Smix CHM0166 Sunrise Plug in Digital Door Chime Instruction Manual

Smix CHM0166 Sunrise Plug in Digital Door Chime Instruction Manual

Transmitter
Exterior Door Press

Receiver
Indoor Chime Unit

PRODUCT INSTRUCTION

Thank you for purchasing this Smix Sunrise Plug-in Digital Door Chime. Simply plug the indoor chime to an AC outlet, mount the door press where needed and you are ready to go! The indoor chime can be expanded to work with up to 30 door presses or door chimes using a simple procedure in 10-15 seconds. Its working range is up to 100 metres in free air.

FEATURES

• Easy to Install and Use
• 58 Musical Melodies
• 5 Level Adjustable Volume
• Up to 100m Operating Range (free air)
• Flashing Light Designed for Hearing Impaired
• Expandable System – Just Add Door Presses
• IP55 Waterproof Door Press

PACKAGE CONTENTS

Receiver, Transmitter, 3V CR2032 button battery, and mounting kit.

TECHNICAL SPECIFICATIONS

Receiver

Voltage: 220-240V AC
Wattage: <2.0 Watts
Working Frequency: 433.92 MHz
Sound dB(A): 25-85 dB(A)
Operating Range (Free Air): Up to 100m

Transmitter

Battery (included): CR2032
Working Power: < 10mW
Push Button Rating: IP55
Operating Temperature -20°C to + 50°C

SELECTING YOUR MOUNTING LOCATIONS

Before fixing the products, check your desired locations can communicate first. The product is rated to operating up to a range of 100 metres in free air. The operating range will be reduced if the signal is transmitted through a number of walls or ceilings.

NOTE: Common barriers to avoid completely include mounting to any metal surface or UPVC door frames. Avoid positioning above heat sources such as radiators, or in damp areas such as a kitchen or bathroom. Do not expose either unit directly to rain or immerse in water. Do not locate either unit close to fireplace or expose to high temperatures.

Note the Receiver is suitable for Indoor use only. The Transmitter is rated for exposed exterior locations.

AFFIXING THE PRODUCTS

• The Receiver is plugged into a 230V power socket.
• Affix the door press to a smooth surface with double sided tape and screws as required. Before you drill any hole in the wall, please make sure there are not cables or pipes that you may accidentally damage.

SETUP THE AUTO-LEARNING CODE

What is Auto-learning Code?
The Transmitter sends a wireless signal to the Receiver. The Receiver would automatically register and memorize the signal as an operation code.
So the Transmitter can work with the Receiver by this code.

Auto-learning Code Set Up – Operation for 1 Transmitter and 1 Receiver

• After battery installation of the Transmitter, Plug the Receiver into a power socket.
• Firstly, select your desired melody. Factory default is ‘DING DONG’ sound.
• Then press and hold the Volume control button on receiver for 5 seconds. The Receiver will sound and light will flash, indicating the device is ready to pair.
• Press the transmitter button once. Pairing will be confirmed by playing of selected melody.

Expanding your system
You can pair up to 30 Transmitters to a single Receiver, by repeating steps above for each additional Transmitter (one at a time). Use items CHM0168 or CHM0169 Transmitters.

NOTE: If you require a different melody for different Transmitters, select new melody first before pairing. This may be useful for multiple entranceways to know which doorway is being visited. Alternatively, an additional door press may be used as a panic button.

It is important to remember that when you replace the run-out battery with new one that you may need to follow the same procedure of the auto-learning code set-up as above.

NOTE: Interference from another similar door chime operating nearby: To reset all settings, press the Music Forward Button for 5 seconds, then pairing will be relieved and melody turn into the default music -Ding Dong. Repeat steps above to re-pair.

SELECTING YOUR PERSONAL SETTINGS

There are 58 different melodies to select from. Scroll through these using the forward/backward melody buttons on the side of the Receiver to select your preferred melody. This can be changed at any time using the re-pairing steps.

There are 5 volume settings to select from. Scroll through these using the volume button on the side of the Receiver for the appropriate volume for your location. This can be changed at any time without re-pairing.

STRUCTURE DIAGRAM

Product Diagram (Receiver)

Product Diagram (Waterproof Transmitter)

INSTALLING THE BATTERIES

• Unscrew and lever the base off the top cover of the Transmitter.
  There is a small slot at the base of the unit to facilitate this.
  The base is held in place firmly, so some pressure may be required. It will not break, rather will pop open.

• Remove the circuit board (it may be secured with a small screw). Insert the supplied CR2032 into the battery holder, ensuring polarity of battery on installation. Reinsert the circuit board.

• Close the Transmitter enclosure by setting the fastening tab of the top cover into the slot on the base. Then carefully press the base into the top cover. It should click neatly into place, ensuring the waterproof rating of the Transmitter is maintained. Resecure base with screws.

OPERATION

Press the push button on the Transmitter unit once, it sends a wireless signal to the Receiver which will play the selected melody. The sound will stop as soon as the melody ends. For repeat sound, press the button again. Holding the Transmitter button IN will NOT repeat the sound.

USER HINTS

If the Receiver does not sound, please check the following:

• Flat batteries in the Transmitter -change the battery.
• Wrong battery polarity in the Transmitters-reinsert the battery.
• Units are out of range-relocate the Receiver within the operation range.
• Receiver has come unplugged from wall socket – plug in again.
• If leaving the chime unused for long periods, remove the battery from Transmitter to prevent leakage.
• Dispose of old batteries in accordance with the relevant legislation.

ELECTRICAL COMPLIANCE

This product complies to all relevant NZ/AU compliance standards.
An SDOC (supplier compliance declaration) is available on www.simx.co.nz Type the product code into Search on the home page, this takes you to the item product page, a download link is located below the product details on that page.

IMPORTANT: PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE WHEN REPLACING BATTERIES.

Distributed by: Simx Limited
Ph: +64 9 259 1660
Technical Support
Ph: +64 9 259 1662
Email: sales@simx.co.nz
www.simx.co.nz

Specifications are subject to change without notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>