In HOUSE LED SO29 Solar LED Projector User Manual

In HOUSE LED SO29 Solar LED Projector

Product Information

The product is a multifunction solar LED projector. It is available in black color and has a power output of 10W. The lumens produced by the LED are 1100LM, and the color temperature is 4000K. The LED is made up of SMD2835x55PCS. The device operates on a 3.7V battery with a capacity of 7200mAh. It has a double silicon monocrystalline solar panel with a power output of 6.5Wp+4.5Wp. The product is IP65 rated, providing protection against dust and water ingress. It comes with a warranty of 2 years for the light and 12 months for the battery. The recommended installation height is less than 5 meters.

Product Usage Instructions

1. Installation: There are two installation options:
   • Installation 1: Wall installation of the set.
   • Installation 2: Placing the projector on a flat surface. Push aside the product support and position it on a flat surface.
2. Operation: The device has different modes of operation.
   • Mode A: Separate Operation – The lamp works without the solar panel connected. Light sensor and PIR sensor are disabled. The lamp works at constant brightness.
   • A1 mode: Press the button 1st time to light up with 30% brightness.
   • A2 mode: Press the button 2nd time to change to 100% brightness.
   • A3 mode: Press the button 3rd time to turn off the lamp.
   • Mode B: Working Together – The lamp works with the solar panel connected. Light sensor and PIR sensor are activated automatically.
   • B1 mode: Press the button 1st time to turn on to 100% brightness (1100lm) at night when motion is detected in the range of 8m. It will then dim to 5% brightness after 20 seconds without motion.
   • B2 mode: Press the button 2nd time to automatically light up at night and stay at 100% brightness (1100lm). After 5 hours or when the battery capacity is less than 30%, it will switch to B1 mode.
   • B3 mode: Press the button 3rd time to turn off the lamp.
   • Mode C: Power bank – The lamp works as a power bank with charging and discharging function.
   • DC interface: External microphone with DC5V input and a maximum charging current of 1.5A.
   • USB external DC interface: DC5V, 1.0A. Can charge mobile phones 2-3 times.

This user manual should be read carefully as it contains important notes on the safety, use and maintenance of your device.

Keep it in a safe place and transmit it if the device changes ownership

TECHNICAL DATA

NOTICE

1. This is a solar powered lamp, please install it in a place where there can be enough sunlight.
2. Please note that working time depends on sunshine duration and weather.
3. When the lamp is connected to the solar panel, it will automatically turn on at dusk and turn off at dawn.
4. The recommended installation height for wall mounting is 3-4 meters, for hanging on the wall is less than 2 meters.
5. Built-in smart IC has over-charge, over-discharge and over-voltage protection.
6. The lamp is equipped with an internal replaceable battery. If needed, please contact the seller for a new correct battery.
7. Amateurs, please do not disassemble the lamp.
8. Please do not dispose of the battery with household garbage to avoid explosion.

OPERATION

Mode A: Separate Operation
The lamp works separately without solar panel connected, the light sensor and the PIR sensor are both disabled, the lamp works at constant brightness.

• A1 mode: Press the button 1st time, it lights up with 30% brightness.
• A2 mode: press the button 2nd time, it changes to 100% brightness.
• A3 mode: Press the button 3rd time, it turns off.

Mode B: Working Together
The lamp works with solar panel connected together, both light sensor and PIR sensor will be activated automatically.

B1 mode:
Press the button 1st time, automatically turn on to 100% brightness (1100lm) at night when motion detected in the range ≤8m, then dim to 5% brightness in 20 seconds without motion.

B2 mode:
Press the button 2nd time, automatically lights up at night and constantly stays at 100% brightness (1100lm), after 5 hours or when the battery capacity is less than 30%, it will switch to B1 mode .

• Mode B3: Press the button 3rd time, it turns off.

Mode C: Power bank
The lamp works as a power bank with charging and discharging function.

DC interface → External microphone: DC5V, the maximum charging current is 1.5A.

• External DC5V input is required, current is not limited. However please note that the maximum charging current of Micro is 1.5A.

• It takes about 5 hours for a full 1.5A charge.
  USB → external DC interface: DC5V, 1.0A

• Can charge mobile phone 2-3 times.

INSTALLATION

Installation 1: Wall installation of the set

1. Prepare the lamp, accessories and tools well, confirm the installation location and wire length. (Figure ①)
2. Use the device to correctly measure the position of the hole, and drill 4 holes of Φ8mm with a depth of 60mm on the wall. (Figure ②)
3. Fix the expansion screws in the holes with free space, then fix the solar panel and LED lamp. (Figure ③)
4. Open the silicone cover at the bottom of the lamp, connect the solar panel wire to the lamp, and screw it tight. (Figure ④)
5. Adjust the solar panel and LED lamp to the correct position. (Figure ⑤)

Installation 2: Lay the projector on a flat surface only
Push the product stand aside and place it on a flat surface.

Installation 3: Fix the projector only

1. Please drill 2 Ø8mm holes on the wall with 88.5mm spacing.
2. Fix the dowels and expansion screws in the holes with free space (do not lock on the bottom).
3. Spread the stand stand apart, align the hanging holes with the screws and hang the lamp on the wall.
   • The recommended suspension height is less than 2 meters.

GENERAL SAFETY NOTES

• This device is not intended for use by persons (including children) with limited physical, sensory or mental capabilities or with no experience or knowledge, unless under the supervision of a person in charge of the device. their safety or if they have received instructions from a person on how the device should be used.
• Children should be supervised to make sure they do not play with the device.
• If a power cable is damaged, it must be replaced by a professional to avoid any risk of injury or accident, as well as damage to the device.
• Always unplug your appliance before cleaning and if it is defective.
• Never immerse the device in water. It is not suitable for underwater use. Risk of electrocution!
• Do not operate the appliance if it has fallen into the water and the plug or appliance is damaged.
• Make sure that neither the power cable nor the appliance is placed on hot surfaces or near sources of heat. Lay the power cable so that it does not come into contact with hot or sharp objects. Risk of electric shock !
• Although the power cable is sturdy, it should never be bent as this can cause cable breakage. Risk of electric shock !
• Never try to open the device with metal objects. This voids your warranty and carries a risk of electric shock!
• Electrical devices are not toys! Use and store the device out of the reach of children. Never let the power cable hang so that it can not be pulled.
• Repairs can only be done by professionals. Devices that have not been professionally repaired pose a risk to the user.

Only connect the device to an outlet with the correct power supply voltage.

• Use the appliance only on stable surfaces.
• Never use the device if the power cable is damaged. Contact a specialist to see if the cable is serviceable.
• Only use components and accessories recommended by the manufacturer and designed for this purpose.
• Before plugging in the appliance, always make sure that the plug, the power cable and your hands are dry.
• Unplug your appliance before cleaning.
• Do not use abrasive cleaners for cleaning.
• Never immerse the device in water

INITIAL VERIFICATION/DEFECTS AND RESOLUTION

• After unpacking the appliance, check that it is not broken or damaged. If in doubt, do not use your device, but rather contact your dealer.
• The device is supplied in a packaging for protection.
  • Remove the appliance from all its packaging.
  • Clean the device and all accessories of the packaging residues.
• Unscrew the power cable completely.
• Place the device in a suitable place on the mounting bracket.
• Make sure the bracket is attached to a stable, secure surface.

NOTES OF USE

• The product packaging is made of recyclable materials. It can be recycled.
• The device must be disposed of properly at the end of its service life in accordance with the statutory regulations.
• The materials must be reused according to their designation. This means that the recyclable material in the device can be reused and thus contribute to the protection of the environment.
• Further information can be obtained from the relevant municipal administrative authorities or from your local waste disposal company.

www.my-netelec.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>