Langsdom TS03 ClipBuds Wireless Earcuff Earphone User Manual

User Manual
ClipBuds
Wireless Earcuff Earphone

We appreciate you for purchasing the Langsdom ClipBuds Wireless Earcuff Earphone, the following instructions will guide you to use it easily.

Wearing

Put the earphone in your ears, rotate and adjust it to the best angle, be sure to wear comfortably and secure fit.

Accessories

Diagram

Earphone

1. Microphone

2. LED indicator

3. Charging contacts

4. Smart touch

5. Sound hole
   Charging box

6. Charging port

7. LED indicator

Auto On/ Off

1. When the earphone is off, open the charging box and take earphone out, the earphone will power on automatically.
2. When the earphone is on, put the earphone into the charging box, the earphone will power off automatically

Manually On/Off

1. When the earphone is off, long press the earphone touch area about 2 seconds to power on the earphone.
2. When the earphone is on, long press the earphone touch area about 5 seconds to power off the earphone.

Pairing

How to pair
When earphone and phone is within effective distance, open the charging box and take earphone out, the left and right earphone will power on and connect automatically. Turn on phone’s Bluetooth function and enter the search pairing state, select “ClipBuds” device in the Bluetooth list of smart devices to connect.
Auto pairing

1. After powering on, the earphone will automatically search for the other one to reconnect and pair itself with the last connected device within 3 minutes, otherwise power off automatically.
2. When the earphone is disconnected from the device beyond the effective distance, it will automatically reconnect after returning to the effective distance within 1 minute.

Reset the pairing
When the left and right earphones are unpaired and disconnected to the phone, press the left and right earphones’ touch area 4 times and power off to reset successfully, then put the left and right earphones back to the charging box and take out the left and right  earphones to repair.
Touch Control

Music Mode
Play/Pause(L/R) x2
Previous song(L) x3
Next song(R) x3
Call Mode
Answer/Hang up(L/R) x2
Long press 2s(L/R): Reject
Voice Assistant (Siri)(L/R) x4

Charging

Charging the earphone
The earphone’s red light and charging box’s blue light are on charging
The earphone’s red light is off fully charged
The earphone is fully charged about 1.5 hours
Charging the box
The charging box’s red light flashes charging
The charging box’s red light is on fully charged
The charging box is fully charged about 1.5 hours
※ The charging box’s blue light flashes when power is below 15%.
Warning

1. Do not listen for a long time at a high volume to prevent injury to hearing.
2. Do not wear earphone while driving, cycling or walking, otherwise it will easily cause traffic accidents.
3. The earphone only can be charged with DC5V charger, using a fast charger that more than DC5V or charger with DC5V more than 1.5A will cause overheat or fire.
4. Do not expose the earphone to high temperature or expose it to sunlight for a long time.
5. The storage temperature of the earphone is 10°C to 30°C.
6. Please fully charge after a long-term placement, and ensure that it is charged every 3 months.
   ※ It is recommended that new earphone be fully charged before use.

Service

1. Please contact us if any problems, we will provide you professional service.
2. Warranty is only covered by the first year of purchase. Free repair service if the failure is caused by product quality.
3. Please provide the product warranty card and the corresponding order number so that we can better solve the problem for you.

Product Parameters

Model: TS03
FCC ID: 2AZDD-CLIPBUDS
Charging Voltage: DC5V
Battery Capacity: 40mAh*2/400mAh
BT Frequency Range: 2.402-2.480GHz
Audio Frequency: 20Hz-20KHz
Drivers Size: Φ13mm
Impedance: 16Ω±15％
Transmission Range: 10m
Sensitivity: 96dB±3dB
Play Time: About 7 hours
Earphone’s Charging Time: About 1.5 hours

FCC Compliance Notice

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
‐Reorient or relocate the receiving antenna.
‐Increase the separation between the equipment and receiver.
‐Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
‐Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>