Panasonic PT-DW830 1DLP 8500 lumens Projectors User Manual

CONNECT

PT-DW830 1DLP 8500 lumens Projectors

1DLP – 8500 lumens – WXGA – 2Lamps – Exchangeable lens – Dynamic RGB Booster – Digital Link
PT-DW830
10000 lumens-class fixed installation projector Delivering stunning colours and highly flexible projection for museums, exhibitions and digital signage applications

Key Features

1-Chip DLP, 8500 lumens, WXGA
Excellent image quality thanks to the dynamic RGB Booster and Vivid Colour Control
Dual lamp system with lamp relay mode enables 24/7 operation
Eco filter enables up to 12000 hours of air filter replacement cycle
10,000:1 contrast ratio

Power Consumption (120-240V AC,
50/60Hz)| 1,030 W (1,060 VA) (0.3 W with STANDBY MODE set to ECO, 3 W with STANDBY MODE set to NORMAL)
DLP™ Chip Panel Size| 16.5 mm (0.65 in) diagonal (16:10 aspect ratio)
DLP™ Chip Display Method| DLP™ chip x 1, DLP™ system
DLP™ Chip Pixels| 1,024,000 (1,280 x 800) x 1, total of 1,024,000 pixels
Lens PT-DW830K/DW830W| Powered zoom/focus lenses (1.8 – 2.5:1), F 1.7 – 1.9, f 25.6 – 35.7 mm
Lens PT-DW830LK/DW830LW| Optional powered zoom/focus lenses and fixed-focus lens
Lamp| 420 W UHM lamps (x 2)
Screen Size| 1.27 – 15.24 m (50 – 600 inches) (1.27 – 5.08 m (50 – 200 inches) with the ET-DLE055 (16:10 aspect ratio)) (2.54 – 8.89 m (100 – 350 inches) with the ET-DLE030 (16:10 aspect ratio))
Brightness| 8,500 lumens (dual lamp, LAMP MODE: NORMAL)
Center-to-Corner Uniformity| 90%
Contrast| 10,000:1 (full on/full off, in dynamic iris 3 mode)
Resolution| 1,280 x 800 pixels(Input signals that exceed this resolution will be converted to 1,280 x 800 pixels.)
Scanning Frequency (HDMI/DVI-D)| fH: 15 – 100 kHz, fV: 24 – 120 Hz, dot clock: 25 – 162 MHz
Scanning Frequency (RGB)| fH: 15-100 kHz, fV: 24-120 Hz, dot clock: 162 MHz or lower
Scanning Frequency YPBPR (YCBCR)| 525i(480i): fH 15.75 kHz; fV 60 Hz, 625i(576i): fH 15.63 kHz; fV 50 Hz, 525p(480p): fH 31.50 kHz; fV 60 Hz, 625p(576p): fH 31.25 kHz; fV 50 Hz, 750(720)/60p: fH 45.00 kHz; fV 60 Hz, 750(720)/50p: fH 37.50 kHz; fV 50 Hz, 1125(1035)/60i: fH 33.75 kHz; fV 60 Hz, 1125(1080)/60i: fH 33.75 kHz; fV 60 Hz, 1125(1080)/50i: fH 28.13 kHz; fV 50 Hz, 1125(1080)/25p: fH 28.13 kHz; fV 25 Hz, 1125(1080)/24p: fH 27.00 kHz; fV 24 Hz, 1125(1080)/24sF: fH 27.00 kHz; fV 48 Hz, 1125(1080)/30p: fH 33.75 kHz; fV 30 Hz,
1125(1080)/60p: fH 67.50 kHz; fV 60 Hz, 1125(1080)/50p: fH 56.25 kHz; fV 50 Hz
Scanning Frequency (Video/Svideo)| fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60]; fH: 15.63 kHz, fV: 50 Hz
[PAL/PAL-N/SECAM]
Optical Axis Shift| Vertical: +60% (powered), Horizontal: ±10% (powered); NOTE: Optical axis shift function
cannot be operated when used with the ET-DLE055. If using the ET-DLE030, the optical
axis is fixed.
Keystone Correction Range| Vertical ±40° (±30° with the ET- DLE055/DLE085/DLE105.)
Cannot be used when the ET-DLE030 is installed.
Installation| Ceiling/floor, front/rear
Terminals HDMI In| HDMI 19-pin x 1, Deep Color, compatible with HDCP, 525i(480i), 625i(576i), 525p(480p), 625p(576p), 750(720)/60p, 750(720)/50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p, 1125(1080)/50p, VGA(640 x 480) – WUXGA(1,920 x 1,200), dot clock: 25 MHz -162 MHz;
NOTE: Compatible with non-interlaced signals only.
Terminals DVI-D In| DVI-D 24-pin x 1, DVI 1.0 compliant, HDCP compatible, for single link only; 525i(480i), 625i(576i), 525p(480p), 625p(576p), 750(720)/60p, 750(720)/50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p, 1125(1080)/50p; VGA(640 x 480) – WUXGA(1,920 x 1,200), dot clock: 25 MHz -162 MHz; NOTE: Compatible with non-interlaced signals only.
Terminals RGB 1 In| BNC x 5
Terminals RGB 1 In R, G, B| R: 0.7 Vp-p, 75 ohms; G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms; B: 0.7 Vp-p, 75 ohms; HD, VD/SYNC: TTL, high impedance, positive/negative automatic;
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Terminals RGB 1 In Y, PB, PR (Y, CB, CR)| Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms
Terminals RGB 1 In S-Video Signal| Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms
Terminals RGB 2 In| D-sub HD 15-pin (female) x 1
Terminals RGB 2 In R, G, B| R: 0.7 Vp-p, 75 ohms; G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms; B: 0.7 Vp-p, 75 ohms; HD, VD/SYNC: TTL, high impedance, positive/negative automatic;
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Terminals RGB 2 In Y, PB, PR (Y, CB, CR)| Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms
Terminals 3D Sync 1 In/Out| BNC x 1, 1.0 Vp-p, 75 ohms Input: TTL, high impedance. Output: TTL, max. 10 mA
Terminals 3D Sync 2 Out| BNC x 1, 1.0 Vp-p, 75 ohms, TTL, max. 10 mA
Terminals Video In| BNC x 1, 1.0 Vp-p, 75 ohms
Terminals Serial In| D-sub 9-pin (female) x 1 for external control (RS-232C compliant)
Terminals Serial Out| D-sub 9-pin (male) x 1 for link control (RS-232C compliant)
Terminals Remoter 1 In| M3 jack x 1 for wired remote control
Terminals Remoter 1 Out| M3 jack x 1 for link control
Terminals Remoter 2 In| D-sub 9-pin x 1 for external control (parallel)
Terminals LAN/DIGITAL LINK| RJ-45 x 1 for network and DIGITAL LINK (video/network/serial control) connection, 100Base-TX, compatible with Art- Net, compliant with PJLink™ (class 1), Deep Color, compatible with HDCP, 525i(480i), 625i(576i), 525p(480p), 625p(576p), 750(720)/60p750(720)/50p, 1125(1080)/60i,  125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 125(1080)/60p, 1125(1080)/50p; VGA(640 x 480WUXGA(1,920 x 1,200), dot clock: 25 MHz -162 MHz; NOTE: Compatible with noninterlaced signals only.
Power Cord Length| 3.0 m (9 ft 10 in)
Cabinet Materials| Molded plastic
Dimensions (W x H x D) PTDW830K/DW830W| 498 x 200 x 556 mm (19 – 19/32 x 7 – 7/8 x 21 – 7/8 inches) (with supplied lens)
Dimensions (W x H x D) PTDW830LK/DW830LW| 498 x 200 x 513 mm (19 – 19/32 x 7 – 7/8 x 20 – 3/16 inches) (without lens)
Weight PT-DW830K/DW830W| Approx. 18.3 kg (40.3 lbs) (with supplied lens)
Weight PT-DW830LK/DW830LW| Approx. 17.6 kg (38.8 lbs) (without lens)
Operation Noise| 40 dB (dual lamp operation, LAMP MODE: NORMAL), 35 dB (dual lamp operation, LAMP
MODE: ECO)
Operating Temperature| 0℃ – 45 ℃ (32℉ – 113 ℉)
Operating Humidity| 10% – 80% (no condensation)
Technology| 1-Chip DLP

Note
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.

1. When the STANDBY MODE is set to ECO, network functions such as power on over the LAN network will not operate, and the serial output terminal cannot be used. Also, only certain commands can be received for external control  sing the serial terminal.
2. Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
3. Only compatible with dot clock frequency of 27 MHz (pixel repetition signal)
4. WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).
5. With legs at shortest position.
6. Average value. May differ depending on models.
7. The operating temperature range is 0 °C to 40 °C (32 °F to 104 °F) when the fan control is set to High Altitude mode (for altitudes from 1,400 m to 2,700 m (4,593 ft to 8,858 ft) above sea level). Also, if the ambient temperature exceeds 40 °C (104 °F) (35 °C (95 °F) in High Altitude mode) when the projector is being used with Lamp Select set to Dual and Lamp Power set to High, the light output may be reduced approximately 20% to protect the projector.
8. Operation range differs depending on environments.

PT- DW 830
https://eu.connect.panasonic.com/gb/en/products/projectors/pt-dw830

References

• PT-DW830 | Panasonic Connect

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>