THDssF High-Performance DAC E30 II-E30 II Lite User Manual
- June 13, 2024
- THDssF
Table of Contents
THDssF High-Performance DAC E30 II-E30 II Lite User Manual
Thank you for purchasing high-performance DAC E30 I/E30 1l Lite. We hope it could bring you more fun at enjoying music! Before making any connections or using this product, we recommend you read this manual irst o that you can use all the features of E30 11/E30 II Lite correctly and get the most listening pleasure.
Contents list
E30I/E30NILite: x1
DC cable: x1
USB cable: x1
Remote control: x1
User manual: x1
Warranty card: x1
Note: You can download the driver and user manual on http://www.topping audios/.
Attribute
Measured : 10.0cm x 12 56m x 3 26m
Weight: 2059
Power input : DCSVIIA
Signal input : USBIOPT/COAX
Line Out : output RCA
Front panel
- 1-1 LED screen
- 1-2 Remote control receiver
- 1-3 Multifunction touch button
Rear panel
- 21 Right channel single-ended RCA output
- 2-2 Left channel single-ended RCA output
- 2-3 Coaxial SPDIF input
- 24 Optical SPDIF input
- 2-5 USB input
- 2-6 Power input (DC5V/1A)
Display
- 3-1 Input channel (1fthe current inputs connected successfully, the current input indication is always on, otherwise, the indication flashes.)
- 3-2 Sample rate indication (in DAC mods) or volume indication (in PRE mode) +
- 3-3 PGMIDSD format indication * In PRE (Pre-amplifier) mode, the £30 IVE30 11 Lite will always display the volume level. When the sampling rate of the input signal changes, twill display the sampling rate for 25 and then continue displaying the volume level; In DAC mode, the £30 I/E30 11 Lite will always display the sampling rate, keep the maximum volume output and the volume is not adjustable. Please refer o the Setup Menu to switch the output made.
Remote control
“Note:
“L-A” has the same brightness as “L-2”. The differences li n when there s no operation after 30 seconds under “L-A” mods, the screen will be automatically trend off, only splays the current input. You can press any button o light up the screen.
Input range
| USB IN | PCM 44, 1kHz-768KHz/16bIL-32011 |
|---|
DSD DSD84-DSDS12 (Native) . DSDS4-DSD256 (DoP)
GOAXIOPTIN| |PCM 44, 1ktHz-192kHz/16bit-248it
Specifications
E30 II/E30 II Lite DAC (LineOut/USB In@96kHz)parameters
| E30 II| E30 II Lite
THD+N @1kHz (A-wt)| <0.00015%| <0.00020%
THD @90kBw (No-wt)| <0.00060% @20-20kHz| <0.00040% @20-20kHz
SNR (A-wt)| 123dB @1kHz| 121 dB @1kHz
Dynamic range (A-wt)| 123dB @1kHz| 121 dB @1kHz
Frequency Response| 20Hz-20kHz (±0.3dB)| 20Hz-20kHz (±0.3dB)
20Hz-40kHz(±0.8dB)| 20Hz-40kHz (±0.8dB)
Output Level| 2.1Vrms @OdBFS| 2.1Vrms @OdBFS
Noise (A-wt)| <1.5uVrms| <1.9uVrms
Channel Crosstalk
@1kHz| -132dB @1kHz| -137dB @1kHz
Channel Balance| <0.3dB| <0.3dB
Output Impedance| 200| 200
Note: The above data is the result of the test in TOPPING laboratory.
Operation
Power on & off / standby operation:
- Power on: When connects to power supply, E30 II/E30 II Lite goes into the standby state, the screen displays a bright dot.
- Standby setting: When it is working, press and hold the multi-function touch button on the front panel to enter standby state and short press to exit standby state when it is in standby. Or you can directly press the standby button on remote control to enter or exit standby state.
Note:
When the automatic standby function is on, if the current input is not
connected or input signal is invalid in 1 minute, it will automatically enter
he standby state. Once having detected valid signal, it will automatically
return to working state.
Volume setting:
- The enter and exit of mute state: Press the mute button on the remote control to set mute, press the mute button again or adjust the volume to exit mute state.
- Volume adjusting: Adjust volume by pressing the up/down button on the remote control. Press and hold the up/down button will quickly adjust the volume, so please be careful in order to protect your hearing. Note: Volume is fixed to 0dB in DAC mode and volume adjusting is invalid inthis mode .
Input channel switching:
Press the multi-function touch button on the front panel or the “Switch to
previous input button” and the “Switch to next input button” on the remote
control to switch the input in cycle.
Setup Menu
Enter the setup menu:
In the standby state, press and hold the multi-function touch button on the
front panel for 5 seconds to enter the setup menu of E30 II/E30 || Lite.
Change and save of settings:
- The touch button on the front panel: press the touch button to enter the next setting item, double press the touch button to set different parameters. Press and hold the touch button until “8-8” is displayed on the screen to save the settings.
- The remote control: press the volume up/down button to enter the previous/next setting item, press the left/right button to set different parameters. Press the OK button and E30 II/E30 II Lite displays “8-8” indicating that the settings have been saved.
Setting descriptions
PCM filter setting (available for remote control setting, set PCM filter mode
when playing PCM)
| Screen display | Description |
|---|---|
| F-1 | Sharp Roll-off |
| F-2 | Slow Roll-off |
| F-3 | ShortDelay Sharp Roll-off (Default) |
| F-4 | Short Delay Slow Roll-off |
| F-5 | Super Slow Roll-off |
| F-6 | Low Dispersion Short Delay Filter |
DSD filter setting (available for remote control setting, set DSD filter mode when playing DSD
| Screen display | Description |
|---|---|
| F-1 | 39kHz (Default) |
| F-2 | 76kHz |
Screen brightness setting (Available for remote control setting)
| Screen display | Description |
|---|---|
| L-1 | Low |
| L-2 | Mid (Default) |
| L-3 | High |
| L-A | Mid brightness and screen will be turned off |
automatically after 30 seconds of no operation
Automatic standby setting (Available for remote control setting)
| Screen display | Description |
|---|---|
| A-O | Auto on (Default) |
| A-C | Auto off |
Output mode setting
| Screen display | Description |
|---|---|
| m-p | Per-Amp mode (Volume adjustable) (Default) |
| m-d | DAC mode (Volume nonadjustable |
Remote control setting
| Screen display | Description |
|---|---|
| r-O | Remote control enabled (Default) |
| r-C | Remote control disabled |
Factory reset:
In standby mode, press the Volume down, Volume up and Mute buttons on the
remote control in sequence to restore the factory settings.
Trouble shooting
| Phenomenon | Cause | Solution |
|---|---|---|
| Input indicator flashes | Unknown signal format | Change to correct format |
| Signal cable did notconnected properly | Check or change the cable | |
| No signal input | Check the player | |
| USB did not recognize | USB cable did not connect properly | Check or change the |
cable
PC’s USB port damaged| Change another port
The PC does not work| Check or try with another PC
The OTG function of thephone is not enabled| Enable OTG function
USB input, no sound| Too low volume on PC| Adjust volume
E30 II/E30 II Lite is not selected as the output device on the PC| Set the E30
II/E30 II Lite as the default output device
INH Err| Supply voltage too high| Please use DC5V power supply
INL Err| Supply voltage too low| Please use DC5V power supply
If you still have problems or questions, please contact us (service@tpdz.net)
Precautions for daily use
- The output jacks shall not be grounded or short-circuited.
- You must not keep the E30 II/E30 II Lite in a hot, humid environment or drop it.
- Opening the case instantly voids the warranty!
- Topping accepts no liability for any loss or damage arising directly or indirectly from the failure of E30 II/E30 II Lite.
- For improvement purpose, specifications subject to changes without prior notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>