JAMES ALLEN VXWS30778VNGB Vintage Brass Avery 17 Tall Wall Sconce Instruction Manual

JAMES ALLEN VXWS30778VNGB Vintage Brass Avery 17 Tall Wall Sconce

WARNING: Turn off the main power at circuit breaker before installing fixture.

NOTE:

1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. Read and save these instructions.

Hardware Package (included):

• Mounting Plate Unit (A)

• Mounting Screw (B)

• Wire Connector (C)

• Set screw (D)

Installation Steps

Turn off the power at fuse or circuit box

1. Unscrew the two set screws (D) and remove the mounting plate unit (A) from the backplate.

2. Attach the mounting plate unit (A) to the outlet box by using two mounting screws (B).3. Pull out the source wires from the outlet box. Make wire connections using wire connectors (C) as follows:
   • Connect the hot wire (black insulation) from the fixture to the black wire from the power source.
   • Connect the neutral wire (white insulation) from the fixture to the white wire from the power source.
   • Attach the fixture ground wire (bare wire) to the mounting plate unit (A) with the green ground screw, then connect it to the house ground wire with the wire connector (C). Carefully put all of the wires back into the outlet box.

3. Attach the backplate of the fixture to the mounting plate unit (A) by aligning holes, secure the two set screws (D) from the side hole of the backplate into the hole in the side of the mounting plate unit (A).
   Note: With silicone caulk compound, caulk completely around where the backplate meets with the wall surface to prevent water from seeping into the outlet box.

4. Take a glass panel and gently slide it into the bottom notch of the frame in place, secure it by pressing the two clips on top side of the frame. Repeat with the other glass panels. (See Fig.1 and Fig.2)

5. Install the bulb (not included). Check relamping label at socket area or packaging for maximum wattage allowed.
   Turn on the power at fuse or circuit box

Optional Installation: Disconnect Dusk-to-Dawn Photocell

IMPORTANT:
Compatible with dimmer when photocell is disconnected.

• Requires dimmable bulb and compatible dimmer switch.
  
  

  1. Turn off the power at the fuse or circuit box before starting installation.

  2. Loosen the wire connector connected with the wires from photocell. (See Fig.3)
     Note: Do not remove the photocell to prevent water from seeping into the outlet box.

  3. Take a white pigtail and black pigtail and make wire connections using wire connector (C): (See Fig.4)
     a. The black wire from the fixture to one end of the black pigtail.
     b. The white wire from the fixture to one end of the white pigtail.
     c. The other end of the black pigtail to the black wire from the power source.
     d. The other end of the white pigtail to the white wire from the power source.
     Put all wires back into the backplate of the fixture.
     Turn on the power at fuse or circuit box.

The following parts are available for re-order if damaged or missing.

Spare Parts List:

Dimension

A: 16-314″ B: 6″ C: 7″

5 Year Limited Warranty

In addition:

• Any product with an integrated motion sensor, including all Dualux® and lnstalux® products, is supported by a 5-year warranty for the functionality of the product.
• Any product with integrated LED modules is covered by a 5-year warranty on the LED functionality.

Exclusions: This warranty does not include the failure of products from extreme acts of nature; environmental conditions not suited for the products intended use; operation in temperatures outside of the range specified in the instruction manual; usage with improper power supply, power surges or dips. For coastal locations, some corrosion is considered normal for the environment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>