TRAXXAS trx1039 ECM-2.5 Electronic Control Module User Guide

QUICK START GUIDE

Turning on Your Model

1. Tum on the transmitter.
   Always turn the transmitter on first, before tuming on the model. The transmittersLED will glow green.

2. Turn on the model by plugging the battery into the electronic control module.
   Plug the battery into the EQM. Make sure the battery plug is completely inserted. The LED will glow green.

To turn the model off:
Unplug the battery from the ECM. The battery should always be unplugged from the ECM when the vehicle is not in use. For this reason, ‘the model is not equipped with a traditional on/off switch. Turn off the transmitter.

Operating Your Model

For maximum radio range, hold the transmitter upright and pointed in the direction of the model.
Reversing: After stopping the model, return the transmitter’s trigger to neutral and push up again to activate reverse throttle.

Transmitter Adjustments

Steering Trim
To adjust, drive the vehicle forward slowly while“steering”with the trim knob until the vehicle travels in a straight line with no steering input.

Low Voltage Detection

The ECM is equipped with three-stage Low Voltage Detection (LVD) that alerts the driver when LiPo batteries have reached their minimum voltage (discharge) threshold. Stopimmediately to prevent the battery pack from being discharged belowits safe minimum threshold. Unplug the battery and recharge. Leaving the battery connected to the vehicle when not is use can cause permanent battery damage. Always unplug the battery after use.

and recharge
2| Fast
blinking red| On| On| viefticle w ill not dine| Unplug the battery and recharge
3| Off| Off| Off| Stage 3 shutdown| Lhplog the battery
and recharge

Drive Node Profiles

The ECM is equipped with three driving profiles.

Sport Mode (Single red flash)
Allows full forward, reverse, and braking power.
Trail Mode (Two red flashes)
Default factory setting. Adds drag brake at neutral to Sport Mode to slow descent down hills.

Crawl Mode (Three red flashes)
Increases Trail Mode drag brake at neutral to 100% for maximum hill hold.

To change drive modes:

1. With the ECM powered on, press and hold the EZ-Set button.
2. The EZ-Set button will flash red once, then twice, then three times.
3.  Release the EZ-Set button after the desired number of flashes to select the mode.

Pro Scale® Lighting
Your new Traxxas model is enabled with Pro Scale• lighting features, such as headlights, reverse lights, and brake lights. Visit Traxicas.c.om to learn more about these features and available Traxxas Pro Scale Lighting Kits, parts, and accessories.
Running in Wet Conditions
The electronic components are waterproof to a lbw driving in wet conditions. After running, thoroughly dean and dry the model and lubricate/protect metal part and hardware as needed to present rust and corrosion.

FCC Compliance
This device contains a module that complies with the limits for a Class 8 digital device as described In part 15 of the FCC rules. Operation is subject to the following two conditions (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including Interference that may cause undesired operation. The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The limits for a Class El digital device are designed to provide reasonable protection against harmful Interference in residential settings. This product generates, uses and can radiate radio frequency energy, and. If not operated In accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be detemined by turning the equipment off and on, the user Is encouraged to try to correct the interference by one or morel the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Canada, Industry Canada (IC)

This Class 8 digital apparatus complies with Canadian ICES-003 and RSS-210. This device complies with Industry Canada license exempt RSS standard (s). Operation is subject to the following two conditions This device may not cause interference, and This device must accept any interference, including interference that may cause undesired operation of the device. Radio Frequency (RF) Exposure Statement This equipment complies with radio frequency exposure limits set forth by FCC and Industry Canada for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or bystanders and must not be co-located or operating in conjunction with any other antenna or transmitter.
Traxxas 6250 Traxxas Way McKinney, Texas 75070 Phone: 972-549-3000 Toll-free 1-888-TRAXXAS
Internet Traxxas.com E-mail: support@Traxxas.com
Entire contents (.;-2022 Traxxas. All rights reserved. Traxxas, Ready-To- Drive, TQ, Titan, TRX-4M, and ECM-2.5 are trademarks or registered trademarks of Traxxas. Other brand names and marks are the property of their respective holders and are used only for purposes of identification. No part of this manual may be reproduced or distributed in print or electronic media without the express written permission of Traxxas. Specifications are subject to change without notice.

Official Licensed Product
Ford Motor Company Trademarks and Trade Dress used under license to Traxxas.
Ford, and Rroncov are trademarks of Ford Motor Company. All copyrights and trademarks are used by Traxxas under license.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>