Ergosolid F160 LCD LED Monitors Instruction Manual

Ergosolid F160 LCD LED Monitors

Product Information

The F160 is a desk mount with a gas spring designed for displays with sizes ranging from 17 to 27 inches. It has a maximum load capacity of 2 to 9 kg (x2) and is compatible with VESA mounting patterns of 75×75 mm and 100×100 mm. The product also includes a high-pressure gas spring, which should not be dismantled without professional assistance. Please refer to the user manual for further instructions and safety precautions.

Product Usage Instructions

1. If the display can be hovered at any height after installation, no adjustment is needed.

2. If the display lifts up automatically after installation,
   follow these steps:

3. One person should press down on the screen while the other person turns the set screw at the bottom of the upper arm in the ‘-‘ direction to reduce torque. Use a 5mm Allen key (G) as shown in Fig-1 and Fig-2 until the display can be hovered at any desired position.

4. If the display sits at the lowest position after installation, repeat step 2 but turn the set screws in the ‘+’ direction to increase torque. Adjust as necessary until the display can be hovered at any desired position.

Please note that the product arm can be fully adjusted in multiple directions to ensure the performance of the gas spring. It is recommended to perform these adjustments several times per month.

Important Safety Information

• This product contains a high-pressure gas spring. Fire and percussion are strictly prohibited.
• Do not dismantle the product without professional assistance.
• If the product is abandoned, please return it to the manufacturer or hand it over to professional agencies.
• All images are for reference only. Actual product may vary.
• The manufacturer reserves the right to modify or alter instructions without formal notice. Do not make any modifications or alterations without proper notification.

Installation guide

Optional

Table edge installation
Warning
Ensure screws are secured firmly

Grommet Installation

Warning
Attention
Ensure screws are secured firmly

Directional Usage Guide

• For table edge
• For grommet

Working load

Cable routing

Display installation

VESA:75x75mm, 100x100mm

Warning
Attention
Ensure screws are secured firmly

Torque adjustment

1. If display can be hovered at any height after display installed. No adjustment needed.
2. If display lift up automatically after display installed, adjust the following: One man hand press down the screen, the other wind set screw at the bottom of upper arm at joint to ‘ – ‘ direction to reduce torque by using G, 5mm Allen key as shown in Fig-1 and 2 until display can be hovered at any point of positions.
3. If display sit at the lowest position after installation, repeat #2 procedures but winding set screws to ‘ + ‘ direction to increase torque as Fig-1 and 2 until display can be hovered at any point of positions.

Setting tilt angles

Display rotation

Only display comes with central gravity will has the best performance

Warning
Attention

1. Do not adjust tension without putting on display
2. Ensure display has been put onto mount
3. Working load

F160
Desk mount with gas spring
Display size: 17” ~ 27”
Max load : 2 ~ 9 kg (x2)
VESA: 75×75, 100×100 mm
Severe personal injury and property damage can result from improper installation or assembly

• If you do not understand the instructions or have any concerns or questions, please contact a qualified local installer.
• Do not install or assemble if the product or hardware is damaged or missing, if you require replacement parts, please contact you local distributor for assistance.
• This product fits most 17″-27″ LCD / monitor; maximum weight of LCD / monitor: 9 kg. Installer-friendly and straight forward.
• For safe installation, the desk you are mounting to must support minimum 3 times the weight of the total load (the mount, the monitor and all accessories weight).
• Do not use this product for other than the original designed.
• This product contain moving parts, please use with caution.
• When installing monitor, please do not damage electrical wiring or power source. Installation and routing of monitor cables on the monitor bracket must comply with electro-technical regulations.
• Importantly, mains- and data-cables must be secured against twisting and squeezing or shearing.
• The manufacturer will bear no responsibility to the desk of mounting, or incidental or consequential damages arising thereof.
• The manufacturer disclaims any liability for the modifications, improper installation, or installation over the specified weight range. The manufacturer will not be liable for any damages arising out of the use of , or inability to use, the product.
• This product is designed for indoor used only, use of this product outdoor could lead to product frailer and severe personal injury.
• This product contains a high pressure gas spring, fire and percussion prohibited. Also it is strictly prohibited to dismantle without professionals. Please return to the manufacturer or hand over to professional agencies if the product is abandoned. In order to ensure the performance of gas spring, full direction adjustment of the product arm is recommended several times per month.
• All images are for reference only. As product in kind prevail.

We reserve the right to modify or alter instructions. No modification or alteration without formal notice.

Kunshan Hongjie Electronics Co., Ltd 1050, Fu chun Jiang Road, Economic Development Zone, Kunshan City, Jiangsu Province, China 215333
Mail: info@nbavmount.com
www.nbavmount.com

ERGOSOLID SARL
36 rue du Louvre 75001 Paris, France
Tel. (+33)7 72 15 51 60
www.ergosolid.fr

References

• Bienvenue dans notre boutique en ligne Ergosolid.
• Supporti per TV, Monitor e Proiettori
• Fiber Novelty - Uchwyty do Telewizorów i Mobilne Stojaki TV - Sklep
• NB

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>