Delonghi ECAM35050SB Bean to Cup Espresso and Cappuccino Machine Instructions

Delonghi ECAM35050SB Bean to Cup Espresso and Cappuccino Machine

Product Information

• Product Name: ECAM35X.50 Bean to Cup Espresso and Cappuccino
  Machine

• Manufacturer: Delonghi

• Website: http://ecam35050.delonghi.com/

• Year of Manufacture: 2010

Product Usage Instructions

1. Introduction
   The user manual provides instructions for using the ECAM35X.50 Bean to Cup Espresso and Cappuccino Machine. It also includes troubleshooting and repair information.

2. Description

   • Description of the Appliance: The user manual describes the features and functions of the espresso and cappuccino machine.
   • Description of Control Panel: The user manual explains the different buttons and settings on the control panel of the machine.
   • Description of Accessories: The user manual provides information about the accessories included with the machine.
   • Description of the Milk Container: The user manual explains the features and usage of the milk container.

3. Setting up the Appliance
   The user manual provides instructions for setting up theB ECAM35X.50 Bean to Cup Espresso and Cappuccino Machine.

4. Turning the Appliance On
   The user manual explains how to turn on the machine.

5. Turning the Appliance Off
   The user manual provides instructions for turning off the machine.

6. Setting Water Hardness
   The user manual explains how to set the water hardness for optimal performance.

INTRODUCTION

Thank you for choosing this bean to cup espresso and cappuccino machine.We hope you enjoy using your new appliance. Take a few min- utes to read this Instruction for Use. This will avoid all risks and damage to the appliance.

Letters in brackets
The letters in brackets refer to the legend in the description of the appliance.

Troubleshooting and repairs
In the event of problems, first try and resolve them by reading the information given in the section “22. Troubleshooting” If this does not resolve the problem or you require further in- formation, you should consult customer services by calling the number given on the annexed “Customer Service” sheet. If your country is not among those listed on the sheet, call the number given in the guarantee. If repairs are required, contact De’Longhi customer services only. The addresses are given in the guarantee certificate provided with the machine.

DESCRIPTION

Description of the appliance

• A1. Beans container lid
• A2. Pre-ground coffee funnel lid
• A3. Beans container
• A4. Pre-ground coffee funnel
• A5. Grinding adjustment dial
• A6. Cup shelf
• A7. button: to turn the appliance on and off (standby)
• A8. Hot water connection nozzle
• A9. Coffee spouts (adjustable height)
• A10. Condensate tray
• A11. Coffee grounds container
• A12. Cup tray
• A13. Drip tray water level indicator
• A14. Tray grille
• A15. Drip tray
• A16. Water tank lid
• A17. Water tank
• A18. Water softener filter housing
• A19. Infuser door
• A20. Infuser
• A21. Power cord

Description of control panel

A number of icons on the touch screen have a double function. This is indicated in brackets in the description.

• B1. Indicator light
  • blinking for 5 seconds then permanently alight: jug needs deaning
  • blinking: position the froth adjustment dial on CLEAN / jug cleaning in progress
• B2. alight:
  • blinking: reposition the grounds container (A11)
  • permanently alight: the grounds container needs emptying
• B3. light:
  • blinking: position the water tank (A17)
  • permanently alight: insufficient water in the tank
• B4. Indicator light : general alarm, see section *21. Explanation of lights”)
• B5. Indicator light Id:
  • blinking: descaling in progress
  • permanently alight: descaling required
• B6. Indicator light** :** pre-ground function
• B7. Indicator light : coffee aroma
• B8. Icon : aroma selection
• B9. Icon 2x: to make 2 cups of”espresso*
• B10. Icon : to make “Espresso”
• B11. Icon : to make “Coffee*
• B12. Icon : to make “Cappuccino*
• B13. Icon : to make “Latte macchiato”
• B14.Icon ESC
  • to make “Hot milk”: with milk container in place
  • to make “Hot water”: with hot water spout in place (ESC: press to exit the function in progress)
• B15. Icon OK: to perform a rinse cyde.
  • Ok: press to confirm the function.

Description of the accessories

• C1. Reagent strip (*if provided)
• C2. Pre-ground coffee measure(*if provided)
• C3. Descaler (*if provided)
• C4. Water softener filter (*if provided)
• C5. Cleaning brush (*if provided)
• C6. Hot water spout

Description of the milk container

• D1. Froth adjustment and CLEAN dial
• D2. Milk container lid
• D3. Milk container
• D4. Milk intake tube
• D5. Frothed milk spout (adjustable)

SETTING UP THE APPLIANCE

Please note: The first time you use the appliance, rinse with hot water all removable accessories which may come into contact with water or milk. Possible traces of coffee in the mill are the result of oper- ating tests performed on the appliance before sale, proof of the meticulous care and attention we invest in our  products.You should customise water hardness as soon as possible following the instructions in section “18. Setting water hardness”.

1. Connect the appliance to the mains supply (fig. 1).
2. Remove the water tank (A17), fill to the MAX line with fresh water (fig. 2) then return it to its position (fig. 3);
3. Check that the hot water spout (C6) is connected to the noz- zle (A8) (fig. 4) and place a container (fig. 5) of minimum capacity 200 ml underneath the hot water spout and the coffee spout;
4. The indicator light A (B4) and the OK icon (B15) blink. Press the OK icon B15): the machine will de- liver hot water. The coffee machine is now ready for normal use.

The coffee machine is now ready for normal use.
Please note:

• When using the appliance for the first time, 4- 5 cappuccinos need to be made before it starts to give satisfactory results.
• When making the first 4-5 cappuccinos, it is normal to hear the noise of boiling water. After this, the noise becomes
• To enjoy your coffee even more and improve the performance of your appliance, we recommend installing a water softener filter (C4) as described in section “19. Water softener filter” If your model is not provided with a filter, you can request one from De Longhi customer services.

TURNING THE APPLIANCE ON
Every time the appliance is turned on by pressing the on/off button (A7), it automatically performs a preheat and rinse cycle which cannot be interrupted. The appliance is not ready for use until the cycle has been completed.

Danger of scalding!
During rinsing, a little hot water comes out of the coffee spouts (A9) and is collected in the drip tray (A 15) underneath. Take care to avoid contact with splashes of water.

• To turn the machine on, press the ( ) button (A7) (fig. 6). All of the indicator lights and the icons will shine on the control panel, and all the beverage icons then blink.

The machine proceeds to run a rinse cycle; besides heating the boiler, this serves to circulate hot water around the internal dircuits so that they are warmed up as well. Once the heating cyde has ended, the coffee beverage and OK icons become active and light up; if the milk container (D3)  is in position, the icons indicating the milk beverages will alsobe active.

TURNING THE APPLIANCE OFF
Whenever the machine is turned off after being used to make coffee, it performs an automatic rinse cyde.

Danger of scalding!

• During rinsing, a little hot water flows from the coffee spouts (A9). Take care to avoid contact with splashes of water.
• To turn the appliance off, press the ( ) button (A7) (fig. 6);
• If provided for, the appliance performs a rinse cycle then goes off (stand-by)

Please note:

• If you will not be using the appliance for some time, unplug it from the mains socket: first turn the appliance off by pressing the ( ) button (fig. 6);

SETTING WATER HARDNESS
For instructions on setting water hardness, see section “18. Set- ting water hardness”.

SETTING TEMPERATURE
To change the temperature of the water used for making coffee (low, medium, high), proceed as follows:

1. With the machine off (in standby mode) but still plugged
   into the electrical power supply;

2. Press and hold the icon 2 (B9) until the indicators on the
   touch screen (B) light up;

3. Press the icon (B10);

4. Press the icon again to select the desired temperature :

5. Pressthe oK icon (B15) to confirm (or ESC (B14) to exit without making any change). The lights go off. The appliance returns to “standby” and the temperature is now programmed.

AUTO-OFF
THE time can be changed so that the appliance switches off after being idle for 15 or 30 minutes, or after 1, 2 or 3 hours.

To re-programme Auto-off, proceed as follows:

1. With the machine off (in standby mode) but still plugged into the electrical power supply;
2. Press and hold the icon 2 (B9) until the icons on the touch screen (B) light up;
3. Press the icon (B11);
4. Press the icon again to select the desired time interval:
5. Press the OK icon (B15) to confirm (or ESC (B14) to exit without making any change). The lights go off. The auto-off time is now programmed.,

ENERGY SAVING

Use this function to enable or disable energy saving. This mode is active by default, reducing energy consumption while the ma- chine is on in compliance with current European regulations. To change the setting, proceed as follows:

1. With the machine off (in standby mode) but still plugged into the electrical power supply;
2. Press and hold the icon 2 (B9) until the indicators on the touch screen (B) light up.
3. Press the licon (B13);
4. Press the icon again to enable/disable the  function:
   • function enabled
   • function disabled
5. Pressthe OK icon (B15) to confirm (or ESC (B14) to exit without making any change). The lights go off. The energy saving setting is now programmed.

Please note:
in energy saving mode, a few seconds may elapse before the first coffee is delivered as the appliance must heat up again.

BEEP
This function enables or disables the beep. Proceed as follows:

1. With the machine off (in standby mode) but still plugged into the electrical power supply;
2. Press and hold the icon 2 (B9) until the indicators on the touch screen (B) light up.
3. Press the 2x icon to enable/disable the function:
   • function enabled
   • function disabled
4. Pressthe OK icon (B15) to confirm (or I ESC (B14) to exit without making any change). The lights go off. The beep is now programmed.

DEFAULT VALUES (RESET)
This function resets all settings (temperature, auto-off, water hard- ness, energy saving and all quantity settings are reset to the default values).

1. With the machine off (in standby mode) but still plugged into the electrical power supply;
2. Press and hold the icon 2× (B9) until the indicators on the touch screen (B) light up.
3. Press the icon (B12): the beans (B7) on the touch\ screen will blink;
4. Press the OK icon (B15) to reset the default values (or (B14) to exit without making any change). The lights go off.

The settings and quantities of the beverages have been reset to the default values.

RINSING
Use this function to deliver hot water from the coffee spouts (A9) to clean and heat the appliances internal circuit.
Place a recipient under the coffee and hot water spouts.
Important! Danger of scalding.
Do not leave the appliance unattended while hot water is being delivered.

1. To activate the function, press oK(B15);
2. After a few seconds, hot water is delivered from the coffee spouts, cleaning and heating the appliance’s internal Circuit.
3. To interrupt the function manually, press OK again.

Please note:

• If the appliance is not used for more than 3-4 days, when switched on again, we strongly recommend performing 2/3 rinses before use;
• AFTER cleaning, it is normal for the coffee grounds container (A11) to contain water.

MAKING COFFEE

Adjusting the coffee mill
The coffee mill is set by default to prepare coffee correctly and should not require regulating initially. However, if after the first few attempts it becomes apparent that the coffee is either too weak and not creamy enough, or emerg. es too slowly (drop by drop), this can be corrected by adjusting the grinding adjustment dial (A5) (fig. 7).

Please note:
The grinding adjustment dial must be used only when the coffee mill is in oneration.

If the coffee is delivered too slowly or not at all, turn one click clockwise towards 7. For fuller bodied creamier coffee, turn I one click anticlockwise towards 1 (do not turn more than one click at a time other- wise the coffee could be delivered a drop at a time).
The effect of the adjustment will be noticed only after making a further 2 cups of coffee, at least. If this adjustment does not produce the desired result, turn the dial another click.
Tips for a hotter coffee
To make a hotter coffee, proceed as follows:

• perform a rinse cycle by pressing OK (B15);
• warm the cups with hot water using the hot water function (see section “15. Delivering hot water”);
• increase the coffee temperature (see section “18. Setting water hardness”).

Making coffee using coffee beans

Important! Do not use green, caramelised or candied coffee beans as they could stick to the coffee mill and make it unusable.

1. Fill the beans container (A3) (fig. 8) with coffee beans;
2. Place under the coffee spouts (A19):
   • cup, to make 1 coffee (fig. 9);
   • cuns to make ) coffes
3. Lower the spouts as near as possible to the cup. This makes a creamier coffee (fo. 10):
4. Then select your required coffee:
5. Preparation begins and the indicator corresponding to the selected icon blinks on the touch screen (B).

Please note:

• To make 2 cups of “‘espresso” at the same time:
• Press the icon (B9): the icons corresponding to the beverages available light up, and the 2x icon blinks. Press ° (B10): preparation begins.

Alternatively, proceed as follows:

• Press : preparation begins and the 2 x icon blinks for a few seconds. Press the 2x icon while it is blinking.
• While the machine is making coffee, delivery can be inter- rupted at any moment by pressing the coffee icon. As soon as delivery has ended, to increase the quantity of coffee in the cup, simply press and hold the icon cor- responding to the beverage selected. The selected icon switches to
• fast blink. Once the coffee has been made, the appliance is ready to make the next beverage.

Please note:

• Indicator lights may appear on the control panel (B) during use. Their meaning is given in section “21. Explanation of lights. For hotter coffee, see section “13.2 Tips for a hotter coffee”. If the coffee is delivered a drop at a time, too weak and not creamy enough or too cold, read the tips in section “22. Troubleshooting.
• To customise the beverages according to personal taste, see section “13.6 Customizing aroma and quantity”.

Temporarily varying the coffee aroma
To vary the aroma of the coffee temporarilv, oress (B8):

Please note:

• The variation in aroma is not saved and the next time a beverage is delivered automatically, the appliance selects the default value.
• If a few seconds elapse between temporary customising of the aroma and delivery of the beverage, the aroma returns to the default value.

Preparing coffee with pre-ground coffee
Important!

• Never add pre-ground coffee when the machine is off or it could spread through the inside of the machine and dirty it. This could damage the machine.
• Never use more than 1 level measure (C2) as it could dirty the inside of the coffee machine or block the funnel (A4).

Please note:
When using pre-ground coffee, only one cup can be made at a time.

1. Press the button (B8) repeatedly, until the – indicator light (B6) appears.
2. Make sure the funnel is not blocked, then add one level measure of pre-ground coffee (fig. 111
3. Place a cup under the coffee spouts (A9) (fig. 9);
4. Then select vour required coffee:
5. Preparation begins and the indicator light corresponding to the selected icon blinks on the touch screen B).

Please note:
If “Energy Saving” mode is active, you may have to wait a few seconds before the first coffee is delivered.
Customizing aroma and quantity

The appliance is set by default to make coffee with a standardaroma and quantity (see table in section “13.3 Making coffee using coffee beans*). To customize the coffee, proceed as follows:

1. Place a sufficiently large cup or glass under the coffee spouts (A19);
2. Press (B8) to select the desired aroma (see section “13.4 Temporarily varying the coffee aroma”);
3. Press and hold the icon corresponding to the coffee to be customized: the icon blinks and all the alarm indicator lights also blink;
4. Release the icon. The icon blinks and the appliance starts delivering coffee;
5. As soon as the coffee in the cup reaches the required level, press the coffee icon again. The aroma and quantity of coffee in the cup has now been programmed.

MAKING CAPPUCCINOS AND MILK-BASED COFFEES
Please note:

• To avoid milk with poor froth or large bubbles, always dean the milk container lid (D2) and hot water connection nozzle (A8) as described in sections “14.5 Cleaning the milk container after use”, “16.10 Cleaning the milk container” and “16.11 Cleaning the hot water nozzle”.

Filling and attaching the milk container Remove the lid (D2) (fig. 12);

Please note:

• To avoid milk with poor froth or large bubbles, always dean the milk container lid (D2) and hot water connection nozzle (A8) as described in sections *14.5 Cleaning the milk container after use, “16.10 Cleaning the milk container” and “16.11 Cleaning the hot water nozzle”.

Filling and attaching the milk container

1. Remove the lid (D2) (fig. 12);
2. Fill the milk container (D3) with a sufficient quantity of milk, not exceeding the MAX level marked on the contain- er (fig. 13). Each mark on the side of the container corresponds to 100ml of milk;
   • Please note: For a denser and more evenly distributed froth, always use skimmed or partially skimmed milk at refrigerator temperature (about 5 °C).
   • If”Energy Saving” mode is enabled, you may have to wait a few seconds before the first cappuccino is delivered.
3. Make sure the milk intake tube (D4) is correctly inserted in the bottom of the milk container lid (fig. 14)
4. Place the lid back on the milk container;
5. Remove the hot water spout (C6) from the nozzle (A8) (fig. 15);
6. Attach the container to the connection nozzle and push as far as it will go (fig. 16). The machine emits a beep (if enahled
7. Place a sufficiently large cup under the coffee spouts (A9) and the frothed milk spout (D5). Adjust the length of the milk spout. To move it nearer the cup, simply pull it down- wards (fig. 17).
8. Follow the instructions below for each function.

Adjusting the amount of froth
Turn the froth adjustment dial (D1) to adjust the amount of froth on the milk delivered while making cappuccinos and milk-based coffees (fig. 18 ).

Making milk beverages automatically

1. Fill the milk container (D) and attach it as described above;
2. Select the required beverage:
   • :Cappuccino (B12)
   • Macchiato (B13)
   • Hot Milk (B14)
3. After a few seconds, the appliance starts preparing the selected beverage automatically.
4. Depending on the beverage selected, the appliance delivers one or two ingredients automatically.

Please note:
To interrupt preparation and delivery, if so desired, press the icon relative to any other beverage. Conversely, to interrupt the first step and pass straight on to the second, press the icon of the selected beverage.
• Do not leave the milk container out of the refrigerator for long periods. The warmer the milk (5°C is ideal), the poorer the quality of froth produced.

Customizing milk beverages
To customize milk beverages, proceed as follows:

1. Place a sufficiently large cup or glass under the coffee spouts (A19);
2. Press and hold the icon corresponding to the beverage tobe customized: the icon blinks and all the alarm indicator lights also blink;
3. Release the icon: the icon blinks and the appliance starts delivering the beverage;
4. Once the amount of liquid in the cup is as desired (milk and/or coffee), press the selected icon a second time: the flow will cease. The quantity of the beverage in the cup has now been programmed.

Cleaning the milk container after use
Important! Danger of scalding When cleaning the internal tubes of the milk container (D), a little hot water and steam leak out of the milk spout (D5). Take care to avoid contact with splashes of water. Every time a drink is prepared with milk, the lid of the milk con- tainer (D2) must be cleaned afterwards. Clean as described to eliminate all milk residues (or press (B14) to postpone the cleaning operation until later):

1. Leave the milk container (D) in the machine (it does not have to be emptied);
2. Place a cup or other recipient under the frothed milk spout;
3. Turn the froth adjustment dial (D1) to “CLEAN™ (fig. 19). Cleaning stops automatically;
4. Turn the dial back to one of the froth selections;
5. Remove the milk container and always clean the steam connection nozzle (A8) with a sponge (fig. 20).

Please note!

• To prepare a number of cappuccinos or milk-based coffees, clean the milk container after preparing the last of the beverages: in this instance press ESC (B14) to go back to the main menu.
• The milk container can be kept in the refrigerator.
• In certain cases, the appliance will need to heat up before the container can be cleaned.

DELIVERING HOT WATER
Important! Danger of scalding. Never leave the machine unattended when hot water is being released.

1. Make sure the hot water spout (C6) is attached correctly:
2. Place a container under the water spout (as close as possible to avoid splashes) (fig. 5);
3. Press ESC (B14);
4. The machine delivers about 250 ml of hot water, then de- livery stops automatically. The icon blinks during delivery, To interrupt the flow of hot water from the spout, press (B14)

Please note:
If “Energy Saving” mode is active, there may be a few seconds pause before hot water is delivered.

CLEANING

Cleaning the machine

• The following parts of the machine must be cleaned regularly: the appliance’s internal circuit;
• coffee grounds container (A11);
• drip tray (A15) and condensate tray (A10);
• water tank (A17);
• coffee spouts (A9);
• pre-ground coffee funnel (A4);
• infuser (A20), accessible after opening the infuser door (A19);
• milk container (D);
• hot water connection nozzle (A8);

Important!

• Do not use solvents, abrasive detergents or alcohol to clean the coffee machine. With De’ Longhi superautomatic coffee machines, no chemical products are required for cleaning purposes.
• None of the components of the appliance can be washed in a dishwasher with the exception of the drip tray grille (A14) and milk container (D).
• Do not use metal objects to remove encrustations or coffee deposits as they could scratch metal or plastic surfaces.

Cleaning the internal circuit
If the appliance is not used for more than 3/4 days, before using it again, we strongly recommend switching it on and: running 2/3 rinse cycles by pressing OK (B15); release hot water for a few seconds (section “15. Delivering hot water”).

Please note:
Water may find its way into the grounds container (A11) during the above rinse procedure: this is quite normal.
Cleaning the coffee grounds container
When the indicator light (B2) appears on the touch screen, the container must be emptied and cleaned. The appliance can-  not be used to make coffee again until the grounds container(A11) has been cleaned. Even if the grounds container is not full, the message indicating that it should be emptied will be displayed 72 hours after the first coffee has been prepared (for the 72 hours to be calculated correctly, the machine must never be turned off by unplugging the power cord).
Important! Danger of scalding If you make a number of cappuccinos one after the other, the metal cup tray (A12) becomes hot. Wait for it to cool down be- fore touching it and handle it from the front only.

To clean (with the machine on):

• Remove the drip tray (A15) (fig. 21), empty and dean.
• Empty the grounds container (A11) and clean thoroughly to remove all residues left on the bottom. This can be done using the spatula incorporated into the brush (C5).
• Check the red condensate tray (A10) and empty if necessary;

Important!

• When removing the drip tray, the grounds container must be emptied, even if it contains few grounds.
• If this is not done, when you make the next coffees, the grounds container will fill up more than expected and clog the machine.

Cleaning the drip tray and condensate tray

Important! The drip tray (A15) is fitted with a level indicator (A13) (red) showing the amount of water it contains (fig. 22).

Before the indicator protrudes from the cup tray (A12), the drip tray must be emptied and cleaned, otherwise the water may overflow the edge and damage the appliance, the surface it rests on or the surrounding area.
To remove the drip tray:

1. Remove the drip tray and grounds container (A11) (fig. 21);
2. Remove the cup tray (A12) and drip tray grille (A14), then empty the drip tray and grounds container and wash all components;
3. Check the red condensate tray (A10) and empty if necessary;
4. Replace the drip tray complete with grille and the grounds container.

Cleaning the inside of the machine Danger of electric shock!
Before cleaning internal parts, the machine must be turned off (see section “5. Turning the appliance off”) and unplugged from the mains power supply. Never immerse the machine in water.

1. Check regularly (about once a week) that the inside of the appliance (accessible after removing the drip tray (A15)) is not dirty. If necessary, remove coffee deposits with the brush (C5) and a sponge;
2. Remove all residues with a vacuum cleaner (fig. 23).

Cleaning the water tank

1. Clean the water tank (A17) regularly (about once a month) and whenever the water softener filter (C4) is replaced, using a damp cloth and a little mild washing up liquid;
2. Remove the filter (C4) and rinse under running water;
3. Replace the filter (if installed), fill the tank with fresh water and replace;
4. Release 100 ml of water.

Cleaning the coffee spouts

1. Clean the coffee spouts (A9) regularly with a sponge or cloth (fig. 24A);
2. Check the holes in the coffee spout are not blocked. If necessary, remove coffee deposits with a toothpick (fig. 24B).

Cleaning the pre-ground coffee funnel

1. Check periodically (about once a month) that the pre-ground coffee funnel (A4) is not blocked. If necessary, remove coffee deposits with the brush (CS) supplied.

Cleaning the infuser
The infuser (A20) must be cleaned at least once a month.
Important! The infuser cannot be extracted while the machine is on.

1. Make sure the machine is correctly turned off (see section “5. Turning the appliance off”);
2. Remove the water tank (A17);
3. Open the infuser door (A19) (fig. 25) on the right side of the appliance;
4. Press the two coloured release buttons inwards and at the same time pull the infuser outwards (fig. 26);
5. Soak the infuser in water for about 5 minutes, then rinse under the tap;
   • Important! RINSE WITH WATER ONLY NO DETERGENTS – NO DISHWASHERDo not use detergents when cleaning the infuser, as they could damage it.
6. Use the brush (C5) to remove any coffee residues left in the infuser housing, visible through the infuser door;
7. After cleaning, replace the infuser by sliding it onto theinternal support, then push the PUSH symbol fully in until it clicks into place;
   • Please note: If the infuser is difficult to insert, before insertion, adapt it to the right size by pressing the two levers (fig. 27).
8.  Once inserted, make sure the two coloured buttons have snapped out;
9. Close the infuser door;
10. Put the water tank back.

Cleaning the milk container
Clean the milk container (D) after use, every time that milk is prepared. as described below:

1. Remove the lid (D2);
2. Remove the milk spout (DS) and intake tube (D4) (fig. 28);
3. Turn the froth adjustment dial (D1) anticlockwise to the “INSERT” position (fig. 29) and pull off upwards;
4. In a dishwasher (recommended: Rinse all components and the container with hot running water (at least 40°C), then place them in the top basket of the dishwasher and run a programme at 50°C, e.g. standard ECO. By hand: Rinse all components and the container with hot running water (at least 40°C), then immerse all the components in hot tap water (at least 40°C) with a mild/neutral wash- ing-up liquid for at least 30 minutes. Rinse thoroughly with hot tap water.
5. Rinse inside the froth adjustment dial seat with running water (fiq. 31);
6. Check that the intake tube and milk spout are not clogged with milk residues;
7. Replace the dial (in correspondence to the word “INSERT”), spout and milk intake tube;
8. Place the lid back on the milk container (D3).

Cleaning the hot water nozzle
Each time you prepare milk, dean the connection nozzle (A8) with a sponge to remove milk residues from the gaskets (fig. 20).

DESCALING
Important!

• Before use, read the instructions and the labelling relative to the descaler product, which are indicated on the pack (included with certain models and/or available for purchase from authorized service centres).
• Use De’Longhi descaler only. Using unsuitable descaler and/or performing descaling incorrectly may result in faults not covered by the manufacturer’s guarantee.
• Descaler could damage delicate surfaces. If the product is accidentally soilt dry immediately.

To descale

Descaler| De’Longhi “EcoDecalk” descaler
Container| Recommended capacity: 1.8
Time| ~45min

Descale the machine when the indicator la (B5) lights up on the panel.

To proceed with descaling immediately, if preferred, follow the instructions from point 1. To postpone the descaling procedure until later, press ESC (B14): the indicator (B5) on the touch screen remains alight as a reminder that the appliance needs tobe descaled.
To start the descaling procedure:

1. Take out the water tank (A17), remove the water softener filter (C4) and empty the water from the tank.
2. Pour the descaler into the tank up to level A (corresponding to a 100 ml pack) marked on the inner surface of the tank (fig. 32), then add water (1 litre) up to level B (fig. 33) and put the water tank back.
3. Remove, empty and replace the drip tray (A15) and the grounds container (A11)
4. Place an empty container with a minimum capacity of 1.8 litres under the hot water spout (C6) and coffee spouts (A9)( . 34): Press 19) OK (B15):
   • Important! Danger of scalding Hot water containing acid flows out of the coffee spouts and hot water spout. Take care to avoid contact with splashes of this solution.
5. The descale programme starts and the descaler liquid comes out of the hot water and coffee spouts. A series of rinses is performed automatically to remove all the scale  residues inside the coffee machine. This is the longest phase and may account for more than half the total descaling time. After completing the descaling cycle, the appliance is ready to be rinsed through with clean water.
6. Empty the container used to collect the descaler solution. Remove the water tank from the machine, empty it and rinse under running water, then fill with dean water up to the MAX level (fig 35) and reposition it in the machine.
7. Empty the container used to collect the descaler solution,\ then position it under the coffee spout and the hot water spout (fig. 34);
8. Press OK (B15);
9. Hot water is delivered first from the coffee spouts, then from the hot water spout;
10. When the water in the tank has run out, empty the container used to collect the rinsing water;
11. Take out the water tank and fill with fresh water up to the MAX level.
12. If the water softener filter was removed, replace it in its housing in the water tank, and reposition the tank in the appliance;
13. Empty the container used to collect the descaler solution, then position it under the hot water spout.
14. Press OK (B15).
15. Hot water comes out of the hot water spout;
16. At the end of the second rinse, remove, empty and replace the drip tray (A15) and grounds container (A11).
17. Empty the container used to collect the rinse water; re- move the water tank from the machine, empty it and rinse under running water, then fill with clean water up to the MAX level and reposition it in the machine. The descaling cycle is now complete.

Please note!

• If the descaling cycle is not completed correctly (e.g. power failure or disconnection from power supply), the machine will prompt it to be completed when switched on again.
• WATER may find its way into the grounds container (A11) during the descaling cyde: this is quite normal;
• If the water tank has not been filled to the MAX level, at the end of descaling, the appliance requests a third rinse to quarantee that the descaler solution has been completely eliminated from the machine’s internal circuits. The appliance may request descaling cycles at very short intervals. This is normal and due to the appliance’s advanced control system.
• THE descaling procedure can also be started by pressing and holding the icon (B8).

SETTING WATER HARDNESS
The descaling alert is displayed after a period of time established according to water hardness. The machine is set by default for a hardness level of 4. The ma- chine can also be programmed according to the actual hardness of the local water supply, so that the descaling procedure will be required less frequently.
Measuring water hardness

1. Remove the “TOTAL HARDNESS TEST” reagent strip (C1) from its pack;
2. Immerse the strip completely in a glass of water for about one second;
3. Remove the strip from the water and shake lightly. After about a minute, 1, 2, 3, or 4 red squares will appear, de- pending on the hardness of the water. Each square corresponds to 1 level;

Setting water hardness

1. With the machine off (in standby mode) but still plugged into the electrical power supply;
2. Press and hold the 2x icon (B9) until the indicator lights appear on the touch screen (B);
3. Press the icon (B8);
4. Press the icon again to select the water hardness level;
5. Press the OK icon (B15) to confirm (or ESC (B14)  to exit without making any change). The lights go off. The machine is now reprogrammed with the new water hard- ness setting.

WATER SOFTENER FILTER
To use the filter correctly, follow the instructions below.
Installing the filter

1. Remove the filter (C4) from the packaging. The date indicator disk varies according to the filter provided.
2. Turn the date indicator disk (see fig. 36) until the next two months of use are displayed.

WATER SOFTENER FILTER
To use the filter correctly, follow the instructions below.
Installing the filter

1. Remove the filter (C4) from the packaging. The date indicator disk varies according to the filter provided.
2. Turn the date indicator disk (see fig. 36) until the next two months of use are displayed.
   • Please note: The filter lasts about two months if the appliance is used normally. If the coffee machine is left unused with the filter in- stalled, it will last no longer than 3 weeks.
3. To activate the filter, run tap water through the hole in the filter as shown in fig. 37 until water comes out of the openings at the side for more than a minute;
4. Remove the tank (A17) from the appliance and fill with water;
5. Insert the filter in the water tank and immerse it complete- ly for about ten seconds, sloping it and pressing it lightly to enable the air bubbles to escape (fig. 38).
6. Insert the filter in the filter housing (A18) and press fully home (fig. 39);
7. Close the tank with the lid (A16) (fig. 40), then replace the tank in the machine;
8. Attach the hot water spout (C6). Position a container (of at least 500 ml capacity) under the hot water spout (A20)
9. Press the ESC icon (B14) to deliver hot water.
10. Release at least 500 ml of water, then press ESC again (B14) to stop the flow. The filter is now activated and the coffee machine can be used.

Replacing the filter
After two months (see date indicator) or when the appliance has not been used for 3 weeks, you should replace the filter:

1. Extract the tank (A17) and exhausted filter (C4);
2. Take the new filter out of its pack and proceed as illustrated in points 2 to 10 of the previous section.

The new filter is now activated and the coffee machine can be used.

TECHNICAL DATA

• Voltage: 220-240 V~ 50/60 Hz max. 10A
• Absorbed power: 1450W
• Pressure: 1.5MPa (15 bars)
• Max. water tank capacity: 240×440×360 mm
• Size LxDxH: 1250 mm
• Cord length: 9.5 kg
• Weight: 300 g

Max. beans container capacity:
De’Longhi reserves the right to modify the technical specification and styling of its products at any moment, without com- promising their functionality and quality.
Tips for Energy Saving
To reduce energy consumption, after delivering one or more beverages:

• remove the milk container or the accessories.
• Set auto-off to 15 minutes
• Enable Energy Saving
• Always carry out the descaling cycle when prompted by the machine.

EXPLANATION OF LIGHTS

TROUBLESHOOTING

Below is a list of some of the possible malfunctions. If the problem cannot be resolved as described, contact customer services.

Connect the plug to the power socket.
The coffee is not hot.| The cups were not preheated.| Warm the cups by rinsing them with hot water (Please note: you can use the hot water function).
The internal circuits of the appliance have cooled down because 2/3 minutes have elapsed since the last coffee was made.| Before making coffee, run a rinse cycle to heat the internal circuits, by pressing   OK (B15).
Coffee temperature setting too low.| Set a higher coffee temperature in the menu.
The coffee is weak or not creamy enough.| The coffee is ground too coarsely.| Turn the grinding adjustment dial (A5) one click anticlockwise towards 1 while the coffee mill is in operation (fig. 7). Continue one click at a time until coffee delivery is satisfactory. The effect is only visible after delivering 2 coffees (see section “13.1 Adjusting the coffee mill”).
The coffee is unsuitable.| Use coffee for espresso machines.
Coffee not fresh.| The coffee pack has been opened for too long and has lost its taste.
→
PROBLEM| POSSIBLE CAUSE| REMEDY
---|---|---
The coffee is delivered too slowly or a drop at a time.| The coffee is ground too finely.| Turn the grinding adjustment dial (A5) one click clockwise towards “7” while the coffee mill is in operation (fig. 7). Continue one click at a time until coffee delivery is satisfactory. The effect is only visible after delivering 2 coffees (see section “13.1 Adjusting the coffee mill”).
The appliance will not make coffee| The appliance has detected impurities in its internal circuits.| Wait for the appliance to be ready again and reselect the required beverage. Contact customer services if the problem persists.
Coffee does not come out of one or both spouts.| The coffee spouts (A9) are blocked.| Clean the nozzles with a cloth. Any encrusted deposits can be removed with a toothpick, if necessary.
The infuser (A20) cannot be removed| The appliance has not been turned off correctly| Turn the appliance off by pressing the  button (A7) (fig. 6) (see section “5. Turning the appliance off”).
At the end of descaling, the appliance requests a third rinse| During the two rinse cycles, the water tank has not been filled to the MAX level.| Follow the instructions displayed by the appliance, but first empty the drip tray (A15) to avoid the water overflowing.
The frothed milk has large bubbles| The milk is not cold enough or is not semi-skimmed.| Use skimmed or semi-skimmed milk at refrigerator temperature (about 5°C). If the result is not as you wished, try changing brand of milk.
The froth adjustment dial (D1) is incorrectly adjusted.| Adjust following the instructions in section “14.2 Adjusting the amount of froth”
The milk container lid (D2) or froth adjustment dial (D1) are dirty| Clean the milk container lid and control knob as described in the section “16.10 Cleaning the milk container”.
The hot water connection nozzle (A8) is dirty| Clean the connection nozzle as described in section “16.11 Cleaning the hot water nozzle”
The milk does not come out of the milk spout (D5)| The lid (D2) of the milk container lid is dirty| Clean the milk container lid as described in sec- tion “16.10 Cleaning the milk container”

www.delonghi.com/register. De’Longhi Appliances via Seitz, 47 31100 Treviso, Italy www.delonghi.comwww.101kofemashina.ru.
Instructions videos available at:http://ecam35050.delonghi.com/ .

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>