XARALYN Trivero 70 Electric Fireplace Instruction Manual
- June 12, 2024
- Xaralyn
Table of Contents
Manual Electric Fireplace
Version 170720
XARALYN Trivero 70 Electric Fireplace
Important safeguards
Please read these instructions carefully before using the appliance, and alwang the safe use of the appliance. Close supervision is necessary to prevent children from using the appliance as a toy.
Please read these instructions carefully before using the appliance.
- Check that your mains voltage corresponds to that stated on the rating plate of the appliance.
- Do not leave the heater unattended during operation and keep children away.
- From time to time check the appliance for damages. Never use the appliance if cord or appliance Shows any signs of damage. In that case, repairs should be made by a competent qualified electrician°. Should the cord be damaged, it must be replaced by a competent qualified electrician° in order to avoid all danger.
- Only use the appliance for domestic purposes and in the way indicated in these instructions.
- Never immerse the appliance in water or any other liquid for any reason whatsoever. When cleaning the appliance, refer to the instructions in the paragraph “Cleaning and maintenance” because water penetration through the openings can be very dangerous for your appliance.
- Never use the appliance near hot surfaces.
- Before cleaning, replacing a bulb or when you do not use the appliance, always unplug the appliance from the power supply. Do not attempt to remove the plug from the wall socket with wet hands.
- Never use the appliance outside and always place it in a dry environment.
- Never use accessories that are not recommended by the producer. They could constitute a danger to the user and risk to damage the appliance.
- Never move the appliance by pulling the cord. Make sure the cord cannot get caught in any way. Do not wind the cord around the appliance and do not bend it.
- No responsibility is accepted if damage results from improper use, or if these instructions are not complied with.
- Stand the appliance on a stable surface so that it cannot fall.
- Do not place the appliance under a power socket. The power socket must not be in the hot airflow of the appliance.
- Always position the heater in such a way that inflammable materials (such as curtains) cannot be ignited. Ensure at all times that the unit is placed solidly on its base/feet. Make sure that the air inlet and outlet openings are not blocked.
- To avoid any risk of fire, do not cover the heater (e.g. with clothes).
- The heater should only be operated at a minimum distance of 1 meter from any wall (except the wall against which it is mounted), piece of furniture or other object and combustibles.
- Warning: Do not operate the heater near baths, showers, washbasins, swimmingpools or any other water container. It must be impossible to reach the commands of your appliance when you are in contact with water.
- The temperature of the housing and the grids may be very high when the appliance is in use. Avoid contact with the skin.
- Do not allow the power cord to touch any hot part of the appliance.
- Never use the appliance near inflammable or explosive materials.
- Do not insert any objects through the grille or into the interior of the appliance.
- Do not use double adapters or other appliances to connect with heater. (*) Competent qualified electrician: after-sales department of the producer or importer or any person who is qualified, approved and competent to perform this kind of repairs in order to avoid all danger. In’case of need you should return the appliance to this electrician.
Getting started
- Remove the appliance from the box.
- Remove any packaging from the product.
- Place the packaging inside the box and store in a dry place.
- Mount the fireplace. Then plug the power cord into a 230-volt earthed socket.
Contents of carton
- Fireplace.
- Remote control.
- Instruction Manual.
Operation
The fireplace can be controlled with the panel on the unit or with the included remote control.
Main Switch
TheMainSwitchislocatedonthefireplace.Turntheswitchto“I”toconnectpowerandturnthe switch to “O” to cut the power. There will be chiming sound when turning to “I”.
Power on/off
Push the button once (icon will be light up) to turn on power for all functions.
Then touch the button once more to turn all functions off.
Flame intensity
Push the button once to level up/down the flame intensity. Push the button
with the ‘+’ to level up the flame intensity. Push the button with the ” to
level down the flame intensity. If there is only one button, push till desired
flame intensity is reached.
Heat settings fireplace with one button
This fireplace consist of a fan forced electric heater with two heat settings.
Push the button once to activate the heater at low level. Push the button once
more to active the heater at high level. When set in high level, push the
button once more to deactivate the heater.
Heat settings fireplace with two buttons
This fireplace consist of a fan forced electric heater with two heat
settings. Touch the small button once to activate the heater at low level.
Push the button once more to deactivate the heater.
**Push the bigger heating button once to active the heater at high level.
When set in high level, touch the button once more to deactivate the heater.
Note : The fan will continue to run for a short time and turn off
automatically after the heater is turned off.
Tinier settings (Varese, Trivero 130, 180 & 240)** C8,.
Some fireplaces are equipped with a timer ranging from lhr to 9hrs (IH,
2H…9H shown in display). Touch the button once for every lhr increasement.
Fireplace will shut down after set time. Do not leave heater unattended.
Glow effect (Trivero 130, 180 & 240)
Touch the button once to turn on/off the glow effect.
Temperature settings / thermostat control (Trivero 70, 90, 130, 180 & 240)
Adjuststhetemperature set point to your in dividual requirements.Once the desired set temperature is reached the heater will turn off. The heater will cycle on and off to maintain the desired set temperature.
Temperature control
Temperature control This knob controls the thermostat that turns the heat on and off to maintain the desired temperature. Turn the knob to the desired setting. The heat will turn on and off automatically to maintain the set temperature. Note: If the room temperature is above the thermostat setting, the heater will not turn on.
Safety cut-off
-
- This appliance is fitted with a safety cut-off which will operate if the fireplace heater overheats (e.g. due to blocked air vents). For safety reasons, the fireplace heater will NOT automatically reset.
-
To reset the appliance, disconnect the appliance from the mains supply for at least 15 minutes. Reconnect the supply to the mains and switch on the appliance.
Cleaning Warning: The unit must be unplugged from the power supply prior to any maintenance or cleaning in order to reduce the risk of electric shock or fire.
General cleaning instructions -
The housing may be wiped with a slightly damp, lint-free cloth. Do not use any abrasive scouring pad or steel wool.
-
Do not use detergents or cleaning products.
-
If necessary, dust particles accumulated in the air outlet openings may be removed with a vacuum cleaner.
Protection of the environment – directive 2002/96/EC
In order to preserve our environment and protect human health, the waste
electrical and electronic equipment should be disposed of in accordance with
specific rules with the implication of both suppliers and users. For this
reason your appliance should not be disposed of as unsorted municipal waste.
The user has the right to bring it to a municipal collection point performing
waste recovery by means of reuse, recycling or use for other applications in
accordance with the directions.
The warranty for your product is valid for two years from the date of
purchase. Activate Windows Go to Settings to activat
A Vreekesweid 30
1721 PR Broek op Langedijk
The Netherlands
T +31(0)226 33 14 20
Einfo@xaralyn.com
Wwww.xaralyn.com