WATCHARD 00-710 Analogue Watch User Manual

June 13, 2024
WATCHARD

WATCHARD 00-710 Analogue Watch

Product Information – Watch

This watch is manufactured by Zegarownia and the dealer’s address is Al. Witosa 31/106, 00-710 Warsaw. Please note that this user manual is the exclusive property of the dealer and its distribution without prior written consent is strictly prohibited.
The appearance of your watch may vary slightly from the one shown in the illustrations.

Analog Watches without a Second Hand

Setting the Time

  1. Pull out the crown.
  2. Set the hands by rotating the crown.
  3. Push the crown back in to resume timekeeping.

Analog Watches with a Second Hand or a Small Second Hand

Setting the Time

  1. When the second hand is at 12 o’clock, pull out the crown to stop it.
  2. Set the hands by rotating the crown. Move the minute hand four or five minutes past the desired setting, then back them up to the correct setting.
  3. Push the crown back in to resume timekeeping.

Analog Watches with a Multi-Date

Setting the Date

  1. Pull the crown out to the first click.
  2. Set the date by turning the crown. Avoid setting the date between 8:00 p.m. and 1:00 a.m., as the date display may not change to the following day.
  3. Push the crown in to the normal position.

Analog Watches with a Date Display

Setting the Time

  1. When the second hand is at 12 o’clock, pull out the crown to the second click to stop it.
  2. Set the hands by rotating the crown. Move the minute hand four or five minutes past the desired setting, then back them up to the correct setting.
  3. Push the crown back in to resume timekeeping.

Watches with a Rotating Bezel
Rotate the elapsed time bezel to align the () mark with the minute hand. After a certain amount of time has elapsed, read the graduation on the elapsed time bezel where the minute hand points to determine the elapsed time.

Analog Watches with a Day-Date

Setting the Time

  1. When the second hand is at 12 o’clock, pull out the crown to the second click to stop it.
  2. Set the hands by rotating the crown. Move the minute hand four or five minutes past the desired setting, then back them up to the correct setting.
  3. Push the crown back in to resume timekeeping.

Setting the Day and Day of the Week

SUN 30

Days of the Week (English, Spanish, and German)

ENGLISH SPANISH GERMAN
SUN MON TUE WED THU FRI SAT DOM MAR MIER JUEV VIER VIER SAB SON
MON DIE MIT DON FRI SAM

USER MANUAL

Dealer: Zegarownia, Al. Witosa 31/106, 00-710 Warsaw

This document is the exclusive property of the dealer and its distribution without the prior written consent of the dealer is strictly prohibited.
Your watch may differ somewhat from the one shown in the illustration.

Before using the watch for the first time

  • Depending on your watch model, there may be a spacer installed at the factory around the crown. If your watch has a spacer, you should remove the spacer before using the watch.
  • After removing the spacer, set up the watch for use.

Analogue watches without a second hand

To set the time
Pull out the crown. Set the hands by rotating the crown. Push the crown back in on a time signal to resume timekeeping.

Analogue watches with a second hand or a small second hand

To set the time

  1. When the second hand is at 12 o’clock, pull out the crown to stop it.
  2. Set the hands by rotating the crown. Move the minute hand four or five minutes past the setting you want, and then back them up to the setting.
  3. Push the crown back in on a time signal to resume timekeeping.

Analogue watches with a multi-date

Setting date

  1. Pull the crown out to the first click.

  2. Set the date by turning the crown.
    Avoid setting the date between the hour of 8:00 p.m. and 1:00 a.m. (The date display may not change in the following day).

  3. Push the crown in to the normal position.

Setting time and day of the week

  1. Pull the crown out to the second click when the second hand is at 12 o’clock position and the second hand stops.

  2. Set the hands by turning the crown. As you do, the day of the week changes accordingly.
    After setting day of the week, carefully set the time, making sure to distinguish between AM and PM.

  3. In accordance with a time signal, push the crown in.

24-hour hand
The 24-hour hand indicates the current hour of the day, making one complete rotation every 24 hours.WATCHARD-00-710-Analogue Watch
\(4\)

Analogue watches with a date display

To set the time

  1. When the second hand is at 12 o’clock, pull out the crown to the second click to stop it.
  2. Set the hands by rotating the crown. Move the minute hand four or five minutes past the setting you want, and then back them up to the setting.
  3. Push the crown back in on a time signal to resume timekeeping.

To set the day
Avoid setting the day between 8:00 p.m. and 2:00 a.m. The day may not change in the following day if you do.

  1. Pull out the crown to the first click.
  2. Set the day by rotating the crown.
  3. Push the crown back in to its normal position.

WATCHARD-00-710-Analogue Watch \(5\)Analogue watches with a day-date

To set the time

  1. When the second hand is at 12 o’clock, pull out the crown to the second click to stop it.
  2. Set the hands by rotating the crown. Move the minute hand four or five minutes past the setting you want, and then back them up to the setting.
  3. Push the crown back in on a time signal to resume timekeeping.

To set the day and day of the week

Avoid setting the day and day of the week between 8:00 p.m. and 4:00 a.m. The day and day of the week may not change in the following day if you do.

  1. Pull out the crown to the first click.
  2. Set the day by rotating the crown counterclockwise.
  3. Set the day of the week by rotating the crown clockwise. Confirm that the correct language is selected.
  4. Push the crown back in to its normal position.

WATCHARD-00-710-Analogue Watch \(7\)

Watches with a rotating bezel
Rotate the elapsed time bezel to align the (▽) mark with the minute hand. After certain amount of time elapsed, read the graduation on the elapsed time bezel which the minute hand points to. The elapsed time
is indicated.

Watches with a screw-down crown
Some water resistant models are equipped with a screw lock crown.
With such models, you must unscrew the crown
in the direction noted in the illustration to loosen it before you can pull it out. Do not pull too forcibly on such crowns.
Also note that such watches are not water resistant while their crowns are loosened. Be sure to screw the crowns back in as far as they will go after making any setting.

Analogue watches with a chronograph

WATCHARD-00-710-Analogue Watch \(9\)

To set the time

  1. When the second hand is at 12 o’clock, pull the crown out to the second click.
  2. Rotate the crown to set the time.
  3. Push the crown back in to its normal position.

Note

  • Take care that you set the correct AM or PM time.
  • When changing the time, move the minute hand four or five minutes past your final setting, and then back it up to the setting you want.

To set the day

  1. Pull the crown out to the first click.
  2. Rotate the crown to set the day.
  3. Push the crown back in to its normal position.

Note

  • The day indicator setting uses a 31-day month. Make adjustments for months of shorter lengths.
  • Avoid changing the day indicator setting between the hours of 9 p.m. and 1 a.m. Otherwise, the day indicator may not change correctly at midnight.

Solar-powered watchesSolar charging
A solar panel generates electrical power that charges a built-in (secondary) battery. The entire face is a solar panel, so power is generated when the face is exposed to light. Keep the watch exposed to light as much as possible.

Charging the battery

When you are not wearing the watch, leave it where it is exposed to light. For stable operation, expose the watch to at least a half day of light per month.
When wearing the watch, try to keep your clothing from blocking its face (solar panel). Charging efficiency is reduced significantly even if the face is blocked only partially.

Caution

  • The case of the watch may become quite hot when charging. Guard against burn injury after charging.
  • Avoid charging in the following locations, and anywhere else where the watch may become very hot.
    • On the dashboard of an automobile parked in the sun
    • Close to an incandescent light source or other sources of heat
    • Locations exposed to direct sunlight for long periods

Battery indicator
While the crown is pushed in, holding down the B button for about one second will cause the stopwatch second hand to move to a position that indicates the current battery level (about how long the watch can continue operating).

  • H : At least four months
  • M : Two to four months
  • L : No more than two months

After about two seconds, the hand will return to 12 o’clock.

Using the stopwatch
The stopwatch measures elapsed time in 1-second increments. The maximum time that the stopwatch can measure is determined by the watch movement.

Elapsed time

WATCHARD-00-710-Analogue Watch 14

Elapsed time

Caution

  • Do not operate the stopwatch with the crown pulled out.
  • An elapsed time operation will stop automatically once it reaches the maximum measurement.

Correcting the 0 positions of the hands
Perform the following procedure if the stopwatch hands do not return to their 0 (zero) positions when you reset the stopwatch.

  1. Pull the crown out to the second click.
  2. Use A (clockwise) and B (counterclockwise) to move the stopwatch second hand and stopwatch minute hand to 12 o’clock.
    • Holding down either button will move the second hand at high speed, until you release the button.
    • The stopwatch minute hand is synchronized with the stopwatch second hand.
  3. After all of the hands are the way you want, push the crown back in.

Important
Timekeeping stops while the crown is pulled out. Correct the current time setting after performing the above operation.

Low charge and dead battery conditions
An alert operation is performed when the battery charge goes low.

Low battery alert
The second hand will jump at two-second intervals to alert you when the charge is low.

WATCHARD-00-710-Analogue Watch \(12\)
Charging time
The times below are general guidelines for reference only.

exposure level (brightness) approximate charging time
to support daily use to recover from dead battery
to 1-second hand movement to full charge
outdoor sunlight (50,000 lux) 6 minutes
sunlight through a window (10,000 lux) 23 minutes

daylight through a window

on an overcast day

(5,000 lux)

| 36 minutes| 10 hours| 125 hours
indoor fluorescent lighting

(500 lux)

| 6 hours| 96 hours| – – –

A symbol of a crossed-out wheelie bin indicates that waste electrical and electronic equipment cannot be disposed of with other types of waste, but should be recycled separately. Waste equipment should be collected and handed over separately to a collection point
for recycling and other forms of recovery, as uncontrolled release of hazardous components contained in electrical and electronic equipment may pose a risk to human and animal health and have adverse effects for the environment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals