AM20 Plantation Shutter Motor Manual Instructions

AM20 Plantation Shutter Motor

Motor Features

• User friendly removable battery case; accept 5V type-C USB charging
• Built-in 900mAh rechargeable lithium battery. Motor can connect with solar panel extending running time.
• Compatible both Bluetooth bi-directional communication control and radio frequency remote control.
• Featuring rational light tilting mode and one touch tap-to-run mode.
• The push/pull force is up to 50N (5kgs).
• Running speed 8mm/s, quick response.
• Various fixed methods are available, screws fixed and 3M adhesive tape.

Motor Specification

Push/ Pull Power

| Running Speed| Running Distance| Rated Power| Charging Voltage| Battery Capacity| Standby Time| RF Frequency| IP Class| Operating Life| Working Temperature
---|---|---|---|---|---|---|---|---|---|---
50N| 8mm/s| 0-82mm| 2W| 5VDC| lithium battery 900mAh| 3 months (It is recommended to charge every three months)| 433.92MHz| IP 32| 15000 times|

-10°c -+ss0c

Accessory

Installation Instructions

Shutter Louver Clips Installation Method

In order to achieve better light blocking effect, the clip is recommended to install onto the middle louver of the shutter.

1. Choose the hook with right size.

2. Rotate shutter louver to a horizontal level.
   

3. Put the clip on the louver, there are two sides of the hook, the longer side attach to the louver first.

4. Make the shorter side attach to the louver, make sure the two sides of clip are well attached to louver.
   

5. The clip is well installed now.

Plantation Motor Installation Method

Preparation

1. When the clip is well installed, make the shutter louvers fully closed.
2. The driving rod of the motor should run to the lowest limit (the default limit of the motor is lower limit), and insert the rod to the arc-shaped hole of the hook.
3. Pull the motor straightly down, make sure the shutter louvers are tightly closed, and mark down the position of the motor.

Fixed the Motor

Method 1: Screw Fixed

• Fix the motor onto shutter and mark position.
• Use Phillipe screwdriver to fix two screws on the motor (like the right picture (1)), the screws are in the accessory kit package.
• Attached the clip to motor rod, lock the screw nuts.
• Press the two screw caps into the screw holes, Motor installation completed.

Method 2: 3M Adhesive Tape Fixed

• Put the 3M adhesive tape on motor (like right picture (2)), don’t attach the adhesive tape on battery pack.
• Install the motor on the marked position.
• Attached the clip to motor rod, lock the screw nuts.
• Press the two screw caps into the screw holes, Motor installation completed.

Operating Instructions

Enter Pairing Mode

Pair to Remote

Reverse Motor Direction

Switch Light Tilting Mode and Tap-to-Run Mode

• In tap-to-run mode, if middle limit has been set, the motor will stop on middle limit, press UP or DOWN, motor will move to next limit position.
• In light tilting mode, short press UP/DOWN, motor will only tilt in rational angel, while long press UP/DOWN >2s, the motor will run continuously. If middle limit has been set, the motor will stop on middle limit.

Movement Calibration Function (One Short Press + One Long Press)

Movement Calibration Function: Automatically capture and save physical upper and lower limits, this will help to protect the motor case. When motor is in movement calibration mode, the push/ pull power will be reduced so that motor can be easier to record the max journey. it’s recommended to calibrate the journey each time before installation in no-load condition.

Delete Single Channel

Delete All Memories

Adjust Upper / Lower Limits

When movement calibration finished, the default upper limit is max journey calibration, and the lower limit is minimum journey calibration.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>