UltraRay PX1302 UV-C Bulb Instructions
- June 13, 2024
- UltraRay
Table of Contents
UltraRay PX1302 UV-C Bulb
Product Information:
- Product Name: UltraRayTM UV-C Bulb – Annual Replacement
- Model: PX1302
- Manufacturer: SpaDepot.com
Product Usage Instructions
- Turn off the circuit breaker to the spa and allow the UV-C bulb to cool.
- Using a Phillips screwdriver, remove the Water Hose Barb Clamp 1 and Bulb Boot Clamp 2 as shown in Fig. A.
- Lift the white Quartz Chamber 4 slightly out of its cradle to facilitate the next steps.
- Refer to Fig. B and disconnect the old UV-C Bulb 5 by gently pulling on the Bulb Plug Boot 3.
- Slide the old UV-C Bulb 5 out of the Quartz Chamber 4 and set it aside. Note: the original bulb may have come with a black rubber end cap for shipping protection, which is not needed for the new bulb.
- Remove the new UV-C Bulb 5 from its packaging, being careful not to touch the glass portion with bare hands to avoid shortening bulb life. Slide the bulb most of the way into Quartz Housing 4 with pins facing outward.
- While firmly grasping the white bulb end 5 with two fingers, reconnect the Bulb Plug Boot 3, ensuring that the bulb pins align and seat into the boot socket by rotating the bulb slightly if needed.
- Push the Bulb Plug Boot 3 securely into the Quartz Chamber 4.
- Reach the Water Hose Barb Clamp 1 and Bulb Boot Clamp 2 with a screwdriver as shown in Fig. A.
- Turn on the circuit breaker to restore spa power.
- Hold down the Reset Button 6 and both LED lights will flash yellow. Continue to hold for about 10 seconds until both lights turn green.
BULB DISPOSAL WARNING: The UV bulb contains mercury. Dispose of the bulb
in accordance with all laws. Visit
www.LampRecycle.org for disposal information.
Address: ASO 605 S. Williams Rd. Palm Springs,CA 92264
DESCRIPTION
| ITEM | DESCRIPTION |
|---|---|
| 1 | Water Hose Barb Clamp |
| 2 | Bulb Boot Clamp |
| 3 | Bulb Plug Boot |
| 4 | Quartz Chamber |
| 5 | UV‐C Bulb |
| 6 | Reset Button |
DANGER: TURN THE SPA CIRCUIT BREAKER TO THE OFF POSITION!
WARNING: ALLOW BULB TO COOL DOWN PRIOR TO REMOVING FROM QUARTZ CHAMBER.
DANGER: NEVER LOOK AT THE LIT BULB. THIS CAN CAUSE SEVERE EYE DAMAGE OR BLINDNESS.
ASSEMBLY
-
Turn off circuit breaker to spa and allow UV‐C bulb to cool.
-
[Refer to Fig. A] Using a Phillips screwdriver, remove Water Hose Barb Clamp 1 and Bulb Boot Clamp 2.
-
Lift the white Quartz Chamber 4 slightly out of its cradle to facilitate the next steps.
-
[Refer to Fig. B] Disconnect the old UV‐C Bulb 5 by gently pulling on the Bulb Plug Boot 3.
-
Slide the old UVC‐Bulb 5 out of the Quartz Chamber 4 and set aside.*
Note: the original bulb may have come with a black rubber end cap for shipping protection. It is not needed for the new bulb. -
Remove the new UV‐C Bulb 5 from its packaging, being careful not to touch the glass portion with bare hands. (Oil from your skin can cause a “hot spot” on the glass, shortening bulb life). Slide bulb most of the way into Quartz Housing 4 with pins facing outward.
-
While firmly grasping the white bulb end 5 with two fingers, reconnect the Bulb Plug Boot 3, being careful to align and seat the bulb pins into the boot socket by rotating bulb slightly as needed.
-
Push Bulb Plug Boot 3 securely into Quartz Chamber 4.
-
[Refer to Fig. A] Reattach the Water Hose Barb Clamp 1 and Bulb Boot Clamp 2 with screwdriver.
-
Turn on circuit breaker to restore spa power.
-
Hold down Reset Button 6 and both LED lights will flash yellow. Continue to hold for about 10 seconds until both lights turn green.
BULB DISPOSAL
WARNING: The UV bulb contains mercury. Dispose of bulb in accordance with all laws. Visit www.LampRecycle.org for disposal information.
ASO
605 S. Williams Rd.
Palm Springs, CA 92264
References
- SpaDepot.com | America's Favorite Hot Tub Supply Store
- Lamp Recycle – Environmental Responsiblility Starts Here
- SpaDepot.com | America's Favorite Hot Tub Supply Store
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>