CANDY CLG64SGX 4 Burner Gas Hob User Manual
- June 13, 2024
- Candy
Table of Contents
**CANDY CLG64SGX 4 Burner Gas Hob User Manual
**
SAFETY INSTURUCTIONS
We recommend you keep the instructions for installation and use for later
reference, and before installing the hob, note its serial number in case you
need to get help from the after sales service. Connect a plug to the supply
cable that is able to bear the voltage, current and load indicated on the tag
and having the earth contact. The socket must be suitable for the load
indicated on the tag and must be having the earth contact connected and in
operation. The earth conductor is yellow-green in color. This operation should
be carried out by a suitably qualified professional. In case of WARNING:
the appliance and its accessible parts become hot during use. Care should be
taken to avoid touching heating elements. Children under 8 years of age must
be kept away from the appliance unless they are continuously supervised.
WARNING: use only hob guards designed by the Manufacturer of the cooking
appliance or indicated by the Manufacturer of the appliance in the
instructions for use as suitable or hob guards incorporated in the appliance.
The use of inappropriate guards can cause accidents
WARNING: danger of fire: do not store items on the cooking surfaces.
If present do not to stare into halogen lamp hob elements.
WARNING: unattended cooking on a hob with fat or oil can be dangerous and
may result in fire. NEVER try to extinguish a fire with water, but switch off
the appliance and then cover flame e.g. with a lid or a fire blanket.
WARNING: if the surface is cracked, do not touch the glass and switch off
the appliance to avoid the possibility of electric shock.
This appliance can be used by children aged from 8 years and above and people
with reduced physical, sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
Children should be supervised to ensure that they do not play with the
appliance. Cleaning and user maintenance shall not be made by children without
supervision.
CAUTION: the cooking process must be supervised. A short term cooking
process has to be supervised continuously.
It is strongly recommended to keep children away from the cooking zones while
they are in operation or when they are switched off, so long as the residual
heat indicator is on, in order to prevent the risks of serious burns.
This appliance is not intended to be operated by means of an external timer or
separate remote control system.
Connect a plug to the supply cable that is able to bear the voltage, current
and load indicated on the tag and having the earth contact. The socket must be
suitable for the load indicated on the tag and must be having the earth
contact connected and in operation. The earth conductor is yellow-green in
color. This operation should be carried out by a suitably qualified
professional. In case of incompatibility between the socket and the appliance
plug, ask a qualified electrician to substitute the socket with another
suitable type.
The plug and the socket must be conformed to the current norms of the
installation country.
Connection to the power source can also be made by placing an omnipolar
breaker between the appliance and the power source that can bear the maximum
connected load and that is in line with current legislation.
The yellow-green earth cable should not be interrupted by the breaker. The
socket or omnipolar breaker used for the connection should be easily
accessible when the appliance is installed.
The disconnection may be achieved by having the plug accessible or by
incorporating a switch in the fixed wiring in accordance with the wiring
rules.
If the supply cord is damaged, it must be replaced by Manufacturer, its
service agent or similarly qualified people in order to avoid a hazard. The
earth conductor (yellow-green) must be longer than 10 mm on the terminal block
side. The internal conductors section should be appropriate to the power
absorbed by the hob (indicated on the tag). The type of power cable must be
HO5V2V2-F.
Do not put metallic objects such as knives, forks,
spoons or lids on the hob. They could heat up.
Aluminum foil and plastic pans must not be placed on heating zones.
After every use, some cleaning of the hob is necessary to prevent the build-up of dirt and grease. If left, this is recooked when the hob is used and burns giving off smoke and unpleasant smells, not to mention the risks of fire propagation.
Never use a steam or high pressure spray to clean the appliance.
Do not touch the heat zones during operation or for a while after use.
Never cook food directly on the glass ceramic hob.
Always use the appropriate cookware .Always place the pan in the center of the
unit that you are cooking on
Do not place anything on control panel.
Do not use the hob as a working surface.
Do not use the surface as a cutting board.
Do not store heavy items above the hob. If they drop onto the hob, they may
cause damage.
Do not use the hob for storage of any items.
Do not slide cookware across the hob.
No additional operation/setting is required in order to operate the appliance
at the rated frequencies
1. INSTRUCTIONS FOR THE INSTALLER
INSTALLING A DOMESTIC APPLIANCE CAN BE A COMPLICATED OPERATION WHICH IF NOT
CARRIED OUT CORRECTLY, CAN SERIOUSLY AFFECT CONSUMER SAFETY. IT IS FOR THIS
REASON THAT THE TASK SHOULD BE UNDERTAKEN BY A PROFESSIONALLY QUALIFIED PERSON
WHO WILL CARRY IT OUT IN ACCORDANCE WITH THE TECHNICAL REGULATIONS IN FORCE.
IN THE EVENT THAT THIS ADVICE IS IGNORED AND THE INSTALLATION IS CARRIED OUT
BY AN UNQUALIFIED PERSON, THE MANUFACTURER DECLINES ALL RESPONSIBILITY
FOR ANY TECHNICAL FAILURE OF THE PRODUCT WHETHER OR NOT IT RESULTS IN DAMAGE
TO GOODS OR INJURY TO INDIVIDUALS.
1.1 BUILDING IN
The hob may be installed in any worktop which is heat resistant to a
temperature of 100°C, and has a thickness of 25-45 mm. The dimensions of the
insert to be cut out of the worktop are in shown in Figure 2.
When there is an accessible space between the built-in hob and the cavity
below, a dividing wall made of insulating material should be inserted (wood or
a similar material) (Figure 3).
If the hob is fitted next to a cabinet on either side, the distance between
the cut out and the cabinet must be at least 15cm; while the distance between
the cut out and the rear wall must be at least 7cm.
The distance between the hob and any other unit or appliance above it (e.g. An
extractor hood) must be no less than 70 cm (Figure 4).
Metal objects in the drawer may reach high temperatures due to air
recirculation. It is therefore recommended to use an intermediate wood
panel.
Important – The diagram in figure 1
shows how the sealant should be applied.
The Hob unit is fitted by attaching the Fixing Clamps supplied, using the
holes at the base of the unit.
If a hob of 60 cm is fitted above an oven which is not equipped with fan
cooling system it is recommended that openings are created within the built in
furniture to ensure correct air circulation.
The size of these openings must be at least 300 cm2 and placed as shown in
Figure 5.
When a 60 cm hob or a 75 cm hob is fitted over a built in oven, the latter
Must be fan cooled.
1.2. SUITABLE LOCATION
This appliance must be installed in accordance with the regulations in force
and only used in a well ventilated space. Read the instructions before
installing or using this appliance.
A gas-powered cooking appliance produces heat and humidity in the area in
which it is installed. For this reason you should ensure good ventilation
either by keeping all natural air passages open or by installing an extractor
hood with an exhaust flue. Intensive and prolonged use of the appliance may
require extra ventilation, such as the opening of a window or an increase in
speed of the electric fan, if you have one.
If a hood can not be installed, an electric fan should be fitted to an
outside wall or window to ensure that there is adequate ventilation.
The electric fan should be able to carry out a complete change of air in the
kitchen 3-5 times every hour. The installer should follow the relevant
national standards.
2. ELECTRICAL CONNECTION (FOR U.K. ONLY)
Warning – this appliance must be earthed
This appliance is designed for domestic use only. Connection to the main
supply must be made by a competant electrician, ensuring that all current
regulations concerning such installations are observed.
The appliance must only be connected to a suitably rated spur point, a 3 pin
13 amp plug/socket is not suitable. A double pole switch must be provided and
the circuit must have appropriate fuse protection.
Further details of the power requirement of the individual product will be
found in the users’ instruction and on the appliance rating plate. In the case
of built-in product you are advised, should you wish to use a longer cable
than the one supplied, that a suitably rated heat resistant type must be used.
The wiring must be connected to the mains supply as follows:
CONNECT TO SPUR TERMINAL
Green & Yellow Wire Earth Connection
Blue Wire Neutral Connection
Brown Wire Live Connection
Note: We do not advocate the use of earth leakage devices with electric
cooking appliances installed to spur points because of the «nuisance tripping»
which may occur. You are again reminded that the appliance must be correctly
earthed, the manufacturer declines any responsibility for any event occurring
as a result of incorrect electrical installation.
2.1. ELECTRICAL CONNECTION
Check the data on the rating plate, located on the outside of the unit, to
ensure that the supply and input voltage are suitable.
Before connection, check the earthing system.
By Law, this appliance must be earthed. If this regulation is not complied
with, the Manufacturer will not be responsible for any damage caused to
persons or property. If a plug is not already attached, fit a plug appropriate
to the load indicated on the rating plate. The earth wire is coloured
yellow/green. The plug should always be accessible. Where the Hob is connected
direct to the electricity supply, a circuit breaker must be fitted.
If the power supply cord is damaged this is to be replaced by a qualified
engineer so as to prevent any potential risk.
The earth wire ( green and yellow coloured ) must be at least 10 mm longer
than the live and neutral wires.
The section of the cable used must be of the correct size in relation to the
absorbed power of the hob.
Please check rating plate for the power details and ensure that the power
supply cord is of the type 3×0.75 mm² H05 V2V2-F.
Mains Supply | LIVE | L | Brown Wire | Power Cable |
---|---|---|---|---|
EARTH | Green/Yellow Wire | |||
NEUTRAL | N | Blue Wire |
If an appliance is not fitted with a supply cord and a plug, or with other
means for disconnection from the supply mains having a contact separation in
all poles that provide full disconnection under overvoltage category III
conditions, the instructions shall state that means for disconnection must be
incorporated in the fixed wiring in accordance with the wiring rules.
2.2. GAS CONNECTION
These instructions are for qualified personnel, installation of equipment
must be in line with the relevant national standard. (For
U.K. only: by law the gas installation\commissioning must be carried
out by a “Gas Safe” installer)
All work must be carried out with the electricity supply disconnected.
The rating plate on the hob shows the type of gas with which it is designed to
be used. Connection to the mains gas supply or gas cylinder should be carried
out after having checked that it is regulated for the type of gas with which
it will be supplied. If it is not correctly regulated see the instructions in
the following paragraphs to change gas setting.
For liquid gas (cylinder gas) use pressure regulators which comply with the
relevant national standards.
Use only pipes,washers and sealing washers which comply with the relevant
national standards.
For some models a conic link is furnished to outfit for the installation in
the countries where this type of link is obligatory; in picture 8
it is pointed out how to recognize the different types of links (CY =
cylindrical, CO = conic). In every case the cylindrical part of the link has
to be connected to the hob.
When connecting the hob to the gas supply via use offlexible hoses please
ensure that the maximum distance covered by the hose does not exceed 2 metres.
The flexible tube shall be fitted in such a way that it cannot come into
contact with a moveable part of the housing unit (e.g. a drawer) and does not
pass through any space where it may become crushed/ kinked or damaged in any
way.
To prevent any potential damage to the hob please carry out the installation following this sequence **(picture 6):
**
-
As illustrated, assemble parts in sequence:
A: 1/2 Male Adaptor Cylindirical
B: 1/2 Seal
C: 1/2 Female Gas Adaptor Conical-Cylindirical or Cylindirical- Cylindirical -
Tighten the joints with the spanner, remembering to twist the pipes into position.
-
Attach fitting C to mains gas supply using rigid copper pipe or flexible steel pipe.
IMPORTANT: carry out a final check for leaks on the pipe connections
using a soapy solution. NEVER USE A FLAME.
Also, make sure that the flexible pipe cannot come into contact with a moving
part of the cabinet (eg. adrawer) and that it is not situated where it could
be damaged.
Warning: If gas can be smelt in the vicinity of this appliance turn off the gas supply to the appliance and call the engineer directly. Do not search for a leak with a naked flame.
2.3. ADAPTING THE HOB TO DIFFERENT TYPES OF GAS
To adapt the Hob for use with different types of gas, carry out the following instructions:
-
•Remove the grids and burners
-
Insert on hexagonal spanner (7 mm) into the burner support (Figure 7)
-
Unscrew the injector and replace it with one suitable for the gas to be used (see gas type table)
2.4. REGULATING THE MINIMUM FLAME
After lighting the burners, turn the control knob to the minimum setting
and then remove the knob (this can easily be removed by applying gentle
pressure).
Using a small «Terminal» type screwdriver the regulating screw can be adjusted
as in Figure 9.
Turning the screw clockwise reduces the gas flow, whilst turning it
anticlockwise increases the flow – Use this adjustment to obtain a flame of
approximately 3 to 4 mm in length and then replace the control knob.
When the gas supply available is LPG – the screw to set the idle flame must be
turned (clockwise) to the end stop.
When you have carried out the new gas regulation, replace the old gas rating
plate on your appliance with one (supplied with hob) suitable for the type of
gas for which it has been regulated.
3. USE OF HOB – USER INSTRUCTIONS
This appliance must only be used for the purpose for which it is intended, domestic cooking, and any other use will be considered improper and could therefore be dangerous. The Manufacturer will not be responsible for any damage or loss resulting from improper use.
Before using burner, be sure, grid perimeters center the burner as below
figure.
If you are using Cast Iron Grids; underneath the grid, position of it is
stated. Be sure for the exact grid is used in correct position.
3.1. USING THE GAS BURNER
To ignite the burners, place a lighted taper close to the burner, press in
and turn the control knob anti-clockwise.
If the burners have not been used for a couple of days, wait for a few seconds
before lighting the burner, this will allow any air present in the pipes to
escape.
For appliances fitted with electronic ignition carry out the following:
- Push in and turn the knob anticlockwise to the ignition symbol.
- İgnite the burner by pressing the sparker button.
For hobs fitted with automatic ignition simply push in and turn the knob to
the ignition symbol.
The ignition system will continue to generate sparks as long as the control
knob is being pressed.
If the burner has not ignited within 5 seconds, turn the knob to the 0
position and repeat the operation.
For models fitted with a safety tap (which cuts-off the flow of gas if the
flame is accidentally extinguished) the burners are ignited and described
above, but care must be taken.
Prior to switching on the gas hob ensure that the burners and burner caps are
correctly placed within their position.
Warning: If there is no electricity on appliance, to ignite the burner a lighter should be used;
- Push in and turn the knob anti-clockwise to the ignition symbol,
- While pushing in the button ignite the burner by using a lighter and keep button pushed in 5 seconds after ignition.
GENERAL ADVISE
For best results, use cooking vessels with a flat surface. The size of the
surface should match the gas burner side as follows. Table A.
Burner Type| Ø pan/pot (cm)| Power (kW)| G20/20 mbar
(methane)| G30/28-30 mbar (LPG)
---|---|---|---|---
AUX Auxiliary| 10 – 18| 1,00| 95 l/h| 73 g/h
SR Semi Rapid| 12 – 22| 1,75| 167 l/h| 127 g/h
R Rapid| 16 – 26| 2,70| 257 l/h| 196 g/h
UR Ultrarapid| 16 – 26| 3,50| 334 l/h| 255 g/h
DC 4 kW MONO| 16 – 26| 4,00| 381 l/h| 291 g/h
For smaller containers the gas burner should be regulated so that the flame
does not overlap the base of the pan. Vessels with a concave or convex base
should not be used. WARNING: If a flame is accidentally extinguished, turn
the knob to the off position and do not attempt to re-ignite if for at least 1
minute.
If over the years the gas taps become stiff to turn it is necessary to
lubricate them. Such operation must be carried out only by qualified Service
Engineers.
4. MAINTENANCE AND CLEANING
Before cleaning the hob, ensure the appliance has cooled down. Remove the plug from the socket or (if connected directly) switch off the electricity supply.
Cleaning and user maintenance shall not be made by children without
supervision.Never use abrasives, corrosive detergents, bleaching agents or
acids. Avoid any acid or alkaline substances (lemon, juice, vinegar
etc.) on the enamelled, varnished or stainless steel sections.When cleaning
the enamelled, varnished or chrome sections, use warm soapy water or a non
caustic detergent. For stainless steel use an appropriate cleaning
solution.The burners can be cleaned with soapy water. To restore their
original shine, use a household stainless steel cleaner. After cleaning, dry
the burners and replace.
It is important the Burners are replaced correctly
Chromed grids and burners
Chromed grids and burners have a tendency to discolour with use. This does not
jeopardize the functionality of the hob.
Our After Sales Service Centre can provide spare parts if required.
5. AFTERCARE
Before calling out a Service Engineer please check the following:
- that the plug is correctly inserted and fused;
- that the gas supply is not faulty.
6. PROTECTION OF THE ENVIRONMENT
This appliance is marked according to the European directive 2012/19/EU on
Waste Electrical and Electronic Equipment (WEEE). WEEE contains both polluting
substances (which can cause negative consequences for the environment) and
basic components (which can be re-used). It is important to have WEEE
subjected to specific treatments, in order to remove and dispose properly all
pollutants, and recover and recycle all materials.
Individuals can play an important role in ensuring that WEEE does not become
an environmental issue; it is essential to follow some basic rules:
- WEEE shall not be treated as household waste.
- WEEE shall be handed over to the relevant collection points managed by the municipality or by registered companies. In many countries, for large WEEE, home collection could be present.
- When you buy a new appliance, the old one may be returned to the retailer who has to collect it free of charge on a one-to-one basis, as long as the equipment is of equivalent type and has the same functions as the supplied equipment.
Declaration of compliance: This equipment, in the parts intended to come into contact with food, complies with the regulations laid down in EEC directives 89/109.
The appliance complies with European Directive 2009/142/EC (GAD) and starting from 21/04/2018 with Gas Appliances Regulation 2016/426 (GAR).
By placing the mark on this product, we are confirming compliance to all relevant European safety, health and environmental requirements which are applicable in legislation for this product.
The Manufacturer will not be responsible for any inaccuracy resulting from
printing or transcript errors contained in this brochure. We reserve the right
to carry out modifications to products as required, including the interests of
consumption, without prejudice to the characteristics relating to safety or
function.
“Vald only for Cyprus”
Table 1
| | | | | |
---|---|---|---|---|---|---
Burner Plate| 4 Gas| 4 Gas| 5 Gas| 5 Gas| 5 Gas| 3 Gas
Burner| Aux/SR/R/DC 4 Mono| Aux/2SR/R| UR/2R/SR/AUX| DC/2R/SR/AUX|
DC/R/2SR/AUX| Aux/R/DC 4 Mono
Type| UH60MF| UH60MF| UH75MF| UH75MF| UH75MF| UH60MF
FFD| YES| YES| YES| YES| YES| YES
Aux 1kW| 1| 1| 1| 1| 1| 1
Sr 1,75 kW| 1| 2| 1| 1| 2| –
R 2,7 kW| 1| 1| 2| 2| 1| 1
UR 3,5 kW| –| –| 1| –| –| –
Dc 4 kW Mono| 1| –| –| 1| 1| 1
Nominal Heat Input| 9,45 kW| 7,2 kW| 11,65 kW| 12,15 kW| 11,2 kW| 7,7 kW
G20/20 mbar| 900 l/h| 686 l/h| 1110 l/h| 1158 l/h| 1067 l/h| 734 l/h
G30/28-30 mbar| 688 g/h| 524 g/h| 848 g/h| 884 g/h| 815 g/h| 560 g/h
Installation Class| 3| 3| 3| 3| 3| 3
Voltage V/Frequency Hz| 220-240 V/ 50-60 Hz| 220-240 V/ 50-60 Hz| 220-240 V/
50-60 Hz| 220-240 V/ 50-60 Hz| 220-240 V/ 50-60 Hz| 220-240 V/ 50-60 Hz
Electrical Input Power| 1| 1| 1| 1| 1| 1
Electric Ignition| YES| YES| YES| YES| YES| YES
Product Dimension| 595×510| 595×510| 745×510| 745×510| 745×510| 595×510
This appliance has been designed for non-professional, i.e. domestic, use.
| Gas Type| G20| G20| G25.1| G25.3| G30| G30| G30
---|---|---|---|---|---|---|---|---
Gas Pressure| 20 mbar| 25 mbar| 25 mbar| 25 mbar| 29 mbar| 37 mbar| 50 mbar
Burners| Max (kW)| Min (kW)| Injector NG| Injector NG| Injector NG| Injector
NG| Injector LPG| Injector LPG| Injector LPG
| | | Max – Min| Max – Min| Max – Min| Max – Min| Max – Min| Max – Min| Max –
Min
Aux| 1| 0,3| 72X(1Kw-0,3Kw)| 70X(1Kw-0,3Kw)| 74F1(1Kw-0,3Kw)| 72F1(1Kw-0,3Kw)|
50(1Kw-0,3Kw)| 46(1Kw-0,34Kw)| 43H2(1Kw-0,39Kw)
Sr| 1,75| 0,44| 97Z(1.75Kw-0.44Kw)| 91Z(1.75Kw-0.44Kw)| 98Y(1.75Kw-0.44Kw)|
102F3(1.75Kw-0.44Kw)| 65(1.75Kw-0.44Kw)| 61(1.75Kw-0.51Kw)| 58M(1.75Kw-0.58Kw)
R| 2,7| 0,75| 109y(2.7Kw-0.75Kw)| 110F3(2.7Kw-0.75Kw)| 120F2(2.7Kw-0.75Kw)|
115F2(2.7Kw-0.75Kw)| 80(2.7Kw-0.75Kw)| 78(2.7Kw-0.83Kw)| 73S(2.7Kw-0.96Kw)
UR| 3,5| 1,00| 140T2P(3.5Kw-1Kw)| 130(3.5Kw-1Kw)| 141T2(3.5Kw-1Kw)| 143T2(3
.5Kw-1Kw)| 93(3.5Kw-1Kw)| 93(3.SKw-1.4Kw)| 83(3.SKw-1.2Kw)
Dc 4 kW Mono| 4| 1,8| 151H3(4Kw-1.8Kw)| 145H3(4Kw-1.8Kw)| 150F3(4Kw-1.8Kw)|
146F3(4Kw-1.8Kw)| 100(4Kw-1.8Kw)| 94(4Kw-2.2Kw)| 78F4(4Kw-2.1Kw)
Gas Categories| 112E+3+| II2HS3B/P| 112H3B/P
---|---|---|---
G20 20 mbar| G20 20 mbar| G20 20 mbar
G30/31 28-30/37 mbar| G30 28-30mbar| G30/31 30/30 mbar
| G31 37 mbar|
Countries| _ BE,FR| CY,CZ,GB,GR,IE,IT,PT,SI, ES,TR,CH| BG,
HR,DK,EE,FI,LV,LT,NO,RO,SK,SE,CZ,SI,TR
Gas Categories| II2H3B/P| II2EKSB/P| II2EKB/P| II2E3B/P| 112E3B/P
---|---|---|---|---|---
G20 20 mbar| G25.3 25 mbar| G20 25mbar| G20 20 mbar| G20 20 mbar
G30/3150/50 mbar| G20 20 mbar| G2.1 25mbar| G30/31 37/37 mbar| G30/3150
mbar
| G30/31 30/30 mbar| G30/3130/30 mbar| |
Countries| AT,CH,DE| NL| HU| PL| DE
Efficiency Decleration 2016/426
``UH6OMF 4kW DIAMOND (L1)| **
UH6OMF – BIG REAR (L3, L5)| UH6OMF – BIG FRONT (L2)|
UH6OMF – 3 GAS (L4)
---|---|---|---
SINGLE BURNER EFFICENCY| SINGLE BURNER EFFICENCY| SINGLE BURNER EFFICENCY|
SINGLE BURNER EFFICENCY
AUX| SR| R| DC| AUX| SR| R| DC| AUX| SR| R| DC| AUX| R| DC
| 57,9 %| 54,3 %| 57,6 %| | 60 %| 55,9 %| 54,3 %| | 60 %| 55,9 %| 54,3 %| |
57,6 %| 55,9 %
MEDIUM %56,6| MEDIUM %56,7| MEDIUM %56,7| MEDIUM %56,8
UH75MF UR – CENTRAL (L6)|
UH75MF 4kW – CENTRAL (L7)|
UH75MF 4kW – LATERAL (L8)
SINGLE BURNER EFFICENCY| SINGLE BURNER EFFICENCY| SINGLE BURNER EFFICENCY
AUX| SR| R| R| UR| AUX| SR| R| R| DC| AUX| SR| SR| R| DC
–| 57,1 %| 59,4 %| 57,6 %| 57,6 %| | 60 %| 59,4 %| 59,4 %| 55,7 %| | 60 %| 60
%| 59,4 %| 57,6 %
MEDIUM %57,9| MEDIUM %58,7| MEDIUM %59,3**
The manufacturer will not be responsible for any inaccuracy resulting from
printing or transcript errors contained in this brochure. We reserve the right
to carry out modifications to products as required, including the interests of
con sumption, without prejudice to the characteristics relating to safety or
function.