JWIPC i7-L7-11 OneScreen OPS PC Module User Guide
- June 13, 2024
- JWIPC
Table of Contents
JWIPC i7-L7-11 OneScreen OPS PC Module User Guide
1.Package Checklist
Thank you for choosing our products.
- Please check whether the package is complete, if there is any damage or shortage of accessories, please contact your agency as soon as possible
- OPS x 1
- Wifi antenna x 2 (optional)
- Simple User guide x 1
- ATN Screw x 2 (optional)
2.Product Configuration
3.IO Interface
- POWER BUTTON: Power Switch Button
- ANT: WIFI antenna
- MIC-IN : Plug for microphone
- LINE-OUT: Audio jack
- LED:(top) hard disk indicator, (bottom) power indicator
- TYPEC: TYPE C port
- HDMI: High definition multimedia display interface
- USB3.1: USB3.1 port
- LAN: RJ-45 network interface
- USB2.0: USB2.0 port
- RESET: Reset button
- SIM card: SIM Card Slot
- JAE 80PIN: 80 pin extension port
- DC IN: DC power interface
Declaration of RoHS2.0 Compliance
S084 has been designed and manufactured in compliance with Directive (EU)
2015/863 of the European Parliament and the Council on restriction of the use
of certain hazardous substances in electrical and electronic equipment
(RoHS2.0 Directive) and is deemed to comply with the maximum concentration
values issued by the European Technical Adaptation Committee (TAC) as shown
below:
**Certain components of products as stated above are exempted under the Annex III of the RoHS2 Directives as noted below: Examples of exempted components are:
- Lead in glass of cathode ray tubes.
- Lead in glass of fluorescent tubes not exceeding 0.2% by weight.
- Lead as an alloying element in aluminium containing up to 0.4% lead by weight.
- Copper alloy containing up to 4% lead by weight.
- Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).
- Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezo electronic devices, or in a glass or ceramic matrix compound.
Declaration of RoHS2.0 Compliance
S084 has been designed and manufactured in compliance with Directive (EU)
2015/863 of the European Parliament and the Council on restriction of the use
of certain hazardous substances in electrical and electronic equipment
(RoHS2.0 Directive) and is deemed to comply with the maximum concentration
values issued by the European Technical Adaptation Committee (TAC) as shown
below:
**Certain components of products as stated above are exempted under the Annex III of the RoHS2 Directives as noted below: Examples of exempted components are:
- Lead in glass of cathode ray tubes.
- Lead in glass of fluorescent tubes not exceeding 0.2% by weight.
- Lead as an alloying element in aluminium containing up to 0.4% lead by weight.
- Copper alloy containing up to 4% lead by weight.
- Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).
- Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezo electronic devices, or in a glass or ceramic matrix compound.
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any inte rference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>