TOSHIBA SSA-550A Ultrasound Owner’s Manual

< Action required>

1. Step -1 to -8 are the same as above.
2. Enter “optionchange1” using the keyboard and press [ENTER].
3. Enter “FDD$ON” using the keyboard and press [ENTER].
4. Enter “MOD$OFF” using the keyboard and press [ENTER].
5. Set the Line Command to OFF then, Turn off / on the system, and check the problem.

Nemio Data Back-up & Restore

BACK-UP Operation procedures

• Service function “Main menu”
• [PRESET D..] -> Preset -> Maintenance -> [Shift] and [<] -> password “oimeN” (last “N” capital letter) -> [OK]
• Insert blank & properly formatted MO disk into left MO drive. Write protect must be set to OFF.
• Select Service function “Main menu” -> (in Short-Cut Menu) select “Backup / Restore” -> check command “Backup” -> check the back-up item ;
• Select (put check mark on) “IQ Report” at the bottom OR
• select “All Packages” , Select Drive to MO ( or FD )
• Press [Go], then system will ask to format MO disk, select OK to format and start back-up.
• If MO disk format type does not match with Nemio MO, the system will display error message ;
• “Disk Error Check to see if disk is present”
• Check MO disk format type (FLOPPY TYPE (Super Floppy Type) FAT16) according to the section 7 “MO Format” for the proper format type.
• Smart back-up will also back-up all user data.
• Set Write protect to ON for safety. And mention system identification ( such as customer and system serial number ) on MO disk label.. This is because one MO disk can store the back-up data only for one particular system.

RESTORE Operation procedures

• Insert MO disk which has back-up data stored.
• [PRESET D..] -> Preset -> Maintenance -> [Shift] and [<] -> password “oimeN” (last “N” capital letter) -> [OK]
• Select Service function “Main menu” -> Backup / Restore -> check command “Restore” -> check the back-up item
• select “All Packages. Select Drive to MO ( or FD )
• Press [Go], then system will ask to format MO disk, select OK to format and start back-up.

DMU Data Back-up & Restore

Data backup

1. Using the backup function of the application software
   • Place the test MO in the MO drive and copy the files to the MO.
   • It is possible to use the copy function of the application software installed in the system.
   • Note that if no problems are found in operational checks after finished, it is not necessary to restore the backup files.
   • Data backup procedures – Using the copy function of the application software. Click the Patient List on the toolbar.
   • Select the study to be saved and click the [Send] button. Select “MOD Drive”.
2. Using Windows Explorer
   • If the system application cannot be started up, use Windows Explorer. In this case, also back up the following file.
   • The backup file must be restored together with the data.
   • C:\ Dicomit\db\tpatient.mdb
   • Note that if no problems are found in operational checks after finished, it is not necessary to restore the backup files.
   • Data backup procedures – Using Windows Explorer. Launch Windows Explorer.
   • Copy all of the files in the following directories to the MO.
   • D:\ Images D:\Advanced D:\Measure Copy the following file to the MO. C:\Dicomit\db\tpatient.mdb

System configuration backup
Perform the following procedures to back up the settings of the system. Backup of the system settings. Click [Utilities] on the toolbar of the main menu and select “Configuration Utility”. Click [Service] and enter the utility password [pc-ws]. Place a formatted MO into the MO drive and click [Backup]. If the system application cannot be started up, use Windows Explorer to copy the following files to the MO.

• c:\dicomita\dicomit.cfg
• c:\dicomit\ini\ToFile.cfg
• c:\dicomit\ini\Toshiba.cfg
• c:\dicomit\dtk\dtk32.mdb
• c:\winnt\system32\drivers\etc\Lmhosts
• c:\tomtec\*.ecp (all files with extension “ecp”)
• c:\tomtec\*.dct (all files with extension “dct”)
• Note that if no problems are found in operational checks after finished, it is not necessary to restore the backup files.

RESTORE

1. Restoring the system. Click [Utilities] in the toolbar of the main window, and select Configuration Utility. Click [Service] and enter the utility password “pc-ws” .Insert the backup MO disk in the MO drive and click [Restore]. Select the folder corresponding to “AE Title” of the PC (example: “AE Title_TOSHIBAxxxxxxx”). Click [OK].

Restoring the DB (database)

1. Using the application function
   • When backup was performed using the application function, follow the procedures below to restore the database.
   • Restoring the database – Using the application function. Click the Patient List button on the toolbar.
   • Select “MO Images” in the “Source” selection column. Select the study to be restored and click the [Retrieve] button.
2. Using Windows Explorer

   •   * When Windows Explorer was used for backup because the system application could not be started up, follow the procedures below to restore the database.

   • Restoring the database – Using Windows Explorer. Launch Windows Explorer. Copy all of the files from the
   • MO to the following directories.
   • D:\Images D:\Advanced D:\Measure
   • Copy the “tpatient.mdb” file from the MO to the following directory.
   • C:\Dicomit\db
   • After restoration is completed, start up the application software.
   • Restoring the database – Using Windows Explorer. Launch Windows Explorer.
   • Copy all of the files from the MO to the following directories.
   • D:\Images D:\Advanced D:\Measure
   • Copy the “tpatient.mdb” file from the MO to the following directory
   • C:\Dicomit\db
     After restoration is completed, start up the application software.

Nemio system software re-installation

Back-up User data and un-install Nemio option software before you do the following. See the section 10 Option software installation and section 13 Data back-up and restore.

SOFTWARE INSTALLATION

1. Insert the System Disk in the FD drive.
2. Turn ON the power and hold down the FREEZE switch.
3. When the initial screen is displayed and the message “Detect FREEZE key” is displayed at the bottom of the screen, release the FREEZE switch.
4. The 2D screen is displayed when system software installation is completed. Misalignment between the 2D image and characters may occur after 2D image display. This can be solved by rebooting the system. If the problem persists even after the system is rebooted, go to step (17).
5. Remove the System Disk from the FD drive.
6. Reboot the system.
7. Press [Preset D..] . The Exam Select menu is displayed.
8. Select [Preset] in the Exam Select menu. The Preset screen is displayed.
9. Select [System Configuration] from the Preset screen. The ” System Configuration ” screen is displayed.
10. Press the keys. The Special Configuration screen is displayed.
11. Set the “Line Command” to On and press [OK].
12. When the message “Are you sure” is displayed, press [OK].
13. When the message “Please Power OFF” is displayed, reboot the system.
14. Press the [SET] switch.
15. Press the [Ctrl]+[Alt]+[D] keys simultaneously.
16. When this kit is to be installed in the USA, enter “usaop$on” using the keyboard and press [Enter] key. When this kit is to be installed in countries other than the USA, enter “usaop$off” and press [Enter] key.
17. If the TV format remains abnormal even after the system is rebooted, follow the steps below.
    • (a) For the NTSC TV format, enter “tveia$on” and press [Enter] key.
    • (b) For the PAL TV format, enter “tvpal$on” and press [Enter] key.
    • (c) Reboot the system.
18. Turn OFF the power and disconnect all transducers.
19. Turn ON the power.
20. When the 2D screen is displayed on the system monitor, insert the System Maintenance Disk in the FD drive.
21. Make acoustic power minimum and press [SET] switch.
22. Press the [Ctrl]+[Alt]+[D] keys simultaneously.
23. Enter ” txbfispfd flttbl7″ (the characters other than (7) in this command are alphabetical characters) using the keyboard and press [Enter] key.
24. Following comment is displayed in about one minute. ISP terminated with error 0 Error zero means successfully terminated.
25. Remove the System Maintenance Disk from the FD drive.
26. Set the “Line Command” in the Special Configuration screen to Off and press [OK].
27. When the message “Are you sure” is displayed, press [OK].
28. When the message “Please Power OFF” is displayed, turn OFF the power.
29. Connect transducers.

DATA RECOVERY
Confirm that the data items that were recorded in section 2 ” DATA RECORDING” have not changed. If some settings are to be changed or appear to be incorrect, change or correct them.
CONVERSION OF USER-REGISTERED MEASUREMENT DATA

1. Start the system and press PRESET D. . The Exam Select menu is displayed.
2. Select [Preset] from the Exam Select menu. The Preset screen is displayed.
3. Select [Measure Registration] on the Preset screen. The Measure Registration screen is displayed.
4. If user-registered measurement data exists, an error message is displayed. Press [OK] several times until the error message screen disappears.
   • On this screen, “Error” is displayed in place of the user-registered measurement name.
5. Press the [Shift] and [<] keys. The [Convert] switch is displayed.
   • If the [Convert] switch is grayed out, the following steps need not be performed. Press [Exit] to close the Measure Registration screen.
6. Press the [Convert] switch., press [OK].
7. When conversion is completed,. Press [OK].
8. Confirm that the measurement names that were displayed as “Error” are now displayed correctly.
9. Press [Exit] to close the Measure Registration screen.

DMU Application software re-installation

For Version is V1.1 or later version

• Remove all probes. Remove front cover – only one screw at the upper part of front cover. ( below two points are fixed by “magic tape” tightly ; just pull it.)
• Find mouse and keyboard connectors. Remove internal ones originally connected and connect external mouse and keyboard supplied with the system.
• Turn on the system. Select APPLI switch on Nemio to display DMU screen after boot-up. Set Write protect for MO disk.
• Insert MO disk )(or CD-ROM) into right side MO disk. (left side is also okay, but right one is basically for DMU)
• Select Utility in tool bar – Configuration – (password : pc-ws) – select service – EXIT TO OS. ( or Enter [Ctrl]+[Alt]+[Delete] to start the task manager and terminate the TDICOM10 application)
• Start Windows Explorer, select (CD-ROM or) Removable Disk [E:] (means MO) , and double-click .
• You can find “UpV12” directory (or UpV11). open this directory and find batch file named ;
• UpV11.bat ( or UpV12.bat). Double click this batch file.
• Installation will be started.
• During installation, there will be the message on page 6/6 may appear : saying
• Windows 2000 hotfix setup… [OK] This is the message regarding red-code virus.
• Select OK to continue. Then proceed further software Installation according to the messages.
• The installation will be finished with-in a few seconds.
• Remove the system software disk from the drive. Select DMU application “Nemio” from the start bar.
• After DMU application starts, de-select APPLI switch. Turn off the system. Restart the SSA-550A

For Version V1.0 DMU( will be very rare case)

• Remove all probes. Remove front cover – only one screw at the upper part of front cover. ( below two points are fixed by “magic tape” tightly ; just pull it.)
• Find mouse and keyboard connectors. Remove internal ones originally connected and connect external mouse and keyboard supplied with the system.
• Turn on the system.
• Select APPLI switch on Nemio to display DMU screen after boot-up.
• Set Write protect for MO disk.
• Insert MO disk )(or CD-ROM) into right side MO disk. (left side is also okay, but right one is basically for DMU)
• Select Utility in tool bar – Configuration – (password : pc-ws) – select service – EXIT TO OS. ( or Enter [Ctrl]+[Alt]+[Delete] to start the task manager and terminate the TDICOM10 application)
• Start Windows Explorer, select (CD-ROM or) Removable Disk [E:] (means MO) , and double-click .
• You can find “APP” directory. open APP directory and select all files – copy.. then select C drive, (right click) COPY. ( This means copy all the files / directory under “APP” directory in MO disk to DMU “C” drive.)
• Overwrite all the files and directory.
• Remove the system software disk from the drive.
• Select DMU application “Nemio” from the start bar.
• After DMU application starts, de-select APPLI switch. Turn off the system.
• Restart the SSA-550A

DMU Network settings

Network Settings for UIDM-550A
The UIDM-550A Workstation, or DMU, is a Windows 2000 based system, so the method for making the network settings is slightly different than that used for the PowerView, which is a Windows NT based system.
The following is offered as an aid in navigating the newer system.

1. To get to the Network Settings area, use the same steps as those used on the PowerView. Click on the Hammer on the toolbar, select Configuration, and click on the Service button and enter password pc-ws.
2. This will bring you to the Service Configuration screen. Click on the Network button as before.
3. You will now see the Windows 2000 Network Connection screen.
4. Click on Advanced on the menu bar, and select Network Identification from the drop down menu.
5. You will see the System Properties screen. Click on Properties to rename the DMU to your desired name.
6. On the Identification Changes screen, type in the name selected for your DMU.
7. Click on OK for the name change, and OK for the System Properties.
8. That will bring you back to the Network Connections screen. Double click on Local Area Connection, below Make New Connection.
9. That will bring up the Local Area Connection Properties screen. Select Internet Protocol (TCP/IP) and then click on Properties.
10. That will bring up the Internet Protocol (TCP/IP) Properties screen where you can enter your assigned IP Address.
11. After entering the IP address, click on OK on this screen, and OK on the next screen. You will get a message. asking if you want to restart now. Click on Yes to accept the restart.
12. After the DMU restarts, you can continue with the configuration the same as you do with the PowerView systems; DICOM setup, Install Options, etc.

Note If the system start asking you for LOG-ON password after changing some Network settings, check the next section 18 “DMU LOG-ON password” to remove the LOG-ON message.

DMU LOG-ON password Nemio DMU (UIDM-550A) log-on password
[ TROUBLE ]
DMU ask you for log-on password during boot-up.
[ OUTLINE ]
For DMU password, this password must be “system”. We suppose the registry file was changed by some improper re-works for network settings.
[ SOLUTION ]
The following you can find the solution. This work is to setup Windows auto log-on with default password. So that after trying the following procedures “1)” to “8)”, Windows will not asking you for log-on but it will be automatically log-on.
BE CAREFUL DO NOT ACCESS ANY OTHER REGISTRY FILES EXCEPT THE ONE WE MENTIONED BELOW !! Connect keyboard and mouse to the DMU. Switch on.

1. logon with the “system” password.
2. With the “Window” key on your keyboard go to the “start bar” and select Start –>
3. RUN…. type “regedit”
   • In the path : Mycomputer \ HKEY_LOCAL_MACHINE \ software \ Microsoft \ windowsNT \
   • CurrentVersion \ WinLogOn
   • You will see that the “AutoAdminLogon” is set to “0”
4. Double click on “AutoAdminLogon” and change the value to “1”
5. Then with the mouse go to Edit –> New –> String Value
6. Type “DefaultPassword”
   • Right click on it and select “modify”
   • Type as value “system”
   • Now exit and save the new settings.
7. Shutdown and disconnect your keyboard and mouse and connect the panel and trackball again.
8. Switch back on and the unit is running without asking for Log-on message.

Nemio Reset (without turn off / on)

Nemio can be restarted instead of Power off / on by the following.
Press the combination of ; FREEZE & SELECT (NEXT) & NEW PATIENT switches.

DMU Reset (without turn off / on)

Preparation
External Keyboard External Mouse: Remove rear cover to see DMU PC inside to access PC power switch afterwards.Remove front cover by removing only one screw. ( bottom of front cover is fixed by “magic tape” strongly.) Refer to service manual for those mechanical dis-assembly procedures. At the system front side, you can find DMU PC rear side. So that remove standard Keyboard and Mouse connectors and connect External Keyboard and External Muse to the proper connectors on DMU PC rear. Also prepare MO disk.

Operation procedures-1

• Turn on Nemio.
• After boot-up, select [APPLI] switch.
• Now DMU can be operated by External Keyboard and External mouse.
• Select hummer mark on TOOL BAR. Select Configuration Utility.
• Select [SERVICE] then key-in “pc-ws” as a password to enter Service menu.
• If optional software were installed, un-install those options by INSTALL/UNINSTALL.
• For the procedures for un-installation, you of course need the original optional software key MO (or FD).
• Un-install all optional software accordingly.
• If any important patient data in HDD, we also recommend you back-up those data into MO disks.
• Those patient data will be not deleted by the following process, but as usual ( generally speaking ), it is better back-up those user data into MO disks for safety back-up.

Select [EXIT TO OS]

• The message will appear. Select [OK] to exit to the Windows OS.
• Then move the courser to START, you can find the DMU application software “Nemio” at the top of START bar,
• Select “Nemio” in the START bar, then Nemio DMU application will be re-started.

Operation procedures-2

• If the above, you exit to Windows OS via service menu. But you can also exit to OS by simple way.
• After you go to APPLI, press the keys : [Ctrl] + [Alt] + [Del], then Windows Security screen will appear.
• Select “Task Manager”, Task Manager screen will appear. Select “End Task” to end all the activating Tasks.
• After ending all those Tasks, it will be Windows screen. Then the procedures will be the same as the above.

Total Blockdiagram

Genral Blockdiagram

Power Supply Section

“Power Monitor” function is available in Service menu – Test Tools – Diagnostics [PRESET D..] -> Preset -> Maintenance -> [Shift] and [<] -> password “oimeN” (last “N” capital letter) -> [OK] Service menu items : For the details, refer to 2D730-1511E Service manual [Maintenance Menu Volume]

TOSHIBA CORPORATION MEDICAL SYSTEMS COMPANY ©Toshiba Corporation 2002 all rights reserved Service Note (Basic support information) Service Note ( Basic support information ) Nemio ( model SSA-550A)

References

• 富士通 法人向けパソコン（PC）・タブレット製品情報, ESPRIMO（エスプリモ）, LIFEBOOK（ライフブック）, STYLISTIC（スタイリスティック）, CELSIUS（セルシアス） -FMWORLD.NET（法人）：富士通

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>