ifan IF9010 3 In 1 Portable Aircon Air Conditioner User Guide
- June 13, 2024
- ifan
Table of Contents
iFAN 3IN1 PORTABLE AIRCON AIR
CONDITIONER / FAN / DEHUMIDIFIER
IF9010
Parts & Descriptions
LIST OF COMPONENTS
1. Control Panel
2. Air Outlet Louvre
3. Front Housing
4. Base Plate| 5. Top Cover
6. Decorative Box
7. Side Plate
8. Rear Housing
9. Caster
---|---
Exhaust Pipe Assembly
10. EVA Filter
11. Continuous Drainage Hole
12. Air Vent
13. Wrapping Post
14. Con Filter
15. Drainage Hole
INSTALLATION GUIDE
-
INSTALLATION
Warning: before using the portable air conditioner, keep it upright for at least 2 hours. When moving the appliance, ensure that it is kept upright on a horizontal and dry surface.
1.1 Screw the Exhaust Pipe Assembly (exhaust fitting end) into the exhaust port on the rear panel (Fig. 1).
1.2 Half open the window, and mount the Window Sealing Plate Assembly to the window in either horizontal (Fig. 2) or vertical (Fig. 3) directions.
To do so, you may have pull various components of the Window Sealing Plate Assembly open to adjust their opening distance to bring both ends of the assembly into contact with the window frame1.3 Place the Main Body with installed Exhaust Pipe Assembly and fittings before the window, and the distance between the body and walls or other objects shall be least 50 cm (Fig.4). -
Elongate the Exhaust Pipe. Snap the flat end of the Exhaust Pipe joints into the hole of the Window Sealing Plate Assembly into place.
The Exhaust Pipe cannot be distorted nor subject to substantial turning angle (greater than 45 °). Keep the ventilation of the Exhaust Pipe unlocked. (Fig.5 & Fig.6).
Note: The length of the Exhaust Pipe shall be between 280 ~ 1500 mm, and this length is based on the specifications of the air conditioner DO NOT use extension tubes or replace it with other different hoses, or this may cause a malfunction. Exhaust Pipe must be unblocked; otherwise it may cause overheating.
HOW TO USE
REMOTE CONTROL PANEL
①| TIMER| When appliance is ON, press the TIMER key to exit. When
appliance is OFF, press the TIMER key to input.
Press the Timer key ® Symbol flashes ® Press UP or DOWN key to set Timer
(adjusted UP by one hour or Down by one hour, from 1 – 24 hours)
---|---|---
②| WIND SPEED SELECTION| When in FAN or COOL Mode (see 5), press key to
toggle between HIGH or LOW wind speed.
When in DEHUMIDIFY Mode, pressing the key does not work as it is set to the
LOW wind speed mode permanently.
③| UP / DOWN| Adjusts the Temperature or Timer settings.
④| SLEEP| In COOL mode, pressing the SLEEP key turns on Energy saving
operation. Does not work in DEHUMIDIFY or FAN modes.
⑤| FAN MODE| Press to toggle between
FAN ® DEHUMIDIFY ® COOL modes.
⑥| WATER FULL| The lamp will light and buzzer will sound for several
seconds to indicate that the Water Pan inside the appliance is full.
POWER| To turn the appliance ON and OFF.
SAFETY FUNCTIONS
-
Frost Protection Function
In COOL, DEHUMIDIFY or SLEEP mode, if the temperature of the exhaust pipe is too low, the appliance will automatically enter protection status; if the temperature of the exhaust pipe rises to a certain temperature, it automatically reverts to normal operation. -
Automatic Defrosting
The appliance has Automatic Defrosting function. -
Protection Function of the Compressor
To increase the service life of the compressor, it has a 3-minute delay booting protection function after the compressor is turned off. -
Overflow Protection Function
When water in the Water Pan exceeds the warning level, the appliance will automatically sound an alarm, and the “FULL” indicator light will flash. The appliance will stop operating. Follow the instructions below.
After the water is emptied, the appliance will automatically return to the original state.
HOW TO DRAIN AND STORE
-
Manual Drainage
a. Turn the wall switch OFF and unplug the power cable from the wall socket.
b. Move the ② Drainage Pipe connecting the appliance to a toilet or other drainage area to empty the water. You may have to carefully move the appliance, as well.
c. Unscrew the ① Drainage Plug from the Drainage Hole. Water will automatically flow out of the Water Pan. During drainage, the body of the appliance can be tilted slightly backwards
d. Re-attach the ① Drainage Plug securely. Restart the appliance immediately. Otherwise, condensate water of the appliance will flow to the floor. -
Storage instructions (after Manual Drainage)
a. Repeat steps 1 (a) – (d). However, restart the appliance immediately in COOL mode with LOW Wind Speed. Only switch OFF the appliance when the ② Drainage Pipe becomes dry.
b. Turn the wall switch OFF and unplug the power cable from the wall socket. Wrap the power cable around the Wrapping Post.
c. Remove the Exhaust Pipe. Cover the appliance and the Exhaust Pipe in separate plastic bags. Put them in a dry place, keep it out of the reach of children and take dust control measures.
d. Remove the battery of the Remote Control. -
Continuous Drainage (optional – only applicable to DEHUMIDIFY mode)
a. Turn the wall switch OFF and unplug the power cable from the wall socket.
b. Unplug the ③ Rubber Stopper from the Continuous Drainage Hole.
c. Set the ④ Water Pipe into the water outlet, and its other end into a bucket. Water will flow into the bucket.
Warnings
ATTENTION :
Read this booklet carefully as it contains important instructions for a safe
installation, use and maintenance.
Important instructions to be kept for future reference.
The following basic precautions should always be followed when using
electrical appliances:
-
Read all instructions before using the appliance. The Appliance
-
This appliance must be used only for the purpose it was expressly designed; any use NOT complying with the instructions contained in the manual is considered inappropriate and dangerous. The manufacturer is NOT responsible for possible damages caused by the inappropriate and/or unreasonable use.
-
The installation/assembly of the appliance will be made in accordance with the indications of the manufacturer. A wrong procedure may cause damages to persons, animals or objects, for which the manufacturer cannot be considered responsible.
-
When drainage pipes are installed, ensure that the drainage pipes are properly connected, and are not distorted or bended.
-
Before use, check the integrity of the appliance and power cable. DO NOT operate the appliance when its Compressor is damaged. In case you are not sure, contact a qualified person. If the power cable is damaged, it must be replaced by the manufacturer or its service agent, or a qualified technician in order to avoid a shock hazard.
-
Before powering the appliance make sure the rating (voltage and frequency) corresponding to the grid and the socket is suitable for the plug of the appliance, and that the wall socket is properly grounded. This appliance is fitted with an earth wire for extra safety.
-
Avoid the use of adapters and/or extension cables; if their use is absolutely necessary, use only materials in compliance with the current safety regulations and according to the electrical parameters of the adapters.
-
The appliance must NOT be switched on using external timers and/or other remote control appliances which are not specified in this manual.
-
Only use original components & accessories provided by the manufacturer. Any non-original component or accessory NOT recommended by the manufacturer may cause injuries to persons or damage to the appliance.
-
The packing materials (plastic bags, expanded polystyrene, etc.) must be kept out of the reach of children or disabled persons since they represent potential sources of danger.
Location -
This appliance is NOT suitable to be used or stored near heat sources (open flame, ovens, heaters, stoves, etc.) and/or in an explosive environment (in the presence of flammable substances such as gas, vapours, mist or dust, in atmospheric conditions when, after ignition, the combustion is spread in the air). Items containing these substances should never be placed in the appliance, and never be used to clean the appliance in order to avert the risk of fire or explosion.
-
The appliance should NOT be placed on a surface, or in the vicinity of objects, which can be damaged by heat or moisture, such as carpets or plastics. There should be at least 50 cm of free space from the back, left & right sides and at least 20 cm from the top of the appliance to allow adequate air circulation. DO NOT put things on top of the appliance. DO NOT locate multiple portable socket outlets or power supplies at the bottom or rear of the appliance. Never use the appliance near curtains or textiles. If the appliance is operated on wooden furniture, use a protective pad to prevent damage to delicate finishes.
-
Place the appliance at a proper distance from the objects or surrounding walls making sure that its functioning will NOT cause accidental damages.
-
Avoid placing the power cable on abrasive or sharp surfaces or in positions where it can be damaged easily. Avoid placing heavy objects on the cable. The cable must NOT be placed under carpets, or covered with throw rugs, runners or similar. Arrange the cable away from the high traffic area, and where it will NOT be tripped over. DO NOT pull or carry the appliance by the cable.
-
DO NOT operate the appliance next to an open window while it is raining, or use it in the bathroom or other humid environments. Rainwater splashing onto the appliance may cause an electric shock.
-
DO NOT use or store the appliance outdoors. Store and use the appliance only indoors, or in any case, protected from weathering such as rain, direct radiation of the sun and dust.
Operation -
If you are using the appliance for the first time, you should:
a. Clean the exterior parts of the appliance thoroughly with warm water & detergent with a non-abrasive sponge and wipe dry. DO NOT use metal scouring pads. Make sure that the Compressor DOES NOT come into contact with water.
b. Check that the Front Grilles, Air Inlet & Air Outlet are NOT damaged.
c. Place and use the appliance on a horizontal, stable and dry surface. When moving the appliance, make sure that it is in an upright position. Damage may occur if the appliance is placed on an incline or decline.
d. To turn ON : Insert the plug of the power cable directly into the wall socket and switch ON. Ensure that the plug fits tightly into the socket.
e. Press the POWER Button on the Control Panel or the Remote Control once to turn the appliance ON or OFF.
f. Press the FAN MODE Button on the Control Panel or the Remote Control to select between FAN ® DEHUMIDIFY ® COOL modes.
g. Press the WIND SPEED SELECTION Button on the Control Panel or the Remote Control to toggle between HIGH or LOW wind speed. When in DEHUMIDIFY Mode, pressing the key does not work as it is set to the LOW wind speed mode permanently.
h. Press the UP / DOWN Buttons on the Control Panel or the Remote Control to make adjustments to the temperature or timer.
i. Make sure to remove any label or protective sheet which may prevent its proper functioning.
DO NOT:
• cover the appliance during functioning;
• obstruct totally nor partially the Air Inlet & Air Outlet;
• insert objects or body parts (including clothing and hair) through the Air Inlet / Air Outlet to avoid personal injury or damage to the appliance when in operation;
• use insecticide sprays, aromatherapy oils or other flammable substances near the appliance;
• push the buttons on the Control Panel or Remote Control too forcefully;
• use any of the following agents as a cleaner: gasoline, thinner, or benzene;
• leave the appliance unsupervised during operation. -
During operation, DO NOT touch the appliance with wet body parts, and it is recommended to have between you and the standing surface, an isolating element (for example, wearing shoes with rubber soles).
-
DO NOT soak the appliance (especially the Compressor) in water or other liquids, wash it under the tap, or let any liquid flow into the internal casing of the appliance (especially the Control Panel) to prevent electric shock. In case of accidental fall in water, DO NOT try to take it out, but first switch the appliance off. 1
-
Switch the appliance OFF before unplugging the appliance. Plug and unplug the power cable firmly holding it with dry hands. Always unplug the power cable before emptying the appliance; to avoid overheating; if it is NOT used for a long period and before storing, cleaning or performing any maintenance operation. Prior to the latter, leave to cool for at least 30 minutes.
-
In case of malfunction or anomaly during the functioning, switch the appliance off immediately, turn off the power and check the cause of the anomaly, if possible, with the support of a qualified person.
-
If smoke is observed coming out of the appliance, switch the appliance off immediately.
-
This appliance is NOT intended for commercial use but to be used in households and similar applications, such as:
• Staff kitchen areas in shops, offices and other working environments;
• By clients in dormitories, hotels, motels and other residential environments;
• Bed and breakfast type environments. -
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall NOT play with the appliance. Cleaning and user maintenance shall NOT be made by children unless they are older than 8 and supervised. Keep the appliance and its cable out of reach of children less than 8 years old.
-
Save these instructions.
HOW TO CLEAN
Warning: The appliance is fully assembled. DO NOT operate the appliance with any of its parts disassembled. The entire assembled unit works as a single appliance. The appliance must only operate in the upright position. Any other position will be hazardous.
-
Turn the wall switch OFF and unplug the power cable from the wall socket.
-
Clean the surface
Clean with surface of appliance with a wet soft cloth. Don’t use chemicals, such as benzene, alcohol, gasoline, etc.; otherwise, the surface of the appliance will be damaged. -
Clean the filter screen
If the filter screen is clogged with dust, and the effectiveness of the appliance is reduced, clean the filter screen once every two weeks. -
Clean the upper filter screen frame
Clasp the wedging block of the EVA filter screen frame with hands. Force down from the outside to remove the EVA filter screen frame. Unscrew four screws fixing the EVA filter screen and the Rear Housing to remove the EVA filter screen (as shown in the figure below).
Put the EVA filter screen into warm water with neutral detergent (about 40°C/ 104°F) and dry it in the shade after rinsing clean.
PROBLEM SOLVING
Fault symptom | Cause analysis | Troubleshooting |
---|---|---|
The appliance does not respond when any of the buttons are pressed. | The Power | |
Cable could be damaged. | Please stop use and contact customer service. |
AC Fuse could be damaged or the circuit stops functioning to prevent
overload.| Replace the Fuse or restart the unit. If problems persist, please
stop use and contact customer service.
Remote Control or Control Panel could be damaged.| Contact customer service to
replace the Remote Control or to repair the Control Panel.
Remote Control batteries have run out.| Replace the Remote Control batteries.
The overflow indicator displays “FULL”.| Drain the water from the Water Pan
(refer to section on “How to Drain”).
The ambient temperature is too low or too high.| Use the appliance between 7 –
35 °C ℃ (44 – 95 °F).
In COOL mode, the room temperature is lower than the set temperature.|
Decrease the set temperature.
In DEHUMIDIFY mode, the ambient temperature is low.| Place the appliance in a
room with an ambient temperature greater than 17 °C (62 °F).
No air flows out of the appliance while the appliance is operating.| The
Compressor could be damaged.| Please stop use and contact customer service.
The wiring within the Compressor or appliance could have loosened.| Please
stop use and contact customer service.
Fault symptom| Cause analysis| Troubleshooting
---|---|---
The appliance functions, but the air coming out is not cool enough.| ****
There is direct sunlight.| Shift the location of the appliance or close the
curtains.
Doors or windows are open or keep being opened and closed; there are a lot of
people in the same room; or in cooling mode, there are other sources of heat.|
Close doors and windows, or, switch off other sources of heat.
The Filter Screen is clogged with dust or dirt.| Clean or replace the Filter
Screen.
The Air Inlet or Air Outlet is blocked.| Clear the obstructions.
Compressor does not work.| Overheat protection activated.| Wait for 3 minutes
until the temperature is lowered, and then restart the appliance.
The appliance makes a lot of noise.| The appliance is not placed on a flat
surface.| Put the air conditioning on a flat and hard place (to reduce noise).
The Remote Control does not work.| The distance between the appliance and the
Remote Control is too far.| Move the Remote Control closer to the appliance,
and point the Remote Control directly in the direction of the receiver.
The Remote Control is not aligned with the direction of the remote control
receiver.
The AA batteries are dead.| Replace with fresh AA batteries.
Displays ‘E1’.| The Pipe Temperature Sensor is abnormal.| Check the Pipe
Temperature Sensor and related circuitry.
Displays ‘E2’.| The Room Temperature Sensor is abnormal.| Check the Room
Temperature Sensor and related circuitry.
ENVIRONMENTAL TIP
This appliance, along with all other electronic appliances, should, when it is
no longer capable of functioning, be disposed with the least possible
environmental damage according to the local regulations in your area. In most
cases you can discard the appliance at your local recycling centre.
DISPOSAL: Do not dispose this appliance as unsorted municipal waste.
Collection of such waste separately for special treatment is necessary.
SPECIFICATION
MODEL | IF9010 |
---|---|
RATED VOLTAGE | 220 – 240 V ~50 – 60 Hz |
POWER | 1130 W |
COOLING CAPACITY | 10000 BTU |
AIR FLOW VOLUME | 350 m 3 per hour |
DIMENSIONS | 368 x 358 x 713 mm |
WEIGHT | 27 kg (gross) / 24 kg (nets) |
WARRANTY
Warranty Conditions
- This warranty provides against defective materials and manufacturing faults throughout for two years from the date of purchase of the appliance.
- This warranty also does not cover normal wear and tear, replacement of consumable materials and accessories, and the cost of maintenance of the appliance.
- This warranty does not cover the repair or replacement of part/s damaged by misuse, accidents, negligence, alterations, or modifications in any way, or repairs done by any repair organization without the prior consent of Power Pac Electrical Pate Ltd.
- Repair and service are to be performed at: 5 Changi South Lane #03-01 Singapore 486045. A transport fee will be charged for personal doorstep service.
- The original purchaser of the appliance must furnish proof of purchase to our Service Centre with the email or number as registered during submission of warranty when this appliance is sent for repair/service. Failure to do so may delay the receipt of said repair/service by the customer.
- Under no circumstances whatsoever shall the serial number be erased, defaced or altered by the customer and/or his representatives, or the dealer and/or his agents. Failure to ensure this shall invalidate the warranty.
- This warranty is deemed to be void if the defect is cause by the attack of household pests, fire, lightning, natural disasters, pollution, abnormal voltage or the usage of generators.
- This warranty is valid in Singapore only.
- This warranty will be honored subject to the customer’s registration of the warranty inclusive of original invoice or valid purchase receipt. Failure to present these documents will result in denial of service. However, if the customer still requests that the defective appliance be repaired, PowerPact Electrical Pate Ltd may, at its discretion, repair the appliance but impose a labor charge, as well as the costs of the replacement parts, to be borne solely by the customer.
- Please refer to the attached picture for the location of one of our appliance’s serial number, as an example.
Please complete the on-line registration warranty form available on our
website. There is no further requirement to send us any hard copy as part of
our efforts to save the environment.
In accordance with the terms and conditions of this limited warranty as stated
above, Power Pac Electrical Pate Ltd, at its expense shall provide free
services for the appliance within the warranty period from its date of
purchase from our Authorised dealers.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>