MATRIX E50XIR Elliptical Trainer User Manual
- June 13, 2024
- MATRIX
Table of Contents
E30/ E50
ASSEMBLY
WARNING!
There are several areas during the assembly process that special attention
must be paid. It is very important to follow the assembly instructions
correctly and to make sure all parts are firmly tightened. If the assembly
instructions are not followed correctly, the equipment could have parts that
are not tightened and will seem loose and may cause irritating noises. To
prevent damage to the equipment, the assembly instructions must be reviewed
and corrective actions should be taken.
UNPACKING
Unpack the equipment where you will be using it. Place the carton on a level
flat surface. Never open box when it is on its side.
IMPORTANT NOTES
During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded.
Several parts have been pre-lubricated to aid in assembly and usage. Please do
not wipe this off. If you have difficulty, a light application of lithium
grease is recommended.
SERIAL NUMBER LOCATION
Before proceeding, find your elliptical’s serial number located on a barcode
sticker and enter it in the space provided below.
SERIAL NUMBER
MODEL NAME
F E30
F E50 MATRIX ELLIPTICAL
TOOLS INCLUDED:
- 5 mm Allen Wrench
- 6 mm Allen Wrench
- 13/17 mm Flat Wrench
- Phillips Screwdriver
PARTS INCLUDED:
- 1 Elliptical Frame
- 1 Console Mast
- 1 Console Mast Boot
- 2 Handlebars
- 2 Handlebar Caps
- 2 Pedals with Inserts
- 2 Transport Handles
- 1 Power Cord
- 1 Hardware Kit
NEED HELP?
If you have questions or if there are any missing parts, contact Customer Tech
Support. Contact information is located on the information card.
- Use the information above when calling for service.
A Open HARDWARE FOR STEP 1.
B Remove 4 PRE-INSTALLED SCREWS (5) and TOP CAP COVER (6)from MAIN FRAME (4).
C Carefully pull the CABLE (1) through the CONSOLE MAST (2) using the LEAD
WIRE
(3) located inside the CONSOLE MAST (2).
D Attach CONSOLE MAST (2) to MAIN FRAME (4) using 4 BOLTS (A) and 4 FLAT
WASHERS (B). Tighten to 40 Nm / 29 lb-ft.
E Attach the TOP CAP COVER (6) to the MAIN FRAME (4) using 4 PRE-INSTALLED
SCREWS (5).
F Attach the CONSOLE MAST BOOT (7) to the TOP CAP COVER (6) by snapping it
into place.
Hardware For Step 1
| Description| Qty
---|---|---
A| Bolt| 4
B| Flat Washer| 4
Note: Be careful not to pinch any wires while attaching the upper assembly.
A Open HARDWARE FOR STEP 2.
B Slide LOWER DUAL ACTION ARM (8) onto the CONSOLE MAST (2)
C Attach using 1 FLAT WASHER (E), 1 HANDLEBAR CAP (9), 1 FLAT WASHER (F), 1
SPRING WASHER (G) and 1 BOLT (H). Tighten to 40 Nm / 29 lb-ft.
D Repeat on other side.
Hardware For Step 3
| Description| Qty
---|---|---
E| Flat Washer (25 mm)| 2
F| Flat Washer (19 mm)| 2
G| Spring Washer| 2
H| Bolt| 2
A Open HARDWARE FOR STEP 3.
B Attach the LINK ARM (9) to the HANDLEBAR (8) using 1 BOLT (I). 1 NUT (J).
C Repeat on other side.
Hardware For Step 3
| Description| Qty
---|---|---
I| Bolt| 2
J| Nut| 2
A Open HARDWARE FOR STEP 4.
B Connect the CABLES (1) to the CONSOLE (13) and carefully tuck the excess
cable into the CONSOLE MAST (2).
C Attach the CONSOLE (13) to the CONSOLE MAST (2) using 4 BOLTS (K).
D Attach PEDAL (14) to LINK ARM (9) using 4 SCREWS (L). Repeat on other side.*
Hardware For Step 4
| Description| Qty
---|---|---
K| Bolt| 4
L| Screw| 8
Note: Be careful not to pinch any wires while attaching the console.
ASSEMBLY COMPLETE!
A To relocate elliptical, install TRANSPORT HANDLES as shown.
B Remove TRANSPORT HANDLES before using elliptical.
© 2020 Johnson Health Tech
Rev 1.0 B
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>