ESUNSTAR ALK-AF792-V2.0 4G Router WIFI ZOOM IP Camera Instruction Manual

4G router WIFI ZOOM IP Camera
Instruction

How to put SIM card into IP camera

as shown in Figure 1 2,Connect the camera power, please do not plug in the network cable. (If you plug in the network cable, the camera will be connected to the wired network first, 1 and the 4G network will not work).and Please wait 1 minute, the 4G camera will automatically complete the 4G network connection.

How to add camera on smartphone

Download “Camhi” / “Camhipro” ( for IOS and android ) from APP store，open it and click add. Scan the QR code above to enter the download page

http://www.yucvision.com/camhi-en.htm

Install Camhipro mobile APP and add camera

Now 4G camera Configure the connection successfully.

4,4G Router hardware description

Product size：49.038.08.5mm（LWH）Installation method: fixed with holes or directly fixed with bolts Hole size：33.033.0mm（LW）

4.2 Interface Overview

Table 2: Interface and Status Indicator Description

DC12V
2| Work light 1| After the module is turned on and started, it remains on and flashes when there is a terminal connected to WIFI; The power supply is disconnected and the indicator light is off
3| Work light 2| Insert the Nano SIM card, and the module will flash after registering with the network and dialing successfully; The 4G network disconnection indicator light is constantly on
4| SIM card slot| Insert the Nano SIM card for connecting to the network
5| USB interface| Connect to the computer for debugging and data transmission of the module
6| Network interface| Provide wired data transmission for LAN terminals, used to connect computers or other LAN devices
7| GP10+ Serial port| GPIO and serial debugging interface provided to customers
8| reset key| Press and hold the reset button for 5 seconds before releasing, the module returns to factory settings, and the device automatically restarts

Basic system functions

This chapter will introduce the basic functions of AF792, and the overall block diagram of the routing function is as follows
5.1,How to log into 4G router and manage router
A, Use a computer or mobile phone to connect to the WIFI of the 4G camera, Use a computer to search for the WIFI signal of the camera. The WIFI name is the WIFI signal starting with MIFI-X, as shown in Figure 3. Select this WIFI signal and enter the connection password: 1234567890.
Click the connect button, the computer will automatically connect to the camera via WIFI. As shown in Figure 4, the WIFI connection is successful.
B, Open the browser, enter the login address of the 4G router in the address bar of the browser:
192.168.100.1, enter the login user: admin, login password: admin, as shown in Figure 5.
If the system is displayed in Chinese, please change the language to English, as shown in Figure 5.2 UI Introduction The device supports webUI function. After successfully connecting the device to a computer or mobile phone, enter 192.168.100.1 in the browser address, enter the password admin, and then click to confirm login; There is a language selection in the upper right corner, which defaults to Chinese and supports English.

After logging in, you can make a series of settings for the router.

1. Home page: Display device connection status, signal strength, operator, card status, WiFi access count, IP address, software version, etc.
2. Network page: mainly for network settings, including settings for external network connections and wireless internal networks
3. Advanced settings page: including routing, firewall, firmware upgrade, restart,factory reset, etc

5.3 Soft restart function
Support web based restart routers; The restart time is about 40 seconds, and after 40 seconds, the device fully starts successfully. 5.4 Restore Factory Settings Function
Support web based restoration of factory settings. The module can also be restored to factory parameters by pressing the Reload button (hardware reset button).
Method: Press and hold for 5 seconds to release, and the router will automatically restore its factory parameter settings and restart

.contact information
EsunStar Technology Co., Ltd.
Address: B505-2, Zerun Center, No. 4088 Banxuegang Avenue, Bantian Street, Longgang District, Shenzhen,
Guangdong, China,518129
Contact: Qi quan
Email:service@esunstar.net
Skype:hkcctv2008@outlook.com
WeChat: esunstar

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>