SOLTER MI03217 Hellmet R-05 Instruction Manual

Hellmet R-05 INSTRUCTION MANUAL
INSTRUCTIONS FOR USE AND MAINTENANCE, READ THIS
MANUAL CAREFULLY BEFORE USING THE PROTECTIVE
SCREEN.
MI03217-01
07/2022

INTRODUCTION

 We appreciate your deference to our brand and we hope the welding screen you have just purchased will be of great use to you. This instruction manual contains the necessary warnings for correct use within the maximum safety conditions for the operator.  SOLTER welding filters must be used by expert personnel who know and understand the risks involved in using them. In case of misunderstanding or doubts about this manual, please contact us. Handling the weld filter carries a significant risk of injury.  Please refrain from doing any
manipulation on the filter or helmet. Only technically trained personnel can do it.
SOLTER Welding, SL declines all responsibility for negligent practices in use and / or handling. This manual should be attached and kept with the filter model purchased. These filters are designed and approved in  accordance with European Standard
EN  379.
It is the responsibility of the people who use and repair them that the product does not fail to meet the requirements of the aforementioned standards.

PRECAUTIONS

• Never place the helmet on a hot surface.
• Use only at temperature: -5°C to +55°C (23°F-131°F).
• Do not immerse the filter in water and protect it from contact with liquids and dirt.
• Material that may come into contact with the user’s skin may cause an allergic reaction.
• Any welding helmet worn over standard ophthalmic glasses can transmit impact, thus creating a hazard to wearers in some circumstances.
• This product cannot be used for overhead welding or cutting. If this product is used for overhead welding or cutting operations, the bead of molten metal can burn the helmet and injure the welder.
• The eye protector should only be used against high speed particles at room temperature.
• The automatic welding filter should always be used with a backup eyepiece.
• Unauthorized modifications and replacement parts will void the warranty and expose the operator to the risk of personal injury.
• Some auto-darkening welding helmets are not suitable for laser welding or welding processes that require shade 14 or higher.
• If the auto-darkening filter does not darken when the arc is struck, stop welding immediately and inspect the filter and its battery. Change if necessary.
• Do not use abrasive cleaning solvents or detergents on the filter screen or helmet components.
• We recommend a period of use of 4 years. The period depends on several factors, such as the way of use, cleaning, storage and maintenance. Frequent inspections and replacement in case of damage are recommended.
• Always wear safety glasses or goggles under the welding helmet and protective clothing to protect your skin from radiation, burns and spatter.
• Protectors that have been subject to impact should not be used, should be discarded and replaced.r.
• Protection marked in accordance with this standard is provided only when all lenses and retaining components are installed in accordance with the listing or other manufacturer’s instructions.
• This device does not protect against physical or chemical hazards.
• If the hull, filter or cover plate is damaged in any way, it must be replaced immediately.
• Replace device after mechanical impact.
• A visual inspection is necessary before each use.
• Not suitable for driving and road use.

BEFORE STARTING TO WELD

Before using any of the welding filters be sure to remove the corresponding protection films, keep the viewing area and the front part of the filter clean since there are the sensors that take care of the filter darkening.
Inspect all operating parts before using the display and check for signs of deterioration. Any damaged part must be replaced immediately before use. Check the operation of the filter before each use.
Also make sure that the attachment to the protection screen is correct to prevent it from detaching in the event of any impact, which could cause personal injury to the user.
In case the filter darkening DIN is adjustable, adjust correctly before any application. To find out the appropriate degree for all applications, consult the section FILTER CHOICE CHART ACCORDING TO APPLICATION of the protection screen manual.

TECHNICAL SPECIFICATIONS

All filters are marked as indicated by the CE certificate of each model. In this marking, the first number specifies the degree of DIN protection that the filter has when it is in the open state (clear), the next number indicates the DIN degree in the closed state  (dark) indicating the minimum and maximum degree. The symbol between the two numbers tells us if the DIN degree setting is manual or automatic. The next three numbers indicate the type of optics, the filter’s light dispersion and the uniformity of the  filter’s vision according to regulations.

The next three numbers indicate the European Regulation with which the filter complies.
PARTS OF THE FILTERS
WELDING / GRINDING selector :
Place the selector in the position of the process to be carried out.
Sensitivity :
Adjust it to a position that is not obscured by lighting in the work area.
Dimming selector :
Two level selection. 5-8 and 9-13
Darkening :
Fine adjustment between the selected limits.
Delay :
Set the time to go from dark to light mode.

TABLE FOR FILTERS ACCORDING TO APPLICATION

CORRIENTE EN AMPERIOS| CORTE DE
PLASMA| ELECTRO- DOS  RE- VESTIDOS| MIG METALES
PESADOS| MIG ALEACIONES LIGERAS| TIG| MAG| ARCO /
ARE| SOLDADURA
DE PLASMA
---|---|---|---|---|---|---|---|---
0,25| | | | | TONO 8| TONO 8| | TONO 2,5
0,5| | TONO 3
0,75| | TONO 4
1| | TONO 5
2,5| | TONO 6
5| | TONO 7
10| | TONO 8
15| | TONO 8| TONO 9| TONO 9
20| | TONO 10
30| | TONO 9| TONO 10
40| | TONO 11
60| | TONO 10| TONO 11| TONO 9
80| | TONO 12
100| TONO 11| TONO 11| TONO 10| TONO 12| TONO 10
125| | TONO11
150| | TONO11| TONO 13| TONO11| TONO 10| TONO 13
175|
200| TONO 12| TONO 12| TONO 12| TONO 12| TONO 12| TONO 11
225|
250| | TONO 13| TONO 14| TONO 13| TONO 12| TONO 14
275|
300| TONO 13| TONO 13
350| | TONO13| TONO13|  TONO 14
400| | TONO14| TONO14
450|
500| | TONO15| TONO15| TONO15
TONO 14| TONO 14| TONO 15

CHOOSING HARNESS
Harness height (Position W)
Adjust the harness to the appropriate depth on the head to ensure correct and stable balance.
Tighten the harness (Position Y)
Press the adjustment button on the back of the harness and turn it to the right or left to the appropriate position.
Adjust Distance (Z Position)
Adjust the distance between the face and the lens by loosening the two outer nuts equally and press inward to release it from the adjustment slots.
Angle Adjustment (X Position)
Four bolts on the upper right side of the harness provide an adjustment for future helmet lean. To adjust, loosen the adjustment knob on the right side, then lift the tab on the control arm and move it to the desired position and finally retighten the adjustment  knob. POSSIBLE FAULTS

positioned or the angle of the helmet with respect to our vision area is not adequate.
The filter does not darken or flickers (automatic filters)| The front protective filter is damaged or in poor condition.
The sensors are dirty.
The welding current is too low.
Slow filter response (automatic filters)| The working ambient temperature is too low.
Insufficient vision| The front or rear protective filters are dirty.
Wrong protection index.
Insufficient light in the work environment.

EXPLODED

Email: solter@solter.com

2006/95/CE (LVD, EMC), 2002/95/EC (ROHS), 2002/96/EC (WEE), 89/686/CEE

WARRANTY INFORMATION.

We offer a limited warranty for this product against any defects in material and workmanship for a period of 12 months from the date of purchase by the end user / consumer.
The warranty conditions are as follows:
The guarantee will only be valid with the presentation of the purchase invoice linked to the serial number of the equipment. The date of purchase must also appear.
The warranty does not cover defects due to misuse, incorrect installation, modification or manipulation of the product.
We are not responsible for damage caused by misuse or incorrect use of the equipment.
The warranty is limited to the repair of defective components.
In the event that the product is repaired or replaced, the warranty period will remain valid for the remaining period

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>