SENIGNOL END001 Electric Cordless Nail Drill Instruction Manual

SENIGNOL END001 Electric Cordless Nail Drill

Safety Instructions

In order to ensure the normal operation of the equipment, please read this manual carefully before use and keep it for future reference.

Warning

• This device should not be used on children, people with allergies, or people with skin inflammation of the fingers or toes. It should also not be used on people with physical, sensory or intellectual disabilities.
• If you feel uncomfortable when using this device, please stop using it and consult a doctor.
• Do not use this device for any purpose other than nail care.
• Do not modify, disassemble or repair the equipment by yourself.

Caution
The device built in a lithium battery. Do not place or store the equipment in a hot and humid environment for a long time. If the equipment is not used for a long time, please fully charge the product.

Product Specifications

• Name: portable nail drill
• Input: 5V= = 2A
• Battery type: 3.7V lithium battery 800mAh
• Charging time: about 40 minutes
• Working time: 2-4h
• Charging port: Type-C
• Weight: 134g
• Size: 170 * 23mm

Product Description

1. Power button/pause button/”F” or”R” button
2. Forward rotation and steering display
3. Battery display lamp
4. Speed up and Speed down
5. Bit lock system
6. Grinding head
7. Five speed display

Grinding Heads

Preparation Instructions

• Charging: Connect Type-C charging cable to the equipment charging port and interface adapter (not included) . When the device is charged, the indicator light will be red. When the battery power reaches 99%, the indicator light will be green.
• When the battery is low, the battery indicator will flash red. After the red charging indicator flashes for 3 minutes, the battery runs out of power and the product automatically shuts down.
• Charging takes about 40 minutes. The fully charged battery of the device can last for 2-4 hours.

Installation of grinding head:

• Step 1: Rotate the grindinghed locking system clockwise to unlocking mark(&), to unlock.
• Step 2: Remove the grinding head from the equipment.
• Step 3: Insert the grinding head you want to use.
• Step 4: Rotate the grinding head locking system counterclockwise to locking mark (8) to lock grinding head in place.

Usage

To ensure the correct operation of this product, please read the instructions carefully before use.

• Select and install accessories according to your needs. When installing the grinding head, firmly insert it into the bottom of the product and fix it.
• Turn on: press and hold power button for 2 seconds to turn on the device, the grinding head starts to rotate, and the “F’/”‘R” indicator lights up.
• Rotation direction switching: when the product is in working state, double click the power button quickly, and the grinding head can rotate alternately in the positive and negative directions. “F” indicator is on when forward rotation is selected and “R” indicator is on when reverse rotation is selected.
• Increase the rotation speed: press the “+” button briefly to increase the rotation speed by one level. The speed can be adjusted for 5 times at most.
• Decrease the rotation speed: press the “-” button briefly to decrease the rotation speed by one level.
• The speed can be adjusted for 5 times at most.
• Pause the device: When you need to stop using the device, briefly press the power button. The grinding head stops rotating, and the equipment enters standby mode. The standby time is 120 seconds. If there is no operation during this period, the device will automatically shut down.
• Turn off: After the equipment is used, long press the power button to turn off the equipment. You can also press the power button to pause the device, and it will automatically turn off after 120 seconds.
• Use while charging: You can use it while the device is charging. You can also wait until the product is fully charged before using it.
• Motor locking protection system: If the grinding head touches a hard surface, press with force, and all indicator lights flash continuously for 6 seconds to remind you to lift the grinding head. If you do not lift the grinding head from the surface, the device will automatically turn off after 6 seconds.

Cleaning and Maintenance

• Before starting cleaning, make sure that the device is turned off.
• Do not immerse the equipment in water. Accessories can be cleaned separately.
• Use a clean, slightly damp cloth to clean the equipment surface.
• Do not use lubricants, cleaners, polishes or air fresheners on this equipment.
• Replace the spindle: This product can replace the spindle. When you use the equipment improperly and the product is noisy and does not rotate smoothly, you may need to replace the spindle. The steps and illustrations are as follows:

Replace and install the bearing:

• Step 1: Rotate the pen head counterclockwise, unscrew and take it out.
• Step 2: Remove the damaged spindle from the equipment.
• Step 3: Install the good spindle.
• Step 4: Rotate the pen head clockwise and install it into the device, and tighten it firmly.

Recycling

The built-in battery of the device may contain substances that pollute the environment. Remove the battery when handling this device. Do not enter fire or household waste through equipment and batteries. Please comply with local government regulations and properly handle the battery to help protect the environment.

After Sales Service

Troubleshooting
If you encounter any of the following problems, review this troubleshooting section. If you cannot find a solution and the problem still exists, please contact our Amazon customer service.

• Q: The equipment does not work.
  A: Check whether the equipment is low in electricity and confirm whether it needs electricity generation; Please check whether the bit lock system forgot to lock; If you have other questions, please contact us via Message in time, and we will provide help within 24 hours

• Q: The drill bit cannot cooperate with the equipment or falls out.
  A: Please check whether the drill bit is correctly inserted and locked. You can also verify that the diameter of the bit is too large for the equipment bit inlet.

• Q: All device LEDs are flashing.
  A: The surface is too hard. You can increase the speed or grind from the surface.

Important Safety Matters

Warning – Basic precautions should always be followed when using this product.

It includes the following:
Please read all instructions before use.

• Do not drop, knock or disassemble the machine.
• Do not operate in wet or humid conditions.
• Do not damage or modify the equipment in any way.
• Do not expose to fire or extreme temperatures.
• Keep away from high temperature, flammable, toxic and corrosive substances.
• Do not attempt to repair the equipment. If the equipment is damaged, it should be repaired or replaced by an authorized professional.
• Dispose according to local laws and regulations.

FCC Specification

This device complies with Part 15 of the FCC Rules. The operation shall meet the following two conditions:

1. This equipment shall not cause harmful interference.
2. This equipment can accept any interference, including interference that may cause abnormal operation.

Recycling instruction for scrapped electronic and electrical equipment
Properly dispose of this product (waste electrical and electronic equipment) (applicable to countries with separate collection systems) This mark on the product, accessories or literature indicates that this product and its electronic accessories should not be disposed of together with other domestic wastes at the end of their service life. To prevent uncontrolled waste disposal from causing damage to the environment or human health, please separate these projects from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Home users should contact the retailer or local government office that purchased the product to find out where and how to recycle these products, so as to achieve environmentally safe recycling.

MADE IN CHINA
Please read the instructions carefully before using this product

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>