XIDU 550 ANSI 5G WiFi Bluetooth Projector User Manual

**XIDU 550 ANSI 5G WiFi Bluetooth Projector User Manual

**

Safety Precautions

Warnings

High brightness lamp! Don’t look straight into the lens when the projector s on.

1. Clean When clean this projector, please pull out the power cable. Use a wet cloth to clean, don’t use any detergent that may damage the unit.
2. Accessory Please use our recommended accessory. O it will damage the projector.
3. Correct environment Do not place the projector in a wet environment, like damp basement or near the swimming pool, etc.
4. Ventilation The ventilation is equipped for the projector to work stably. Do not put anything around the vents. O it wil cause the projector heating up.
5. Power Please make sure the power is within the required power range.
6. Thunder For thunder day, please unplug the power cable from the projector.
7. Repair Due to high voltage inside, please do not open or try to repair the projector by yourseff. Please ask a professional technician to repair the projector.
8. Keep away from heat device Please make sure the projector is far away from any heat devices which will damage the projector.

Warnings

• The projector i designed to operate on a power supply of following standard. Ensure that your power supply fits this requirement before attempting to use your projector.
  | Minimum| Rated| Maximum
  ---|---|---|---
  Volatage| 90Vac| 100-240Vac| 264Vac
  Frequency| 47Hz| 50Hz/60Hz| 63Hz
• Do not look into the lens while the projectors on. Serious damage to your eyes could result.

Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside your projector. Allow at least  inches (30cm) of space between your projector and a wall,

• Prevent foreign objects such as paper clips and bits of paper from falling into your projector. Do not attempt to retrieve any objects that might fall into your projector. Do not insert any metal objects such as awire or screwdriver into your projector. If ‘something should fall into your projector, disconnect it immediately and have the object removed by a qualified service personnel.
• Do not place any objects on top of the projector.
• Handle the power cord carefully. A damaged o frayed power cord can cause electric shock orfire.
  • Donot use any power cord other than the one supplied.
  • Donot bend or tug the power cord excessively.
  • Donot place the power cord under the projector, or any heavy object.
  • Do not cover the power cord with other soft materials such as rugs.
  • Do not heat the power cord.
  • Do not handle the power plug with wet hands.
• Tum off the projector and unplug the power cord if the projector is not to be used for an extended period of time

Product Overview

Note: If you want to return to the previous menu or signal source operation, please. press {x to return to the previous step.
Note: Please refer to the product appearance, this figure is for reference only.

Remote overview

Note: Batteries are not supplied in the package, you must purchase two additional AAA batteries by yourself

Note:

1. While using the remote control, point it toward IR receiver.
2. To avoid battery leakage corrosion, please take the batteries out if not use it fora long time.

Projection Size Chart

☆ Optimum projection distance: 3m

Operating Instructions

Four-Point Keystone Adjustment

1. Select £y enter the setting page

2. Choose “Projection Image Settings” and then select “Four Point Keystone” enter the following page. Follow the instructions on the screen, adjust it until the image is in correction position.

Horizon And Vector Keystone

Choose “Projection Image Settings” and then select “Horizon And Vector Keystone” enter the following page. Follow the instructions on the screen, adjust it until the image is in correction position.

Adjust Focus

1. Adjust the focus ring to make the picture clear

Input Resources

1. You can insert flash drive or hard drive in to the USD port, and the access the file storage in the drive.
2. You can connect your laptop or Vidoe player device (VCD/DVD ect) to the machine
3. Press the ] on remote can access the input resource interface. Choose the corresponding one, such as HD or AV to finish the connection

Bluetooth Connection

1. Bluetooth Output Select the 3 on the main interface or the Bluetooth Setting on the Setting page, choose your Bluetooth device to the pair the device, (Bluetooth mouse, Bluetooth Remote control, Bluetooth speaker, etc)

2. Under this mode, you can connect your phone of laptop to the machine, use the machine as a bluetooth speaker. Screen will automatically turn off when enter this mode. Click or O to exit this mode

3. Selection “Sound Bar “to enter the mode

4. Turn on the Bluetooth on your device and select the the speaker

5. There will be an audio notification from the Machine, when enter to exit the mode

Wireless Connection

PS: The fluency of screen mirroring with wireless connection will be affected by the network environment. A bandwidth of 100Mbit or more is recommended when using screen miroring. Make sure your mobile device is closed to the projector when using wireless connection. A distance within 1 meter is recommended.

Connecting with iOS and Android

i0S Connection (Air Play)

Notice: The iOS device and the projector needs to be connected to the same Internet for using the AirPlay.

1. In the main interface, select *Air Play”, press the “OK” to enter the interface.
2. Following the instructions on the Screen.

Wired Connection For I0S System Only

1. Turn on the projector, connect your iPhone or iPad to the USB port via ORIGINAL Lightning to USB cable (Charging cable) .
2. Select “Trust” in the pop-up window. Then it works.

Android Connection (Miracast)

Notice: Itis recommended that the projector is connected to the same router, or the WIFI of the Android device is not connected to any router.

1. Select “Miracast” in the main interface and press the “OK” to enter the interface
2. Turn on the “Wireless Display” of the Android device.
3. Select the corresponding projector device name.

For Android System: It doesn’t support cable connection. Please use the method of wireless connection only.

Other Connections

1. Connecting with PC

2. Connect projector with PC by VGA cable or HDMI cable.

3. Choose the media signal channel :”HD’

4. USB Multimedia Connecting

5. Insert the flash disk to USB interface.

6. Choose the media signal channel *USB”

7. According to the programs to choose “photos” “music” “movie” or “text’

8. Choose the file you want to play, press the key “play pause” to play or pause the file.

9. Connecting with MacBook or Mac Book Air

10. Choose the media signal channel :”HD”

11. Use a Type-C to HDMI cable to connect your MacBook, or a Mini Display to HDMI adapter to connect with your MacBook Air (adapter not included).

12. Connecting with Amazon fire TV Stick or other TV stick

13. Plug the TV stick into HD port of the projector.

14. Choose the media signal channel “HD”
    PS: It only supports 1080P TV stick, not 4K TV stick

15. Connecting with XBOX/PS4

16. Choose the media signal channel :”HD”

17. Use HDMI cable connect to XBOX/PS4

Main Menu Function

displayed
Projection Mode| Front/Front on Desk/Front on Ceiling/ Rear on ceiling| Choose the projection methods, flip the imag
Reduce Display| 100%-50%| Reduce the size of projection size

FAQ

with HDCPi This model doesn’t support this function So it can’t support these Apia
Wifi connection is not stable?|

• Please check whether the network of your phone is welli·
• Make the distance of phone and projector within 1 meteri· If still has a problem? Contact our after-sales service [email protected] immediately.

Indicator light is off when plug into power supply|

• The power cable not connected welli· The power button on the back of the projector is offi

Press the power button on the remote control and the projector does not turn on|

• The remote control’s batteries are depleted
•  Something obstructing the signal between the remote and IRi· Strong light on IR directlyi

No image on the screen|

• Is the channel set-up correct?· Is there input signal?· Is the input cable plugged well or in the wrong position?· Under PC mode, is the refresh rate > 75 KHz?

Picture right, no sound|

• Input cables connected right?· Volume at minimum or on Mutai· Turn off the Dolby of the input devices

It will shut off automatically after turn on for a while|

• Is there a barrier around the ventilation?· Low voltage or big voltage fluctuations· Check the over-heat protection systemi

Can’t find devices when connected with hard drive or flash drive?|

• Re-plug the device·
• Check if the device is broken

Can’t play the movies|

• The format of the video is right?· Files are broken?· Device is broken?

Contact us:

 [email protected]
[email protected]
 xidu-e.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>