artika VAN-SWR-BL Swirl LED Vanity Light Instruction Manual

artika VAN-SWR-BL Swirl LED Vanity Light

Product Information

The LED Vanity Light – SwirlTM is a wall-mounted light fixture designed for indoor use in residential settings. It is manufactured in China and distributed by a company located at 2455 Paces Ferry Rd., NW Atlanta, GA 30339. The product comes with included hardware, including wire connectors, canopy screws, mounting bracket, and canopy. It is important to note that this product is intended for residential use only and should be used indoors.

Product Usage Instructions

Before installing and using the LED Vanity Light – SwirlTM, please read and follow these instructions carefully:

1. Ensure that the breaker at the panel is turned off before starting the installation process.
2. Place the light fixture over the junction box and use a level to verify its position. Mark two reference points on the wall at the end of the light fixture where it will be installed.
3. Attach the mounting bracket to the junction box using the provided screws. Make sure that the screws are pointing away from the junction box.
4. Attach the hook to the mounting bracket.
5. Connect the white wire (N) from the light fixture to the white supply wire (N) from the junction box using a wire connector. Connect the black wire (L) from the light fixture to the black supply wire (L) from the junction box using a wire connector. Connect the ground wire (G) from the light fixture to the ground supply wire (G) from the junction box using a wire connector.
   It is important to note that if you plan to use a dimmer with this product, make sure it is LED compatible to avoid any issues. Additionally, it is recommended to have this product installed by a certified electrician to ensure proper installation and compliance with local electrical and building codes.
   For any further assistance or inquiries, you can contact the manufacturer’s helpline at 1-877-527-0313 or visit their website at www.homedepot.com.

INCLUDED HARDWARE

WHAT YOU WILL NEED

CAUTION
If using a dimmer, it must be LED compatible.

IMPORTANT

• The installer and/or user must read, understand and follow these instructions before installing the product. This product must be properly installed before it is used. If instructions are not followed, the manufacturer will not be held responsible for any problems or product malfunction. Failure to follow installation and/or operating instructions voids the warranty.
• We recommend that this product be installed by a certified electrician. In some states or provinces, it is a legal requirement for this type of product to be installed by a certified electrician, according to the electrical and building codes effective in the region where the unit is used.
• This product is compatible with most LED dimmers.
• WARNING:
  • Risk of electrical shock.
  • Turn off breaker at the panel.
• Switch off the main electrical supply from the fuse box/circuit breaker before installing the unit or doing any maintenance.
• Do not use outdoor.

STEP-BY-STEP INSTALLATION

1. Turn off breaker at the panel.
2. Place the light fixture over the junction box and verify the position with the level. Mark on the wall two reference points at the end of the light fixture where it will be installed.
3. Attach the mounting bracket to the junction box fastening with the junction box screws.
4. Ensure the screws attached to the mounting bracket are pointing away from the junction box (fig. 1)

5. Attach the hook to the mounting bracket (fig. 2).
6. Connect the white wire (N) from the light fixture to the white supply wire (N) from the junction box using a wire connector. Connect the black (L) wire from the light fixture to the black supply wire (L) from the junction box using a wire connector. Connect the ground wire (G) from the light fixture to the ground supply wire (G) from the junction box using a wire connector (fig. 2)

7. Push the wires into the junction box. Mount the light fixture onto the mounting bracket and secure it with the support screws (fig. 3).
8. Restore electrical power.

WARNING:

• Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
  1. This device may not cause harmful interference, and
  2. this device must accept any interference received,including interference that may cause undesired operation.
• NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help

WARRANTY

• Artika For Living Inc. is proud to offer you a five-year (5) limited warranty on manufacturing defects from the date of purchase for residential use only. The warranty is extended to the original owner in US, Canada, Mexico, the UK, Iceland, France and Spain and is non-transferable. It does not apply to retailers, commercial applications or establishments. The original sales receipt is required for all warranty claims. The remedy under this limited warranty shall be product or part replacement at Artika’s discretion as provided herein and may not exceed the original purchase price.
• This warranty is valid only on products installed in accordance with the building code and laws in effect in the region where the unit is being used, as well as in accordance with the provided instruction manual. It does not cover products installed incorrectly or subjected to abnormal use. You may be required to return product(s) or component part(s) for inspection and verification.
• Normal wear and tear, misuse, negligence, vandalism, improper maintenance (surface damage due to chemical interaction or cleaning agents including, but not limited to, scouring pads, use of cleaners containing abrasives, alcohol or other organic solvents) improper handling, accident, abuse, fire, flood, theft, acts of God, neglect, or alteration of the product will not be covered under this limited warranty. It excludes any accessories that accompany the product including, but not limited to bulbs or batteries.
• This warranty does not cover handling, labour, transportation, or any other cost associated with the installation or replacement of the product. This limited warranty is valid in the country of purchase and for products sold by Artika authorized retailers only.
• Artika for Living Inc. will not be held
  responsible for any direct or consequential damages or injuries related to the use of this product arising from improper use or installation of this product.
  Please visit www.artika.com to discover more about Artika for Living Inc.

ABOUT COMPANY

• Artika For Living Inc.
• 1756, 50th Avenue
• Montréal (Lachine), Québec,
• Canada H8T 2V5
• 1-866-661-9606
• support@artika.com
• www.artika.com
• Customer Service
  Monday to Friday 9 a.m. – 5 p.m. EST

References

• Modern Lighting Fixtures | Best Online Lighting Store | Artika

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>