Woldoclean 91dAEM1Fd1L Instant Cyanoacrylate Adhesive Liquid Glue For Universal Instructions

INSTRUCTIONS SUPER
GLUE & FILLER

Preparation

Adhesion point
Roughen all adhesion points (sandpaper, file, etc.) to achieve the best possible adhesion.
Make sure that the splices are dry and free of grease,rust, dust and adhesive residue. Acetone works well forcleaning. Air 5 minutes after cleaning. Our tip: Placebaking paper under the area to be glued. This preventsunwanted sticking.

Glue
Open the top part of the fastener. Then cut open the dosing tip. Keep away dirt from the glue tip as it can clog it. Tip After use, wipe the tip clean with a piece of paper to avoid clogging.
Filler
Unscrew the top part of the filler. Then cut open the dosing tip.

Material test

ow to test the suitability for the material „plastic“

1. Scatter a small amount of granules (about 1mm high) onto the surface of the material to be bonded.
2. Put a drop of glue on the granules and wait 1 minute.
3. If you press the „adhesive seam“ with your finger, use little force If you have a material that cannot be bonded without pre-treatment, you can remove it. Roughening with sandpaper can help you even bond these materials together! Can‘t you do the „adhesive seam“ with your finger or only with a large one Remove force, you can stick this item permanently.

Material science

All listed examples are based on empirical values. Therefore, test the adhesive beforehand for suitability of the material, as there may be isolated exceptions!

Suitable materials
Aluminum (ideal for minor repairs), glass, rubber, wood, plastic (except PE and PP) metal & leather, tarpaulins, porcelain, stone, polyester, etc
Unsuitable materials
Felt, masonry, cardboard, styrofoam, Teflon, silicone and plastics that contain wax such as PP and PE

Troubleshooting

If the „glue“ breaks, connection with the base material is not possible (smooth surface is created on the underside of the „glue“).
There is a film of dirt, oil or dust on the splice (thorough basic cleaning or subsequent cleaning with acetone required).
Materials that are difficult to bond. In most cases, roughening the adhesive surface can help.
If the „adhesive seam“ breaks, it is a case of overstressing (too much force applied). It usually helps if you increase the adhesive surface. To do this, several layers of the „adhesive seam“ are applied one on top of the other (2 to 4 layers). glued. The following applies: the larger  the adhesive surface, the more stable and stronger the adhesive bond!

Repairing fractures, cracks and fissures

1. Preparation
   See above

2. Granules
   Apply the granules directly to the area to be repaired. The powder height should not be more than 2mm. There will be no chemical reaction caused by the granules alone.

3. Glue
   Drip the glue onto the granules until the granules completely saturated with the adhesive. Caution: The granulate reacts immediately with the adhesive! A new orientation is no longer possible. There is a chemical reaction and heat. The more you repeat this procedure (apply granules and soak with glue), the more stable the connection will be. Tip: Apply the „adhesive seam“ to the front and back!

4. Curing
   After just a few minutes, you can sand and paint the „adhesive seam“. The final strength may vary depending on the material.

Restoring broken small parts

1. Preparation
   See above

2. Granules
   Pour the granules directly onto the area to be glued. Granula- te height should not be more than 2mm here either. The more granulate is applied to the base material, the more stable your mount will be.

3. Glue
   Drip the glue onto the granules until the granules completely saturated with the adhesive. Caution: The granulate reacts immediately with the adhesive!

4. Curing
   After just a few minutes you can sand and varnish the „glued seam“. This is how you bring the workpiece into the desired shape.

Filling of holes/ missing material

1. Formwork
   To prevent the granules from trickling through, mask the exposed sides with masking tape.

2. Granules
   Sprinkle the granules in the hole to be filled (no higher than 2mm).

3. Glue
   Drip the glue onto the granules until the granules completely saturated with the adhesive. Caution: The granulate reacts immediately with the adhesive! A new orientation is no longer possible. There is a chemical reaction and heat. The more you repeat this procedure (apply granules and soak with glue), the more stable the connection willbe.

4. Curing
   Depending on the filling level, you can remove the adhesive tape after approx. 2 to 10 minutes and process the material, e.g. by drilling, thread cutting, painting and grinding etc.

Gluing without granules

1. Preparation
   See above

2.  Dosing
   Apply a thin layer to one of the sides to be bonded.

3. Contact Pressure
   The liquid adhesive is only hardened by contact pressure. A correction is possible without pressure for a short time.

4. Drying
   Allow the adhesive to sit unstressed for a few minutes to achie- ve full adhesion. For surfaces such as porcelain, metal, stone, tiles, etc., hardening can take several hours (max. 24 hours). The final strength can vary depending on the material

FAQ – Frequently Asked Questions

When do I use the granules?

The granules are used where the adhesive power of the SuperGlue adhesive alone is no longer sufficient (in the case of broken brackets, etc.). The „glued seam“ provides additional reinforcement of the breaking points and adhesions, which should remain flexible. For large-area and precisely fitting adhesions, the adhesive is used alone (without the granulate), e.g. for jewellery, shoe soles, tarpaulins and porcelain cups etc.

What is the relationship between granulate and adhesive?

The ratio of the adhesive to the granules is 1:2. Important: The granules must be completely covered with adhesive (slight color changes of the granules occur when soaking). Make sure that the powder height is never more than 2mm (otherwise the glue can no longer fully cover the powder).

What is the order of application?

First apply the granules and then the adhesive. In the case of a vertical repair (the granules would escape due to gravity) the adhesive is applied first and then the granules.

Can the glued area be removed again?

The hardened „glued seam“ can only be loosened or removed by destroying it.

How long does it take for the „glue“ to dry?

The hardening of the „glued seam“ takes only a few minutes and can be machined, sanded, drilled and painted over after 24 hours.

What to do if glue gets on the skin device?

The adhesive residue can be removed with skin cream, oil or nail polish remover. Sticky fingers can be loosened with twisting movements and cooking oil The remaining adhesive residue can be removed with a fingernail. Tip: cream your hands before use. Attention: Adhesive and granules cause burns on the skin!

bSecurity note

Cyanoacrylate

Danger! Do not inhale fumes! Sticks within seconds skin and eyelids together! Must not be in the hands of children arrive!

Wear suitable protective gloves and goggles. Ventilate work rooms well! Do not inhale Glue ! In case of skin contact immediately  clean with soapy water and then cream with skin cream. In case of eye contact rinse the eyes immediately with a suitable eyewash liquid and rinse immediately see a doctor.

Safety instructions granulate

Hazard designation omitted, WoldoClean-SuperFiller not subject to labeling according to GefStoffV. Keep out of the reach of children, danger of swallowing! Do not inhale the vapors produced when reacting with cyanoacrylate wear protective gloves and goggles, ventilate work rooms well! Danger: Chemical reaction of both substances, heat is generated.In case of eye contact, rinse immediately  with water and consult a doctor. Liability: There will be no liability for damage, improper use and handling of WoldoClean products. Also applies to resale to third parties!

Storage and mount

Store the adhesive and granules upright, cool (below 5°C, e.g. refrigerator/freezer) and dry. This guarantees a shelf life of up to 1 to 2 years.
Our tip
Place both bottles in an empty storage jar, which you can seal airtight with the lid. Please note that the adhesive must be brought to room temperature before use!

Properties

Of the cured chemical „2C glue“

Chemical resistant
(gasoline, diesel etc.)| Ye s
---|---
Temperature resistance| – 45°C to +115°C
UV and water resistant| Ye s
Tensile strength| Rubber (NBR) 83 – 100N/cm
2
Tensile shear strength| Steel 10-22N/mm
2

WoldoClean® by Woldoshop GmbH
Oststrasse 64 – 70a . 22844 . Germany
Norderstedt . Phone +494064667723
E-Mailinfo@woldo-clean.de
www.woldo-clean.de

References

• Reinigung Service Gesundheit - Willkommen bei CLEAN Excellence GmbH
• plentyMarkets on-demand eCommerce Solution

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>