of wire from the network cable used for the daisy chain (Figure 2), and optionally if recommended, connect the shield wire to earth ground, keeping the exposed shield wire length as short as possible (three inches ideal maximum length).

Part Number	Description	Use For	Ohms

535- 2711

| MODBUS

Termination Block

| MODBUS

Termination Resistance

| 150

ohms

535- 2715

| Echelon Termination Block| Echelon Termination Resistance| 105

ohms

535- 2710| OBSOLETE| | 52.5

ohms

Table 1 – Emerson Termination Blocks

Document Part # 026-4830 Rev 1

This document may be photocopied for personal use.

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

Join Emerson Technical Support on Facebook. http://on.fb.me/WUQRnt

For Technical Support call 833-409-7505 or email ColdChain.TechnicalServices@Emerson.com

The contents of this publication are presented for informational purposes only and they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. Emerson reserves the right to modify the designs or specifications of such products at any time without notice. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end-user.