BOMANN KB 7346 ix Look Refrigerator User Guide

BOMANN KB 7346 ix Look Refrigerator

Introduction

Thank you for choosing our product. We hope you will enjoy using the appliance.

Symbols in these instructions for use
Important information for your safety is specially marked. It is essential to comply with these instructions to avoid accidents and prevent damage.

WARNING: This warns you of dangers to your health and indicates possible injury risks.
CAUTION: This refers to possible hazards to the machine or other objects.

NOTE: This highlights tips and information.

General notes
Read the operating instructions very carefully before putting the appliance into operation and keep the instructions including the warranty and the receipt. If you give this appliance to other people, also pass on the operating instructions.

NOTE:

• Due to constant product modifications, your appliance may differ slightly from these operating instructions; Functions and methods of use remain unchanged.
• The illustrations in these operating instructions may differ from the original appliance.
• The appliance is designed exclusively for private use and for the envisaged purpose. This appliance is not fit for commercial use.
• The appliance is only to be used as described in the user manual. Do not use the appliance for any other purpose. Any other use is not intended and can result in damages or personal injuries.
• This appliance is not intended to be used as a built-in appliance.
• Do not use it outdoors. Keep it away from sources of heat, direct sunlight and humidity.
• When not in use, for cleaning, user maintenance works or with disruption, switch off the appliance and disconnect the plug (pull the plug itself, not the lead) or turn off the fuse.
• The appliance and if possible the mains lead have to be checked regularly for signs of damage. If damage is found the appliance must not be used.
• For safety reasons, alterations or modifications of the appliance are prohibited.
• To ensure your children’s safety, please keep all packaging (plastic bags, boxes, polystyrene etc.) out of their reach.
• WARNING: Do not allow small children to play with the foil. There is a danger of suffocation!

Special safety information for this unit

• This unit is intended to be used in household and similar applications such as
  • staff kitchen areas in shops, offices and other working environments;
  • farmhouses and by clients in hotels, motels and other residential-type environments;
  • bed and breakfast type environments;
  • catering and similar non-retail applications.

WARNING:

• Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.
• Do not use mechanical devices or other means to accelerate the defrosting process (if necessary), except those described in this manual (depending on the model included the scope of delivery).
• Do not damage the refrigerant circuit.
• Do not operate any electrical devices inside the appliance.
• Do not store explosive substances such as aerosol containers with flammable propellant in the appliance.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children unless they are older 8 years and supervised.
• NOTE: Children aged from 3 to 8 years are allowed to load and unload refrigerating appliances.
• When positioning the appliance, ensure the supply cord is not trapped or damaged.
• Do not locate multiple portable socket outlets or portable power supplies at the rear of the appliance.
• Do not try to repair the appliance on your own. Always contact an authorized technician. To avoid exposure to danger, always have faulty cable be replaced only by the manufacturer, by our customer service or by qualified person and with a cable of the same type.
• Use the provided collection points of electrical equipment for the disposal of the appliance.

Coolant
WARNING: Risk of fire / flammable materials
The coolant circuit of this unit contains the refrigerant Isobutane (R600a), a natural gas that is flammable and of high environmental compatibility. Make sure no parts of the coolant circuit get damaged during transport and installation of the appliance.

If the coolant circuit is damaged:

• avoid any open flames or ignition source,
• disconnect the plug,
• thoroughly air the room in which the appliance is installed and
• contact an authorized technician.

Transport and packaging

Transport the appliance
Transport the appliance, if possible, in vertical position. Otherwise, it is absolutely necessary to allow the appliance standing upright for a few hours before installation ”Prior to first use”. Protect the appliance during transport against weather influences.

Unpacking the appliance

• Remove the appliance from its packaging.

• Remove all packaging material, such as foils, filler and cardboard packaging.
  Dispose of packaging materials that are no longer required in accordance with the locally applicable regulations.

• To prevent hazards, check the appliance for any transport damage.

• In case of damage, do not put the appliance into operation. Contact your distributor.

NOTE: Production residue or dust may have collected on the appliance. We recommend cleaning the appliance according to chapter “Cleaning and maintenance”.

Appliance equipment

• Appliance overview

1. Grid shelves
2. Temperature control
3. Door storage with brackets
4. Feet

• Delivery scope
  2x grid shelf, 2x door storage bracket

Installation

Conditions for the installation location

• Good ventilation is required around the appliance to dissipate the heat properly and to guarantee efficient cooling operation at low power consumption. Enough clearance is necessary.

  • Gap to the back approx. 50～70 mm, to the side walls and above the appliance each approx. min. 100 mm;
  • Place the appliance so that the appliance door can open without being impeded.

• Only install at a location with an ambient temperature suitable for the climate class of the appliance.
  The climate class can be found under “Technical data” and on the rating label located in the interior or on the appliance rear.

• Place the appliance on a steady and safe surface. If the appliance is not horizontally leveled, adjust the feet accordingly.

• Avoid the installation:

  • near heaters, next to a stove, direct sunlight or any other heat sources;
  • at locations with high humidity (e.g. outdoors, bathroom), as metal parts would be susceptible to corrosion under such circumstances;
  • near volatile or flammable materials (e.g. gas, fuel, alcohol, paint, etc.), in rooms that may have poor air circulation (e.g. garages).
  • Do not expose the appliance any weather.

Leveling the appliance
Slight unevenness in the floor can be leveled out using the front feet. Check whether the appliance is leveled horizontally. If the appliance is not in balance, the feet must be adjusted.

Electrical connection

WARNING:

• The installation to the mains supply must conform to the local standards and regulations.
• Improper connection may cause to an electric shock!
• Do not modify the appliance plug. If the plug does not fit properly to the outlet, let install a proper outlet by an authorized specialist.
• The accessibility of the power plug must be ensured to disconnect the appliance from the power supply in case of emergency.
• Make sure that the voltage supply matches the specifications on the rating label before connecting.
• Connect the mains cable to a properly installed and earthed wall outlet.
• If the plug after installation is not accessible, a corresponding disconnect device must be available to meet the relevant safety regulations.

Reversing the door opening

If required, the door opening can be moved from the right (supplied condition) to the left side.
WARNING: When replacing the door stop, the appliance must be disconnected from the power supply first.
NOTE: You possibly need: screw wrench, Phillips screwdriver as well as a thin-blade screwdriver.

• Remove the blind cap (1) and the hinge cover (2).
• Loosen the screws (3), remove the door hinge (4) and lift the appliance door.
• Move the blind plug (5) of the appliance door to the opposite side. Set the door aside safely.
• Tilt the appliance slightly backward and block it in this position. Dismount the door hinge (6) with its base by loosening the screws (7). Unscrew the separate foot (8).
• Move and fasten the door hinge (6) incl. base with the screws (7). Screw in the separate foot (8) accordingly.
• Put the appliance back in the upright position. Put on the appliance door and fix it in the intended position. Move and fasten the door hinge (4) with the screws (3).
• Replace the hinge cover (2) and move the blind cap (1) into the exposed hole.
  Check that the door is optimally aligned both vertically and horizontally to ensure a smooth opening and closing of the door.

Startup / Operation

Intended use
The appliance is intended for private/household use. It is suitable for cooling perishable foods such as milk, dairy products, meat, fish, eggs, margarine, various spreads and fruit and vegetables that are not sensitive to cold. This cooling box is not suitable for freezing food!

Prior to first use

CAUTION: After transport, the appliance should be left standing upright for four hours before connecting to the power supply. Nonobservance could lead to a malfunction of the cooling system and causes an appliance breakdown.
Clean the appliance interior including all accessory parts. Consider the instructions which we provide in the chapter “Cleaning and Maintenance”.

Starting the appliance

• Connect the appliance to the power supply.
• Set the operating conditions. See also the following sections.

Settings
Position [ OFF ] means that the appliance is in the switched-off state. Turn the temperature control clockwise from this position, the appliance switches on automatically. The power levels control the different values of the internal temperature.

Power level

MID| lowest level, warmest internal temperature
NORMAL| medium level, optimal operating temperature
**MAX***| highest level, coldest internal temperature

• Beware of high setting because the maximum level may already mean “freezing point”.

• Basically, the temperature changes depending on the ambient temperature (place of installation), the frequency of opening the door and the equipment.
  For initial operation, first set the lowest possible internal temperature (= highest power level) until the appliance has reached the desired operating temperature. It is recommended to reset to a medium power level afterwards, then you can easily make any temperature correction.

• Recommendation, for optimized food storage and to avoid food waste, a medium power level is generally best. A high power level also increases energy consumption.
  The recommended temperature in the center of the appliance is approx. 4∼7 degrees. If the temperature in the center is correct, the different zones usually also have the correct temperature.

• Equipment
  Note that the equipment varies depending on the appliance type.
  The various shelves and drawers can be removed for individual storage. Practical also for cleaning purposes.

NOTE: For the most efficient use of energy, place all shelves/drawers in their original positions.

Removing/inserting the shelves

• To remove, open the unit door completely, lift the shelf, if necessary, slant slightly and pull it out to the front.
• Safely reinsert the shelf and push it in until the stop is reached.

Removing/inserting the door storage bracket

• To remove, carefully release the bracket upwards from the retainer.
• Place the bracket flat, press down on both sides of the bracket so that it engages in the retainers.

Storing food

NOTE: Recommendation!
To guarantee that the temperature is low enough, you should pre-cool the appliance a few times before initial loading foods.
CAUTION: Always pay attention to the storage instructions on the sales packaging.

Always store food covered or packed to prevent dry-ing-out and transfer of odor or taste onto other food items. You may pack the food with e.g.

• Polyethylene plastic bags or foil
• Plastic bowl with lid
• Special plastic cover with elastic strip
• Aluminum foil

To avoid contamination of food, respect the following instructions:

• Opening the door for long periods can cause a significant increase of the temperature in the compartments of the appliance.
• Clean regularly surfaces that can come in contact with food and accessible drainage systems (see “Cleaning and maintenance”).
• Store raw meat and fish in suitable containers in the refrigerator, so that it is not in contact with or drip onto other food.
• Two-star frozen-food compartments are suitable for storing pre-frozen food, storing or making ice cream and making ice cubes.
• One- , two- or three-star compartments are not suitable for the freezing of fresh food.
• If the appliance is out of use for long period, follow the instructions under “Switching off”.

Temperature zones and storage recommendations
The optimal cooling temperature is around 4∼7 degrees for the central area of the cooling. Different cooling zones are created by the air circulation. Regardless of the power level, cold air drops off.

• The coldest zone is on the cooling rear wall and in the lower cooling part. Recommended for storing perishable foods such as meat, fish and sausages at around 2∼3 degrees.
• About that it becomes less cold. For dairy products such as yoghurt, cheese and co., the center of the cooling is just the right temperature at around 4∼7 degrees.
• Well-packed leftovers or preserves needs less cooling. The upper cooling part at around 6∼8 degrees could be the right place.
• The cooling door is one of the warmest locations. The upper racks are good location for food that needs moderate cooling, such as butter and eggs. There is space for drinks in the lower door racks.
• The vegetable drawer (depending on model) is suitable for fruit and vegetables at a temperature of around 8 degrees, depending on the cooling temperature. To make especially delicate fruits and vegetables feel comfortable, a glass shelf above the drawer retains the falling cold and prevents moisture loss.

Operating noise

Switching off

• To switch off the appliance turn the temperature control to the off state.
  If the appliance is out of use for long periods:

  • Remove the appliance content.
  • Disconnect the appliance from the power supply.
  • Defrost (model dependent) and clean the appliance thoroughly (see ”Cleaning and maintenance”).
  • Leave open the appliance door to avoid formation of mold and unpleasant odors.

• Tips for energy saving

  • Disconnect the appliance from the power supply if it isn’t in use.
  • Do not install the appliance near stoves, heaters or other heat sources. In case of higher ambient temperatures, the compressor will run more fre-quently and longer.
  • Ensure enough ventilation at the bottom and rear side. Never block ventilation openings.
  • Place all shelves, racks or drawers (depending on model) in their original position.
  • Adjust the temperature not colder than necessary.
  • Allow warm food to cool before placing it in the appliance.
  • Open the appliance door only as necessary.
  • Defrost the unit regularly (model dependent).
  • The seal of the appliance door must be completely intact, so that the door closes properly.

Cleaning and maintenance

WARNING:

• Always disconnect the appliance from the power supply before cleaning and user maintenance.
• Do not use steam cleaners for cleaning the appliance; moisture could enter electrical components. Risk of electric shock! Hot steam could damage the plastic parts.
• The unit must be dry before restarting operation.

CAUTION:

• Do not use a wire brush or other sharp, abrasive items.
• Do not use any acidic or abrasive detergents.
• Do not damage the refrigerant circuit.

Cleaning the appliance including interior
To keep dirt and germs at bay, clean the appliance regularly!

• First clear out the contents of the appliance and store it in a cool place. Remove all moving parts such as shelves and drawers.
• Clean the interior of the appliance, the exterior surfaces and the accessories with lukewarm water and a mild cleaning agent; or with a clean, damp microfiber cloth without cleaning agent.
• Clean the thaw water discharge channel/opening carefully e.g. with a pipe cleaner.
• After everything has dried thoroughly, you can put the appliance back into operation.
• Depending on the model: At least once a year, wipe off the dust that has accumulated on the rear wall of the unit and on the condenser (metal grille). Use a soft brush or a vacuum cleaner for this purpose.

Cleaning / replacing the door seal
Regularly check the seal for dirt, damage and air tightness!

Checking the seal for air tightness

• Clamp a thin piece of paper at various points for testing. The paper must be equally difficult to pull through at all points.

Cleaning the gasket

• Clean the gasket with clear water only!
• CAUTION , grease and oil makes the seal porous and brittle. Wipe up grease or oil immediately with a damp, clean cloth.

Replacing the seal

• Remove the contents of the appliance and, if necessary, defrost the unit. Pay attention to how the old gasket is attached. Most gaskets are only plugged in.
• Remove the worn gasket rubber by removing it from the groove. Carefully clean the appliance door and the groove below the rubber and remove any adhesive residue.
• Attach the new rubber. If necessary, heat the rubber seal with a hair dryer or hot water and shape it by hand. Start pressing the gasket in one corner and then press it around the door into the groove provided for this purpose.
• Continue to check the seal regularly for dirt and damage!

Defrosting
CAUTION: Never use metal objects (e.g. knifes) to remove ice from the evaporator. Otherwise, it can be damaged.
During defrosting water drops drains off at the back of the cooling chamber. The thaw water running through a channel, is collected in a drip tray located on the compressor, where it will evaporate. Make sure the water discharge opening does not get clogged. A light formation of ice on the interior back during operation is normal. A permanently high power level can lead to increased ice formation → set a lower power level and wipe out the interior of the appliance.

Replacing the door hinge
If the appliance door starts to stutter, crack or jam when you open it, it is probably due to a worn or damaged hinge. It is recommended to replace all door hinges at the same time, otherwise the next repair will soon be beckoning.

• Remove the contents of the appliance and the movable interior parts.
• Tilt the appliance backwards and block it in this position to prevent the door from sliding out.
• Loosen the hinge cover as described under “Re-versing the door opening” and disassemble the upper door hinge.
• Turn out the stand and disassemble the lower door hinge.
• The respective hinge assembly is carried out in reverse order.
• Open and close the appliance door for a test run, readjust the hinges if necessary. In any case, make sure that the door fits tightly and accurately.

Troubleshooting

Before you contact an authorized specialist

Problem/cause   / action

Appliance is not working properly or at all
–    Check the power supply/temperature setting / ambient temperature.

–    Unblock the ventilation openings, install the appliance freely.

Loading is too warm
–    Check the temperature setting / ambient temperature.

–    A large quantity of warm food has been stored in the unit in the last 24 hours.

–    The appliance door is not closed properly, check the door seal.

Loud noise during operation
–    Check that the appliance is level.

–    See “Operating noise”.

Water on the appliance bottom
– Check the temperature setting/water discharge channel or opening.

Technical data

• Climate class N/ST: this appliance is intended to be used at ambient temperatures ranging from 16°C to 38°C.
• Electrical connection
  • Power voltage: …………………….220-240 V~ / 50 Hz
  • Rated power: …………………………….……..…..60 W
  • Rated current: …………………………………….0.24 A
• Dimension H x W x D / weight
  • Appliance size: ……..….………..51.0 x 45.0 x 45.0 cm
  • Net weight: ………………………….…approx. 15.0 kg

For more information about the product, scan the QR code on the supplied energy label and/or visit the official website of the product data bank: https://eprel.ec.europa.eu. The right to make technical and design modifications during continuous product development remains reserved. This appliance has been tested according to all relevant current CE guidelines, such as electromagnetic compatibility and low voltage directives, and has been constructed in accordance with the latest safety regulations.

Disposal

Meaning of the “Dustbin” symbol
Protect our environment; do not dispose of electrical equipment in the domestic waste. Please return any electrical equipment that you will no longer use to the collection points provided for their disposal. This helps avoid the potential effects of incorrect disposal on the environment and human health. This will contribute to the recycling and other forms of reutilization of electrical and electronic equipment. Information concerning where these can be disposed of can be obtained from your local authority. Your dealer and contractual partner is also obliged to take back the old appliance free of charge.

WARNING: Remove or disable any existing snap and bolt locks if you take the appliance out of operation or dispose it.

C. Bomann GmbH
www.bomann-germany.de
Made in P.R.C.

References

• elektro-service.de
• Bomann Startseite
• Bomann Service

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>