Inverto IDLP-WDB400-E1040-OPN Wideband LNBs User Manual
- June 13, 2024
- inverto
Table of Contents
Inverto IDLP-WDB400-E1040-OPN Wideband LNBs
Product Information
The Wideband LNBs are satellite signal receivers designed to be used with a
satellite dish antenna equipped with a 40mm LNB holder.
They allow for the reception of satellite signals in the Ku band.
Models:
- 6047 Wideband 40mm PLL LNB with Horizontal/Vertical ports, LO 10.40 GHz (EU) IDLP-WDB400-E1040-OPN
- 6048 Wideband 40mm PLL LNB with Horizontal/Vertical ports, LO 10.41 GHz (UK) IDLP-WDB401-U1041-OPN
Technical Data:
Item#| Frequency Range (GHz)| Frequency Range (MHz)| Local Oscillator
Frequency (GHz)| Noise Figure (dB)| Ports| Impedance (Ohms)| Operating Voltage
(VDC)| Operating Current (mA)| Dimensions (mm)| Weight (g)
---|---|---|---|---|---|---|---|---|---|---
6047/6048| 10.7 ~ 12.75| 300 ~ 2350 / 290 ~ 2340| 10.40 /10.41| 23dB typical|
2 F-type ports| 75| 11 ~ 20| 100 max.| 40| 98
Product Usage Instructions
Installing the LNB on the dish antenna
-
Place the LNB in the LNB holder/clamp of the dish antenna.
Close the LNB holder handle and lightly tighten the clamp screw so that the LNB can still rotate. -
Set the correct tilt angle of the LNB by rotating it clockwise or counterclockwise. The tilt angle depends on the location of the satellite dish antenna installation and the satellite to adjust.
Use a satellite signal meter or a satellite receiver measurement indications for adjustment. -
After determining the correct position of the LNB, tighten the screws that secure the LNB clamp so that the LNB is fixed in its place.
-
If your satellite dish is not correctly installed and aligned towards the desired satellite, complete the installation and correct alignment before proceeding with the LNB installation.
-
We strongly recommend that the satellite dish antenna is installed by a qualified satellite antenna installer.
Connecting the antenna cable to the LNB
- Attach the protective rubber boot to the antenna cable.
- Strip the cable insulation and screw the F-plug onto the end of the cable.
- Ensure that the braided wires and the center conductor are not touching each other as this degrades signal quality.
- Screw in the F-plug to connect the antenna cable to the LNB.
- Slide the protective rubber boot into its collar tip at the LNB housing.
Note: The F plug is sold separately and is not included with the LNB.
Models
6047 Wideband 40mm PLL LNB with Horizontal/Vertical ports, LO 10.40 GHz (EU)
IDLP-WDB400-E1040-OPN 6048 Wideband 40mm PLL LNB with Horizontal / Vertical
ports, LO 10.41 GHz (UK) IDLP-WDB401-U1041-OPN
General Information
Please read the information contained in this manual before installing the
LNB.
The operations described in the instructions must be carried out in the order
presented.
Product Description
- The LNB is intended for use with a satellite dish antenna equipped with a 40mm LNB holder for mounting.
- The LNB allows receiving satellite signals in the Ku band.
Installation & Safety
Warning! The LNB and the satellite dish antenna shall be installed by a qualified satellite antenna installer, and in compliance with safety regulations.
- Do not install the LNB during a storm or other extreme weather conditions.
- Connect the coaxial cable to the LNB before connecting the set top box.
- Carry out your satellite dish and LNB installation with tools and accessories intended for this purpose only.
Installing the LNB on the dish antenna
- Place the LNB in the LNB holder/clamp of the dish antenna. Close the LNB holder handle and lightly tighten the clamp screw so that the LNB can still rotate (Fig. 1).
- Set the correct tilt angle of the LNB by rotating the LNB clockwise or counterclockwise: The tilt angle of the LNB (K) depends on the location of the satellite dish antenna installation and the satellite to be received. For example, for receiving Hotbird at 13°E in Warsaw, the tilt angle of the LNB should be 6° counterclockwise. Fine angle adjustment turning should be done using a satellite signal meter or a satellite receiver measurement indications (Fig. 2).
- After determining the correct position of the LNB, tighten screws that secure the LNB clamp so that the LNB is fixed in its place (Fig. 3).
- The above description of the LNB installation applies to the case when the satellite dish is correctly installed and aligned towards the desired satellite. In other cases, you must complete the installation and correct alignment of your satellite dish first.
- We strongly recommend that the satellite dish antenna is installed by a qualified satellite antenna installer.
Note: Product images are for illustrative purposes only and may differ from the actual product.
Connecting the antenna cable to the LNB
- Attach the protective rubber boot to the antenna cable.
- Strip the cable insulation and screw the F-plug* onto the end of the cable (Fig. 4).
- Make sure the braided wires and the center conductor are not touching each other as this degrades signal quality.
- Screw in the F-plug to connect the antenna cable to the LNB.
- Slide the protective rubber boot into its collar tip at the LNB housing.
F plug is sold separately. It is not included with the LNB.
Technical data
- Parameter Item# 6047/6048
- Input signal GHz 10.7 ~ 12.75
- Output signal MHz 300 ~ 2350 / 290 ~ 2340
- Local Oscillator (L.O.) GHz 10.40 /10.41
- Cross polarization isolation dB 23dB typical
- Output ports / impedance -/Ω 2 F-type ports / 75
- Input DC voltage level VDC 11 ~ 20
- DC current consumption mA 100 max.
- Neck diameter (Ø) mm 40
- Weight g 98
Simplified EU Declaration of Conformity
FTA Communication Technologies S.á r.l hereby declares that the LNB converter
type 6047, 6048 meets the essential requirements of the following directives:
- RED 2014/53 / EU
- RoHS 2011/65 / EU
A copy of the full text of the EU declaration of conformity can be found at: www.inverto.tv/support_dc
WEEE Notice
Environmental protection is an important objective of our company.
The crossed out waste container means that this product cannot be disposed of
as waste after it has ended from the household, but must be disposed of in a
special place. We hereby inform you that the main purpose of the regulation
European and the Act of 11 September 2015 on waste electrical and electronic
equipment is to limit the amount of waste arising from equipment, ensuring an
appropriate level of collection, recovery and recycling of used equipment, and
increasing public awareness of its harmfulness to the natural environment at
every stage of its use.
Pursuant to art. 36 above of the Act, the user of equipment intended for
households is obliged to return used equipment to the collector waste
equipment or the entity authorized to collect waste equipment referred to in
art. 45 item 1 point 1 of the Act of December 14 2012 on waste.
With all this in mind, it should be stated that in the above process,
households have to meet very important role. However, it should be remembered
that products belonging to the group of electrical or electronic equipment
should be utilized in the right way and in the right places. Information on
local collection points (storage site, collection point, etc.) can be provided
by local authorities or the distributor.
At the same time, it should be emphasized that distributors are obliged to
take back waste equipment from households free of charge at the point of
sale,provided that the waste equipment is of the same type and performed the
same functions as the equipment sold. In addition, the distributor, providing
the buyer with equipment intended for households, is obliged to take back free
used equipment from households at the place of delivery of that
equipment,provided that the waste equipment is of the same type and has the
same functions as the equipment supplied. In this way you can participate in
the process of reusing raw materials and supporting the electrical and
electronic waste management program, which may affect environment and public
health. It should be remembered that the correct disposal of equipment allows
saving valuable resources and avoiding negative effects on health and the
environment, which may be threatened by inappropriate handling of waste and
components dangerous.
Importer
FTA Communication Technologies S.à r.l
17 Route de Luxembourg, Gonderange L-6182
Luxembourg
For further details contact: sales@inverto.tv
FTA Communication Technologies S.á r.l
Tel. +352 264 367 1
Fax. +352 264 313 68
17 Route de Luxembourg, Gonderange, L-6182, Luxembourg
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>